TopflyTech SolarGuardX 100 GPS E-Lock User manual

TOPFLYtech SolarGuardX 100 GPS E-Lock
User Manual
20220329

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 2
Thanks for your purchasing of the high-quality GPS tracker from TOPFLYtech. Please read this user
manual carefully before installation and operation. Information in this manual is the property of
TOPFLYtech. Changes to the specifications and features in this manual may be made by
TOPFLYtech without prior notice. No part of this manual could be reproduced, copied, translated,
transmitted, or published in any form or by any means without TOPFLYtech's prior written
permission.
SolarGuardX 100
The GPS E-Lock is using GNSS & LTE technologies and could collect device coordinates then
transfer them via LTE network to the server. It provides customer with cost-effective, efficient and
safety management. It has been widely used in commercial transportation, company vehicle fleet
management, intelligent transportation, logistics, car rental, engineering machinery, marine
transportation, animal/pet tracking and other segments.

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 3
Contents
1. QUICK REFERENCE .............................................................................................................................. 4
2. PRODUCT SPECIFICATIONS .............................................................................................................. 5
3. STANDARD ACCESSORIES INTRODUCTION ................................................................................ 7
4. LED INDICATOR ................................................................................................................................... 7
5. INSTALLATION GUIDE ....................................................................................................................... 8
5.1 SIM CARD PRE-INSTALLATION NOTE ............................................................................................................ 8
5.2 SIM CARD INSTALLATION AND TRACKER POWER SWITCH ........................................................................... 8
5.3 FIX SCREWS ..................................................................................................................................................... 8
5.4 INSTALLATION ................................................................................................................................................. 9
6. TRACKER OPERATION ........................................................................................................................ 9
6.1 PHYSICAL POWER ON OR OFF ........................................................................................................................ 9
6.2 THE BATTERY ................................................................................................................................................... 9
6.3 GET CURRENT POSITION ................................................................................................................................ 9
7. ALARM CONFIGURATION .............................................................................................................. 10
ALARM CONFIGURATION PLEASE VIA THE TOPFLYTECH CONFIGURATION TOOL. ............................................... 10
8. QUICK TROUBLE SHOOTING ......................................................................................................... 10
8.1 UNABLE TO CONNECT TO THE TRACKING PLATFORM .............................................................................. 10
8.2 TRACKER SHOWS OFFLINE .......................................................................................................................... 10
8.3 UNABLE TO LOCATE .................................................................................................................................... 10
8.4 POSITION DRIFT ........................................................................................................................................... 10
8.5 NO COMMAND REPLY ................................................................................................................................ 10
9. WARRANTY AND STOCK ............................................................................................................... 10
10. FREQUENTLY USED COMMANDS............................................................................................ 10
10.1 UNLOCK SETTING......................................................................................................................................... 11
10.2 APN SETTING .............................................................................................................................................. 11
10.3 SERVER SETTING ........................................................................................................................................... 12
10.4 UPLOAD INTERVAL SETTING........................................................................................................................ 12
10.5 HEARTBEAT SETTING.................................................................................................................................... 12
10.6 PIN SETTING ................................................................................................................................................ 13
10.7 GOOGLE MAP SEARCH................................................................................................................................ 13
10.8 FORGOT THE PIN ......................................................................................................................................... 13
11. OPTIONAL ACCESSORIES LIST ................................................................................................. 13
12. FCC WARNING.............................................................................................................................. 14
13. ISEDC WARNING .......................................................................................................................... 15

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 4
1. Quick Reference
Attention
i. SolarGuardX 100 obtains power through sunlight to extend the battery life.
ii. Please make sure that the device is exposed to direct sunlight every day. This will be
very useful to extend the battery life. If the device is not charged for more than three
months, it may cause permanent damage to the internal battery.
iii. Please give the device a fully charging before installation.
iv. Only when the solar panel output voltage value is 0.3V higher than device battery
voltage value, the solar panel will start to charge the battery. Otherwise, the solar
charging will stop.
v. To ensure the battery life for longer period, please be careful to set the reporting
intervals. Lower reporting rates will maintain the balance between the power
consumption and gaining (from solar panel). We usually recommend set the tracker
reporting ≥every 5 mins when moving, and ≥every 1 hour when standstill. Customer
may also contact with TOPFLYtech for further advice.
Equipment power consumption and solar panel charging current
i. The normal device power consumption is around 40mAh when the device is in working
mode without sleep.
SolarGuardX 100

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 5
ii. The typical charging rate of the solar panel under direct sunlight at noon (in summer) is
about 330mAh (different sunlight illumination, different charging current).
Disclaimer: Before using this device, customers should fully understand their usage scenarios
and installation environment. TOPFLYtech will not be responsible for any lost caused by using
the device in a wrong scenario or reporting rate. It is highly recommended that customers
should contact TOPFLYtech before deployment. We are glad to give suggestions.
Intelligent Power Management
To extend the battery life, we designed an intelligent power management algorithm. This
algorithm allows the tracker working under a lower reporting rate when battery is low. Once
the battery is charged back, the tracker will report as normal. This function is enabled in
default. Customer can disable it by command. The detail working logic is:
 When the battery voltage value is down to 3.4V, then the tracker will report at every 24
hours no matter moving or standstill.
 When the battery is charged back to 3.5V, the device will report as what are set by
customer.
FOTA (firmware over the air) Notification
TOPFLYtech is committed to providing clients with the best user experience. We are offering
automatic firmware update feature for every device. This feature allows devices always having the
latest version firmware. It can save clients the time and effort of updating firmware manually.
Please note that this feature is enabled in default. If you want to turn it off, please contact with
TOPFLYtech. If this feature is disabled, the FW update only can be done by sending upgrade
command manually.
2. Product Specifications
Network Specifications
Operating Band LTE FDD Cat M1:
B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/
B20/B25/B26/B28/B66/B85
LTE FDD Cat NB2:
B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/
B25/B28/B66/B71/B85
GSM/EDGE: 850/900/1800/1900MHz
Data Transmission eMTC: Max. 588 (DL), Max. 1119 (UL)
NB1: Max. 32Kbps (DL), Max. 70Kbps (UL)
NB2: Max. 127 (DL), Max. 158.5 (UL)
EDGE: Max. 296Kbps (DL), Max. 236.8Kbps (UL)
GPRS: Max. 107Kbps (DL), Max. 85.6Kbps (UL)
GNSS Specifications

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 6
GNSS Chipset MediaTek High Gain GNSS receiver
GNSS System GPS+Glonass or GPS+Beidou
Receiver type: 33 tracking / 99 acquisitions- channel GNSS
receiver
Sensitivity Cold start: -149 dBm
Tracking: -167 dBm
Horizontal Position Accuracy < 2.5m CEP
TTFF @ -130 dBm with (without) EASY™ Cold Start: < 15s (32s)
Warm Start: < 8s (28s)
Hot Start: < 1s (1s)
Interfaces
Charging Port 2 Pin 5V/DC
E-Lock Configuring Port Type-C connector
Network, GNSS Antenna Internal only
Indicator LED Battery, Network, GNSS, RFID
FOTA Yes
Physical Power Switch 1
Temperature Sensor 1 temperature sensor
BLE 5.1 Yes
General Specifications
Waterproof IP67
Dimensions 207.5mm*110.2mm*48.1mm(8.17”*4.39”*1.9”)
Weight 1050g (37oz)
Battery Rechargeable Li-Polymer 14400 mAh/ 3.6V
Standby Time
(Without solar charging, 2 hours active
tracking per day)
10 minutes reporting: 402 Days
5 minutes reporting: 315 Days
1 minute reporting: 144 Days
Charging 2 PIN
(Recommend using 5V 1A adaptor, 30 hours
charging)
Operating Temperature -25℃ ~ +70℃ (-13°F ~ 158°F)
Mounting Built-in Magnet
Air Interface Protocol
Transmit Protocol TCP, UDP, MQTT, SMS
Data Security & Encryption Option MD5/ AES256
BLE Accessory Support Yes
Scheduled Timing/angle/distance Report Report position and status at preset intervals
Geo-fence Support up to 64 internal geo-fence regions
Alarms Rope cut, Moving, Stop, Lock, Unlock
Industry Certifications (Planning)
CE, RCM, IC, FCC, PTCRB, AT&T, US Cellular, T-Mobile, Verizon

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 7
3. Standard Accessories Introduction
4. LED indicator
Note: Indicator lights will go out automatically after the tracker turns on for 70 seconds without
connecting to the external power via USB cable.
LED indicator working status:
Solid on: LED indicator on and no flashing
Fast flashing: 0.25 second on and 0.25 second off
Slow flashing: 1 second on and 1 second off
Unlock: Unlock successfully, RFID LED indicator will show solid on until plug out the lock rope. If

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 8
the rope isn’t taken out in 60 seconds, device will lock again, and LED indicator goes off.
Lock: After lock successfully, RFID LED indicator will be fast flashing for 2 seconds then off.
Wake up the device: Device gets the wake up info, RFID LED indicator will show slow flashing
300 seconds or get the unlock command from server side then switch to unlock process.
Incorrect RFID Card or Correct RFID Communication Error: Network & GNSS & RFID LED Fast
flashing 5 seconds.
Lock Error: Network & GNSS & RFID LED on (The maximum duration of continuous light is 300
seconds then off or the error disappear) – This is mechanical failure.
Unlock Error: GNSS & RFID LED on (The maximum duration of continuous light is 300 seconds
then off or the error disappear) – This is mechanical failure.
5. Installation Guide
5.1 SIM card pre-installation note
5.1.1 SIM card data service should be enabled.
5.1.2 If SIM card is locked via PIN, please unlock it first.
5.1.3 Ensure there is sufficient balance in the SIM card.
5.2 SIM card installation and tracker power switch
5.2.1 Open the tracker SIM card cover with the screwdriver.
5.2.2 Unlock SIM cover and insert sim card then lock. Turn the power switch from off
to on.
5.2.3 Put the cover back and use screwdriver to fix the cover tightly.
5.3 Fix Screws

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 9
5.3.1 It is VERY IMPORTANT to fix the 4 SIM card cover screws to prevent water from
leaking inside and cause damage to device.
5.3.2 TOPFLYtech offers the electric screwdriver (TA38) as an optional accessory to help
customer standardize the screw fixing strength.
5.3.3 Please use strength level 8 if using TOPFLYtech electric screwdriver (TA38)
5.3.4 For third party electric screwdriver, please use torque 3.5kgf.cm.
5.4 Installation
5.4.1 Away from emission source such as all kinds of sensors, burglar alarm and other
communication devices.
6. Tracker Operation
6.1 Physical power on or off
6.1.1 Turn the power switch to on or off position.
6.1.2 Physical power off is recommended when the tracker is stored in the warehouse.
6.2 The battery
6.2.1 Place the tracker solar panel side on the desk
6.2.2 Recommend connecting the device to a 5V 1A (cellphone) adaptor through
magnet USB cable for 30 hours charging to make sure the battery is fully charged.
6.2.3 Customer also can connect the tracker to other USB connectors. But lower current
output will cause longer charging time.
6.2.4 When the battery voltage value drops to 3.3V, usually a battery charging is
needed to avoid unexpected shutdown due to low power. If the battery runs out
completely, please keep the tracker charging for 24 hours first. Only when the
battery is charged to 3.5V, the device will power on again.
6.3 Get Current Position
6.3.1 SMS Query (only when the device in working mode and registered on the network)
Device default PIN is 0000. Send a location inquiry SMS command (google,0000#)
to the tracker. The location information will be sent back through SMS (the tracker
SIM card must support receiving and sending SMS first).

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 10
6.3.2 Platform Query
Connect your tracker to the tracking platform then check the real-time position
online. (Additional tracking service charge may happen. Contact with your service
provider to get more details)
7. Alarm Configuration
Alarm configuration please via the TOPFLYtech configuration tool.
8. Quick Trouble Shooting
8.1 Unable to Connect to the Tracking Platform
8.1.1 Check the APN and IP settings.
8.1.2 Check the SIM card data service whether enabled.
8.1.3 Make sure there is no limitation or already added server IP to the SIM card IP
whitelist when using a M2M SIM card.
8.1.4 Check the balance/data of the SIM card.
8.2 Tracker Shows Offline
8.2.1 Check the battery remaining power
8.2.2 Check if the device entered into network blind area.
8.2.3 Check the SIM card balance.
8.2.4 If the connection lost happens on the last several days of the month, check
whether the network service is terminated by carrier because of exceeding the
max data usage volume.
8.3 Unable to Locate
8.3.1 The device may shield by metallic things.
8.3.2 The device may enter into an area with no satellite signal coverage.
(Underground, building, etc)
8.4 Position Drift
In an area with poor GNSS signal (like the areas with lots of high buildings), position drift
may happen. When the device moves to open area, the drift will no longer exist.
8.5 No Command Reply
8.5.1 Check the command format. Make sure it’s correct.
8.5.2 The device may be in network blind area.
8.5.3 Ensure the SIM card is properly inserted.
9. Warranty and Stock
The device standard warranty period is 12 months starting from the date of purchasing. If the
device will be stored for a long time, please connect it to the external power and recharge the
internal battery (20 hours) every 3 months. It will be helpful to extend the internal battery life.
10. Frequently Used Commands
Commands are not case-sensitive and can be sent via mobile phone. The content is separated

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 11
by comma and ends with #. When set successfully, the tracker will return OK and execute it.
Otherwise, there will be no message returned.
Function Command Format
Unlock Unlock ,Unlock PIN #
APN Setting APN ,Current PIN , APN Name , Username , Password #
Server Setting IP ,Current PIN , Server Domain Name or IP , Port Number #
Upload Interval Setting TIMER,
Current PIN , Upload Time(ACC on) : Upload Time(ACC
off) : Angle Compensation : Distance Compensation #
Heartbeat Setting HBT, Current PIN , Heartbeat Interval #
PIN Setting PASSWORD, Current PIN , New PIN #
Google Map Search GOOGLE, Current PIN #
Forgot the PIN MYSELF#
10.1 Unlock Setting
Unlock ,Unlock PIN #
Unlock PIN:
Range: 6 numbers
Length Limit: 6
Note: The unlock PIN is different from device PIN
10.2 APN Setting
APN, Current PIN,APN Name,Username,Password#
APN Name:
Range: APN of service provider
Length Limit: 1~32
Username:
Range: Letters and Numerals
Length Limit: 0~32
Password:
Range: Letters and Numerals
Length Limit: 0~32

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 12
Note:
1) Tracker will return “SET APN OK” when received this command.
2) If there is no Username and Password, the SMS setting is:
APN,Current PIN,APN Name,,#
3) If there is no APN PIN, the SMS setting is:
APN,Current PIN,APN Name,Username,#
10.3 Server Setting
IP, Current PIN,Server Domain Name or IP,Port Number#
Server Domain Name or IP:
Range: Letters, Numerals and Symbols
Length Limit: 1~128
Port Number:
Range: Positive Integer
Length Limit: 0~65535
Note: Tracker will return “SET IP OK” when received this command.
10.4 Upload Interval Setting
TIMER, Current PIN,Upload Time(ACC on):Upload Time(ACC off):Angle Compensation:
Distance Compensation#
Upload Time (ACC on):
Range: Positive Integer
Range Limit: 0, 3~65535 second
Upload Time (ACC off):
Range: Positive Integer
Range Limit: 0, 1200~ 4294967295 second
Angle Compensation:
Range: Positive Integer
Range Limit: 0~90 degrees
Distance Compensation:
Range: Positive Integer
Range Limit: 0 ~ 65535 meters
Note: Tracker will return “SET TIMER OK” when received this command.
10.5 Heartbeat Setting
HBT, Current PIN,Heartbeat Interval#

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 13
Heartbeat Interval:
Range: Positive Integer
Range Limit: 1 ~ 255 minutes
Default: 30 minutes
Note: Tracker will return “SET HBT OK” when received this command.
10.6 PIN Setting
PASSWORD, Current PIN,New PIN#
PIN:
Range: Letters and Numerals
Length Limit: 1 ~ 10
Default: 0000
Note: Tracker will return “SET PASSWORD OK” when received this command.
10.7 Google Map Search
GOOGLE, Current PIN#
Note: Tracker will return below message when received this command.
http://maps.google.com/maps?q=<Latitude>, <Longitude>
10.8 Forgot the PIN
MYSELF#
Note:
1) If the manager phone number has been set, only the manager can use “MYSELF#”.
If no manager setting, the tracker will return the IMEI and current PIN when it
received “MYSELF#” from any mobile phone.
2) This command can be used to retrieve password.
11. Optional Accessories List
Product Sku Description Photo for Reference
TSTH1-B BLE 5.0 Wireless Temperature
and Humidity Sensor

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 14
TSDT1-B BLE 5.0 Wireless Door and
Temperature Sensor
TSR1-B BLE 5.0 Wireless Relay
TR021 Lock Rope (400mm)
12. FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 15
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
13. ISEDC Warning
This device complies with Innovation, Science, and Economic Development Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
The device is compliance with RF exposure guidelines, users can obtain Canadian information
on RF exposure and compliance.The minimum distance from body to use the device is 20cm.
Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites
d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux radiofréquences et la
conformité and compliance d’acquérir les informations correspondantes. La distance minimale
du corps à utiliser le dispositif est de 20cm.