TopflyTech TLP1-LF User manual

TOPFLYtech TLP1-LF Asset GPS Tracker
User Manual
20201014

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 2
Thanks for your purchasing of the high-quality GPS tracker from TOPFLYtech. Please read this user
manual carefully before installation and operation. Information in this manual is the property of
TOPFLYtech. Changes to the specifications and features in this manual may be made by
TOPFLYtech without prior notice. No part of this manual could be reproduced, copied, translated,
transmitted, or published in any form or by any means without TOPFLYtech's prior written
permission.
The tracker is using GNSS & LTE technologies and could collect device coordinates then transfer
them via LTE network to the server. It provides customer with cost-effective, efficient and safety
management. It has been widely used in commercial transportation, company vehicle fleet
management, intelligent transportation, logistics, car rental, engineering machinery, marine
transportation and other segments.
TLP1-LF

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 3
Contents
1. QUICK REFERENCE ..............................................................................................................................5
2. PRODUCT SPECIFICATIONS..............................................................................................................5
3. STANDARD ACCESSORIES INTRODUCTION ................................................................................6
4. LED INDICATOR ...................................................................................................................................6
5. INSTALLATION GUIDE .......................................................................................................................7
5.1 SIM CARD PRE-INSTALLATION NOTE............................................................................................................7
5.2 SIM CARD INSTALLATION AND TRACKER POWER SWITCH ...........................................................................7
5.3 INSTALLATION .................................................................................................................................................7
6. TRACKER OPERATION........................................................................................................................7
6.1 PHYSICAL POWER ON OR OFF ........................................................................................................................7
6.2 MOTION OPERATIONS....................................................................................................................................7
6.2.1 Check the battery status.....................................................................................................................7
6.2.2 Check the GNSS and network status .............................................................................................8
6.2.3 Send SOS alarm.....................................................................................................................................8
6.2.4 Quick set/cancel the geofence.........................................................................................................8
6.2.5 Motion controlled power on or off ................................................................................................8
6.3 THE BATTERY ...................................................................................................................................................8
6.4 GET CURRENT POSITION................................................................................................................................8
7. ALARM CONFIGURATION.................................................................................................................9
7.1 ALARM SENT THROUGH NETWORK................................................................................................................9
7.2 ALARM SENT THROUGH SMS........................................................................................................................9
8. QUICK TROUBLE SHOOTING............................................................................................................9
8.1 UNABLE TO CONNECT TO THE TRACKING PLATFORM.................................................................................9
8.2 TRACKER SHOWS OFFLINE.............................................................................................................................9
8.3 UNABLE TO LOCATE .................................................................................................................................... 10
8.4 POSITION DRIFT........................................................................................................................................... 10
8.5 NO COMMAND REPLY ................................................................................................................................ 10
9. WARRANTY AND STOCK ............................................................................................................... 10
10. FREQUENTLY USED COMMANDS............................................................................................ 10
10.1 APN SETTING .............................................................................................................................................. 11
10.2 SERVER SETTING........................................................................................................................................... 11
10.3 UPLOAD INTERVAL SETTING........................................................................................................................ 11
10.4 PIN SETTING ................................................................................................................................................ 12
10.5 ADD MANAGER PHONE NUMBER.............................................................................................................. 12
10.6 DELETE MANAGER PHONE NUMBER ......................................................................................................... 13
10.7 LIST MANAGER PHONE NUMBER............................................................................................................... 13

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 4
10.8 GOOGLE MAP SEARCH................................................................................................................................ 13
10.9 FORGOT THE PIN......................................................................................................................................... 13
11. OPTIONAL ACCESSORIES LIST ................................................................................................. 13
12. FOTA NOTIFICATION .................................................................................................................. 13
13. FCC WARNING.............................................................................................................................. 14

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 5
1. Quick Reference
2. Product Specifications
Network Specifications
Operating Band
FDD: B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/
B20/B25/B28
TDD: B39 (Cat M1 only)
EGPRS 850/900/1800/1900MHz
Certification
FCC: B2/B4/B5/B12/B13/B25
(Cat M1 and NB-IoT)
Data Transmission
eMTC: Max. 300Kbps (DL), Max. 375Kbps (UL)
NB1: Max. 32Kbps (DL), Max. 70Kbps (UL)
EDGE: Max. 296Kbps (DL), Max. 236.8Kbps (UL)
GPRS: Max. 107Kbps (DL), Max. 85.6Kbps (UL)
GNSS Specifications
GNSS Chipset
Qualcomm Gen 8C GNSS receiver
GNSS System
GPS+Glonass+Galileo+Beidou
Receiver type:
33 tracking / 99 acquisitions- channel GNSS
receiver
Sensitivity
Cold start: -149 dBm
Tracking: -163 dBm
Position Accuracy in open sky (CEP-50)
< 2m
Standalone TTFF
Cold start: < 29s
Warm start: < 27s
Hot start: < 1s
Interfaces
Data Transmission
4 Pin port with magnet
Network, GNSS Antenna
Internal only

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 6
Indicator LED
Network, GNSS and Battery
FOTA
Yes
Physical Power Switch
1
Light Sensor
1 back light sensor
Temperature Sensor
1 temperature sensor
General Specifications
Waterproof
IP67
Dimensions
69.3mm*143mm*24.8mm (2.72” *5.63” *0.98”)
Weight
210g (7.4oz)
Battery
Non-rechargeable 8100 mAh/3.6V Li battery
Standby Time
1 Year @ every 2 hrs reporing
3 Years @ every 12 hrs reporing
5 Years @ every 24 hrs reporing
Max every 5 mins reporting in recovery mode
Data Communication
Magnet USB cable
Operating Temperature
-20℃ ~ +60℃ (-4°F ~ 140°F)
Mounting
Magnet/Screw
Air Interface Protocol
Transmit Protocol
TCP, UDP, MQTT, SMS
Data Security & Encryption Option
MD5/ AES256
Scheduled Timing Report
Report position and status at preset intervals
Geo-fence
Support up to 64 internal geo-fence regions
Alarms
Support up to 29 types of alarm
(refer 7. Alarm Configuration)
3. Standard Accessories Introduction
4. LED indicator

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 7
Note: Indicator lights will go out automatically after the tracker turns on for 70 seconds without
connecting to the external power via USB cable.
5. Installation Guide
5.1 SIM card pre-installation note
5.1.1 SIM card data service should be enabled.
5.1.2 If SIM card is locked via PIN, please unlock it first.
5.1.3 Ensure there is sufficient balance in the SIM card.
5.2 SIM card installation and tracker power switch
5.2.1 Open the tracker with the screwdriver.
5.2.2 Open the SIM card slot
5.2.3 Insert and fix the SIM card.
5.2.4 Turn the power switch to on position before using.
5.3 Installation
5.3.1 Away from emission source such as all kinds of sensors, burglar alarm and other
communication devices.
6. Tracker Operation
6.1 Physical power on or off
6.1.1 Turn the power switch to on or off position.
6.1.2 Physical power off is recommended when the tracker is stored in the warehouse.
6.2 Motion operations
Device uses motion to detect different operations. Hold the tracker and keep the brand
label side towards the sky. Use normal speed to turn it over 180°(the brand label side
towards the ground) then recover. This is called one-time standard turning. By repeating
the standard turning different times, the tracker will execute different operations:
6.2.1 Check the battery status

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 8
(1) It only works when physical power switch at on position
(2) Repeat the standard turning 3 times
6.2.2 Check the GNSS and network status
(1) It only works when physical power switch at on position
(2) Repeat the standard turning 4 times
6.2.3 Send SOS alarm
(1) It only works when physical power switch at on position.
(2) Customer has to enable the alarm first (alarm_set,0000,3,1,0,0,#)
(3) Repeat the standard turning 5 times
(4) If customer wants to disable the alarm, command is (alarm_set,0000,3,0,0,0,#)
6.2.4 Quick set/cancel the geofence
(1) It only works when physical power switch at on position.
(2) Customer has to enable the function by command gfence_en first
(3) gfence_en,0000,a,b# (a=0, disable; a=1, enable; b=1~65535, unit is meter)
(4) Set geofence: repeat the standard turning for 6 times then the GNSS light
will slowly flash at the beginning. Once the geofence is set successfully, the
GNSS light will stay on without flashing then goes out shortly
(5) Cancel geofence: after the geofence is set, repeat the standard turning for 6
times. The tracker GNSS light will fast flash at the beginning. Once the
geofence is cancelled successfully, the GNSS light will stay on without flashing
then goes out shortly.
6.2.5 Motion controlled power on or off
(1) It only works when physical power switch at on position.
(2) Motion controlled power off: Repeat the standard turning 7 times. The
tracker will power off. Customer can repeat other motion operation to verify.
(3) Repeat the standard turning 5 times
(4) Motion controlled power on: after power off, repeat the standard turning 7
times, then all the LED will be flashing. The tracker will power on.
6.3 The battery
6.3.1 When the battery voltage value ≤3.4V, it stands for low battery. Customer has
to replace the battery with a new one to avoid unexpected shutdown.
6.4 Get Current Position
6.4.1 SMS Query (only when the device in working mode and registered on the network)
Device default PIN is 0000. Send a location inquiry SMS command (google,0000#)
to the tracker. The location information will be sent back through SMS (the tracker
SIM card must support receiving and sending SMS first).
6.4.2 Platform Query

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 9
Connect your tracker to the tracking platform then check the real-time position
online. (Additional tracking service charge may happen. Contact with your service
provider to get more details)
7. Alarm Configuration
7.1 Alarm sent through network
7.1.1 alarm_set,0000,a,b,0,0,#
7.1.2 0000 is device default PIN
7.1.3 a=alarm code, value from 1~3, 5~15, 18~22, and 24~31
Alarm Code
Description
Alarm Code
Description
1
Device removal (VS alarm 21)
18
Idle start (VS alarm 19)
2
Rear cover open (VS alarm 22)
19
Idle stop
3
SOS
20
Power on (via function button)
5
Start falling (VS alarm 24)
21
Device mounted
6
Low battery (Vs alarm 7)
22
Rear cover close
7
Battery recover
24
Stop falling
8
Device high temperature (VS alarm 25)
25
Device high temperature disappear
9
Vibration start (VS alarm 26)
26
Vibration stop
10
Collision (VS alarm 27)
27
Collision stop
11
Tilt start (VS alarm 28)
28
Tilt stop
12
USB cable connected (VS alarm 13)
29
Power off (via function button)
13
USB cable disconnected
30
Device low temperature (VS alarm 31)
14
Enter geofence (VS alarm 15)
31
Device low temperature disappear
15
Leave geofence
7.1.4 b=enable or disable, value is 0 (disable) or 1 (enable)
7.2 Alarm sent through SMS
Alarm also can be sent through SMS. But the tracker SIM card must support SMS function
first. Then it needs customer set manager cellphone number. Please refer the frequently
used commands part to get further information. Related commands: managera,
managerd, manager.
8. Quick Trouble Shooting
8.1 Unable to Connect to the Tracking Platform
8.1.1 Check the APN and IP settings.
8.1.2 Check the SIM card data service whether enabled.
8.1.3 Make sure there is no limitation or already added server IP to the SIM card IP
white list when using a M2M SIM card.
8.1.4 Check the balance/data of the SIM card.
8.2 Tracker Shows Offline
8.2.1 Check the battery remaining power
8.2.2 Check whether the device entered into network blind area.

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 10
8.2.3 Check the SIM card balance.
8.2.4 If the connection lost happens on the last several days of the month, check
whether the network service is terminated by carrier because of exceeding the
max data usage volume.
8.3 Unable to Locate
8.3.1 The device may shield by metallic things.
8.3.2 The device may enter into an area with no satellite signal coverage.
(underground, building, etc)
8.4 Position Drift
In an area with poor GNSS signal (like the areas with lots of high buildings), position drift
may happen. When the device moves to open area, the drift will no longer exist.
8.5 No Command Reply
8.5.1 Check the command format. Make sure it’s correct.
8.5.2 The device may be in network blind area.
8.5.3 Ensure the SIM card is properly inserted.
9. Warranty and Stock
The device standard warranty period is 12 months starting from the date of purchasing. If the
device will be stored for a long time, please turn the physical power switch to off position.
10. Frequently Used Commands
Commands are not case-sensitive and can be sent via mobile phone. The content is separated
by comma and ends with #. When set successfully, the tracker will return OK and execute it.
Otherwise there will be no message returned.
Function
Command Format
APN Setting
APN ,Current PIN , APN Name , Username , Password #
Server Setting
IP ,Current PIN , Server Domain Name or IP , Port Number #
Upload Interval Setting
TIMER, Current PIN , Upload Time(ACC on) : Upload Time(ACC
off) : Angle Compensation : Distance Compensation #
PIN Setting
PASSWORD, Current PIN , New PIN #
Add Manager Phone Number
MANAGERA, Current PIN , Manager Code : Manager Phone Number #
Delete Manager Phone Number
MANAGERD, Current PIN , Manager Code #
List Manager Phone Number
MANAGERL, Current PIN #
Google Map Search
GOOGLE, Current PIN #

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 11
Forgot the PIN
MYSELF#
10.1 APN Setting
APN, Current PIN,APN Name,Username,Password#
APN Name:
Range: APN of service provider
Length Limit: 1~32
Username:
Range: Letters and Numerals
Length Limit: 0~32
Password:
Range: Letters and Numerals
Length Limit: 0~32
Note:
1) Tracker will return “SET APN OK” when received this command.
2) If there is no Username and Password, the SMS setting is:
APN,Current PIN,APN Name,,#
3) If there is no APN PIN, the SMS setting is:
APN,Current PIN,APN Name,Username,#
10.2 Server Setting
IP, Current PIN,Server Domain Name or IP,Port Number#
Server Domain Name or IP:
Range: Letters, Numerals and Symbols
Length Limit: 1~128
Port Number:
Range: Positive Integer
Length Limit: 0~65535
Note: Tracker will return “SET IP OK” when received this command.
10.3 Upload Interval Setting
TIMER, Current PIN,Upload Time(ACC on):Upload Time(ACC off):Angle Compensation:
Distance Compensation#
Upload Time (ACC on):
Range: Positive Integer

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 12
Range Limit: 0, 3~65535 second
Default: 0
Upload Time (ACC off):
Range: Positive Integer
Range Limit: 0, 3~ 4294967295 second
Default: 86400
Angle Compensation:
Range: Positive Integer
Range Limit: 0~90 degrees
Default: 0 degrees
Distance Compensation:
Range: Positive Integer
Range Limit: 0 ~ 65535 meters
Default: 0 meters
Note: Tracker will return “SET TIMER OK” when received this command.
10.4 PIN Setting
PASSWORD, Current PIN,New PIN#
PIN:
Range: Letters and Numerals
Length Limit: 1 ~ 10
Default: 0000
Note: Tracker will return “SET PASSWORD OK” when received this command.
10.5 Add Manager Phone Number
MANAGERA, Current PIN,Manager Code:Manager Phone Number#
Manager Code:
Range: Positive Integer
Range limit: 1~4
Manager Phone Number:
Range: Phone number
Length Limit: 0~40
Default: <Null>
Note:
1) Tracker will return “SET MANAGERA OK” when received this command.
2) The max manager number is 4

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 13
10.6 Delete Manager Phone Number
MANAGERD, Current PIN,Manager Code#
Manager Code:
Range: Positive Integer
Range limit: 1~4
Note: Tracker will return “SET MANAGERD OK” when received this command.
10.7 List Manager Phone Number
MANAGERL, Current PIN#
Note:
1) Tracker will return “SET MANAGERL OK” when received this command.
2) All the manager phone numbers will be listed.
10.8 Google Map Search
GOOGLE, Current PIN#
Note: Tracker will return below message when received this command.
http://maps.google.com/maps?q=<Latitude>, <Longitude>
10.9 Forgot the PIN
MYSELF#
Note:
1) If the manager phone number has been set, only the manager can use “MYSELF#”.
If no manager setting, the tracker will return the IMEI and current PIN when it
received “MYSELF#” from any mobile phone.
2) This command can be used to retrieve password.
11. Optional Accessories List
Product Sku
Description
Photo for Reference
TA39
Magnet Set (4 units)
12. FOTA Notification
TOPFLYtech is committed to providing clients with the best user experience. We are offering
automatic firmware update feature for every device. This feature allows devices always having
the latest version firmware. It can save clients the time and effort of updating firmware
manually. Please note that this feature is enabled in default. If you want to turn it off, please
contact with TOPFLYtech. If this feature is disabled, the fw update only can be done by sending

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 14
upgrade command manually
13. FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.