TopflyTech TLP2-SFB User manual

TOPFLYtech TLP2-SFB Asset GPS Tracker
User Manual
20200908

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 2
Thanks for your purchasing of the high-quality GPS tracker from TOPFLYtech. Please read this user
manual carefully before installation and operation. Information in this manual is the property of
TOPFLYtech. Changes to the specifications and features in this manual may be made by
TOPFLYtech without prior notice. No part of this manual could be reproduced, copied, translated,
transmitted, or published in any form or by any means without TOPFLYtech's prior written
permission.
The tracker is using GNSS & LTE technologies and could collect device coordinates then transfer
them via LTE network to the server. It provides customer with cost-effective, efficient and safety
management. It has been widely used in commercial transportation, company vehicle fleet
management, intelligent transportation, logistics, car rental, engineering machinery, marine
transportation, animal/pet tracking and other segments.
TLP2-SFB

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 3
Contents
1. QUICK REFERENCE ..............................................................................................................................4
2. PRODUCT SPECIFICATIONS..............................................................................................................5
3. STANDARD ACCESSORIES INTRODUCTION ................................................................................6
4. LED INDICATOR ...................................................................................................................................7
5. INSTALLATION GUIDE .......................................................................................................................7
5.1 SIM CARD PRE-INSTALLATION NOTE............................................................................................................7
5.2 SIM CARD INSTALLATION AND TRACKER POWER SWITCH ...........................................................................7
5.3 INSTALLATION .................................................................................................................................................8
6. TRACKER OPERATION........................................................................................................................8
6.1 PHYSICAL POWER ON OR OFF ........................................................................................................................8
6.2 MOTION OPERATIONS....................................................................................................................................8
6.3 THE BATTERY ...................................................................................................................................................8
6.4 GET CURRENT POSITION................................................................................................................................8
7. ALARM CONFIGURATION.................................................................................................................8
7.1 ALARM SENT THROUGH NETWORK................................................................................................................8
7.2 ALARM SENT THROUGH SMS........................................................................................................................9
8. QUICK TROUBLE SHOOTING............................................................................................................9
8.1 UNABLE TO CONNECT TO THE TRACKING PLATFORM.................................................................................9
8.2 TRACKER SHOWS OFFLINE.............................................................................................................................9
8.3 UNABLE TO LOCATE .......................................................................................................................................9
8.4 POSITION DRIFT........................................................................................................................................... 10
8.5 NO COMMAND REPLY ................................................................................................................................ 10
9. WARRANTY AND STOCK ............................................................................................................... 10
10. FREQUENTLY USED COMMANDS............................................................................................ 10
10.1 APN SETTING .............................................................................................................................................. 10
10.2 SERVER SETTING........................................................................................................................................... 11
10.3 UPLOAD INTERVAL SETTING........................................................................................................................ 11
10.4 HEARTBEAT SETTING.................................................................................................................................... 12
10.5 PIN SETTING ................................................................................................................................................ 12
10.6 ADD MANAGER PHONE NUMBER.............................................................................................................. 12
10.7 DELETE MANAGER PHONE NUMBER ......................................................................................................... 13
10.8 LIST MANAGER PHONE NUMBER............................................................................................................... 13
10.9 GOOGLE MAP SEARCH................................................................................................................................ 13
10.10 FORGOT THE PIN.................................................................................................................................... 13
11. OPTIONAL ACCESSORIES LIST ................................................................................................. 13

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 4
1. Quick Reference
Attention
i. TLP1-SFB obtains power through sunlight to extend the battery life.
ii. Please make sure that the device is exposed to direct sunlight every day. This will be
very useful to extend the battery life. If the device is not charged for more than three
months, it may cause permanent damage to the internal battery.
iii. Please give the device a fully charging before installation.
iv. Only when the solar panel output voltage value is 0.3V higher than device battery
voltage value, the solar panel will start to charge the battery. Otherwise the solar
charging will stop.
v. To ensure the battery life for longer period, please be careful to set the reporting
intervals. Lower reporting rates will maintain the balance between the power
consumption and gaining (from solar panel). We usually recommend set the tracker
reporting ≥every 5 mins when moving, and ≥every 1 hour when standstill. Customer
may also contact with TOPFLYtech for further advice.
Equipment power consumption and solar panel charging current
i. The normal device power consumption is around 50mAh when the device is in working
mode without sleep.
ii. The typical charging rate of the solar panel under direct sunlight at noon (in summer) is
about 250mAh (different sunlight illumination, different charging current).
TLP2-SFB

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 5
Disclaimer: Before using this device, customers should fully understand their usage scenarios
and installation environment. TOPFLYtech will not be responsible for any lost caused by using
the device in a wrong scenario or reporting rate. It is highly recommended that customers
should contact with TOPFLYtech before deployment. We are glad to give suggestions.
Intelligent Power Management
To extend the battery life, we designed an intelligent power management algorithm. This
algorithm allows the tracker working under a lower reporting rate when battery is low. Once
the battery is charged back, the tracker will report as normal. This function is enabled in
default. Customer can disable it by command. The detail working logic is:
⚫When the battery voltage value is down to 3.45V (around 20%), then the tracker will report
at every 15 minutes when moving and every 60 minutes when standstill
(only when customer set the moving and standstill upload interval lower than 15 minutes
when moving and 60 minutes when standstill)
⚫When the battery is charged back to 3.55V (around 30%), the device will report as what
are set by customer.
FOTA (firmware over the air) Notification
TOPFLYtech is committed to providing clients with the best user experience. We are offering
automatic firmware update feature for every device. This feature allows devices always having the
latest version firmware. It can save clients the time and effort of updating firmware manually.
Please note that this feature is enabled in default. If you want to turn it off, please contact with
TOPFLYtech. If this feature is disabled, the fw update only can be done by sending upgrade
command manually.
2. Product Specifications
Network Specifications
Data Transmission eMTC: Max. 300Kbps (DL), Max. 375Kbps (UL)
NB1: Max. 32Kbps (DL), Max. 70Kbps (UL)
EDGE: Max. 296Kbps (DL), Max. 236.8Kbps (UL)
GPRS: Max. 107Kbps (DL), Max. 85.6Kbps (UL)
GNSS Specifications
GNSS Chipset Qualcomm Gen 8C GNSS receiver
GNSS System GPS+Glonass+Galileo+Beidou
Receiver type: 33 tracking / 99 acquisitions- channel GNSS
receiver

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 6
Sensitivity Cold start: -149 dBm
Tracking: -163 dBm
Position Accuracy in open sky (CEP-50) < 2m
Standalone TTFF Cold start: < 29s
Warm start: < 27s
Hot start: < 1s
Interfaces
Charging and Data Transmission 4 Pin port with magnet
Network, GNSS Antenna Internal only
Indicator LED Network, GNSS and Battery
FOTA Yes
Physical Power Switch 1
Light Sensor 1 back light sensor
Temperature Sensor 1 temperature sensor
BLE 5.0 Yes
General Specifications
Waterproof IP67
Dimensions 85mm*185mm*31 mm (3.35” *7.28” *1.22”)
Weight 370g (13oz)
Battery Rechargeable Li-Polymer 9600 mAh/ 3.6V
Standby Time
(without solar charging, 2 hours active
tracking per day)
10 minutes reporting: 320 Days
5 minutes reporting: 170 Days
1 minute reporting: 68 Days
Charging & Data Communication Magnetic USB cable
(recommend using 5V 1A adaptor, 20 hours
charging)
Operating Temperature -25℃ ~ +70℃ (-13°F ~ 158°F)
Mounting Magnet/Screw
Air Interface Protocol
Transmit Protocol TCP, UDP, MQTT, SMS
Data Security & Encryption Option MD5/ AES256
BLE Accessory Support Yes
Scheduled Timing/angle/distance Report Report position and status at preset intervals
Geo-fence Support up to 64 internal geo-fence regions
Alarms Support up to 31 types of alarm
(refer 7. Alarm Configuration)
3. Standard Accessories Introduction
USB cable

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 7
4. LED indicator
Note: Indicator lights will go out automatically after the tracker turns on for 70 seconds without
connecting to the external power via USB cable.
5. Installation Guide
5.1 SIM card pre-installation note
5.1.1 SIM card data service should be enabled.
5.1.2 If SIM card is locked via PIN, please unlock it first.
5.1.3 Ensure there is sufficient balance in the SIM card.
5.2 SIM card installation and tracker power switch
5.2.1 Open the tracker SIM card slot cover with the screwdriver.
5.2.2 Insert the SIM card with a little push. Turn the power switch from off to on.
5.2.3 Put the cover back and use screwdriver to fix the cover tightly.

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 8
5.3 Installation
5.3.1 Away from emission source such as all kinds of sensors, burglar alarm and other
communication devices.
6. Tracker Operation
6.1 Physical power on or off
6.1.1 Turn the power switch to on or off position.
6.1.2 Physical power off is recommended when the tracker is stored in the warehouse.
6.2 Motion operations
Hold the tracker and keep the indicator LED side towards the sky. Use normal speed to
turn it over 180°(the solar panel side towards the sky) then recover. This is called one-
time standard turning. By repeating the standard turning 3 times, the tracker will show
GNSS, network and battery status through indicator LED. It only works when physical
power switch at on position
6.3 The battery
6.3.1 Place the tracker solar panel side on the desk
6.3.2 Recommend connecting the device to a 5V 1A (cellphone) adaptor through
magnet USB cable for 20 hours charging to make sure the battery is fully charged.
6.3.3 Customer also can connect the tracker to other USB connectors. But lower current
output will cause longer charging time.
6.3.4 When the battery voltage value drops to 3.3V, usually a battery charging is
needed to avoid unexpected shutdown due to low power. If the battery runs out
completely, only when the battery is charged to 3.32V, the device will power on
again.
6.4 Get Current Position
6.4.1 SMS Query (only when the device in working mode and registered on the network)
Device default PIN is 0000. Send a location inquiry SMS command (google,0000#)
to the tracker. The location information will be sent back through SMS (the tracker
SIM card must support receiving and sending SMS first).
6.4.2 Platform Query
Connect your tracker to the tracking platform then check the real-time position
online. (Additional tracking service charge may happen. Contact with your service
provider to get more details)
7. Alarm Configuration
7.1 Alarm sent through network
7.1.1 alarm_set,0000,a,b,0,0,#
7.1.2 0000 is device default PIN
7.1.3 a=alarm code, value from 1 to 31

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 9
Alarm Code
Description
Alarm Code
Description
1
Device removal (VS alarm 21)
16
Start moving (VS alarm 17)
5
Start falling (VS alarm 24)
17
Stop moving
6
Low battery (Vs alarm 7)
18
Idle start (VS alarm 19)
7
Battery recover
19
Idle stop
8
Device high temperature (VS alarm 25)
21
Device mounted
9
Vibration start (VS alarm 26)
24
Stop falling
10
Collision (VS alarm 27)
25
Device high temperature disappear
11
Tilt start (VS alarm 28)
26
Vibration stop
12
USB cable connected (VS alarm 13)
27
Collision stop
13
USB cable disconnected
28
Tilt stop
14
Enter geofence (VS alarm 15)
30
Device low temperature (VS alarm 31)
15
Leave geofence
31
Device low temperature disappear
7.1.4 b=enable or disable, value is 0 (disable) or 1 (enable)
7.2 Alarm sent through SMS
Alarm also can be sent through SMS. But the tracker SIM card must support SMS function
first. Then it needs customer set manager cellphone number. Please refer the frequently
used commands part to get further information. Related commands: managera,
managerd, manager.
8. Quick Trouble Shooting
8.1 Unable to Connect to the Tracking Platform
8.1.1 Check the APN and IP settings.
8.1.2 Check the SIM card data service whether enabled.
8.1.3 Make sure there is no limitation or already added server IP to the SIM card IP
white list when using a M2M SIM card.
8.1.4 Check the balance/data of the SIM card.
8.2 Tracker Shows Offline
8.2.1 Check the battery remaining power
8.2.2 Check if the device entered into network blind area.
8.2.3 Check the SIM card balance.
8.2.4 If the connection lost happens on the last several days of the month, check
whether the network service is terminated by carrier because of exceeding the
max data usage volume.
8.3 Unable to Locate
8.3.1 The device may shield by metallic things.
8.3.2 The device may enter into an area with no satellite signal coverage.

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 10
(underground, building, etc)
8.4 Position Drift
In an area with poor GNSS signal (like the areas with lots of high buildings), position drift
may happen. When the device moves to open area, the drift will no longer exist.
8.5 No Command Reply
8.5.1 Check the command format. Make sure it’s correct.
8.5.2 The device may be in network blind area.
8.5.3 Ensure the SIM card is properly inserted.
9. Warranty and Stock
The device standard warranty period is 12 months starting from the date of purchasing. If the
device will be stored for a long time, please connect it to the external power and recharge the
internal battery (20 hours) every 3 months. It will be helpful to extend the internal battery life.
10. Frequently Used Commands
Commands are not case-sensitive and can be sent via mobile phone. The content is separated
by comma and ends with #. When set successfully, the tracker will return OK and execute it.
Otherwise there will be no message returned.
Function
Command Format
APN Setting
APN ,Current PIN , APN Name , Username , Password #
Server Setting
IP ,Current PIN , Server Domain Name or IP , Port Number #
Upload Interval Setting
TIMER, Current PIN , Upload Time(ACC on) : Upload Time(ACC
off) : Angle Compensation : Distance Compensation #
Heartbeat Setting
HBT, Current PIN , Heartbeat Interval #
PIN Setting
PASSWORD, Current PIN , New PIN #
Add Manager Phone Number
MANAGERA, Current PIN , Manager Code : Manager Phone Number #
Delete Manager Phone Number
MANAGERD, Current PIN , Manager Code #
List Manager Phone Number
MANAGERL, Current PIN #
Google Map Search
GOOGLE, Current PIN #
Forgot the PIN
MYSELF#
10.1 APN Setting
APN, Current PIN,APN Name,Username,Password#

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 11
APN Name:
Range: APN of service provider
Length Limit: 1~32
Username:
Range: Letters and Numerals
Length Limit: 0~32
Password:
Range: Letters and Numerals
Length Limit: 0~32
Note:
1) Tracker will return “SET APN OK” when received this command.
2) If there is no Username and Password, the SMS setting is:
APN,Current PIN,APN Name,,#
3) If there is no APN PIN, the SMS setting is:
APN,Current PIN,APN Name,Username,#
10.2 Server Setting
IP, Current PIN,Server Domain Name or IP,Port Number#
Server Domain Name or IP:
Range: Letters, Numerals and Symbols
Length Limit: 1~128
Port Number:
Range: Positive Integer
Length Limit: 0~65535
Note: Tracker will return “SET IP OK” when received this command.
10.3 Upload Interval Setting
TIMER, Current PIN,Upload Time(ACC on):Upload Time(ACC off):Angle Compensation:
Distance Compensation#
Upload Time (ACC on):
Range: Positive Integer
Range Limit: 0, 3~65535 second
Default: 60
Upload Time (ACC off):
Range: Positive Integer

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 12
Range Limit: 0, 3~ 4294967295 second
Default: 240
Angle Compensation:
Range: Positive Integer
Range Limit: 0~90 degrees
Default: 30 degrees
Distance Compensation:
Range: Positive Integer
Range Limit: 0 ~ 65535 meters
Default: 0 meters
Note: Tracker will return “SET TIMER OK” when received this command.
10.4 Heartbeat Setting
HBT, Current PIN,Heartbeat Interval#
Heartbeat Interval:
Range: Positive Integer
Range Limit: 1 ~ 255 minutes
Default: 30 minutes
Note: Tracker will return “SET HBT OK” when received this command.
10.5 PIN Setting
PASSWORD, Current PIN,New PIN#
PIN:
Range: Letters and Numerals
Length Limit: 1 ~ 10
Default: 0000
Note: Tracker will return “SET PASSWORD OK” when received this command.
10.6 Add Manager Phone Number
MANAGERA, Current PIN,Manager Code:Manager Phone Number#
Manager Code:
Range: Positive Integer
Range limit: 1~4
Manager Phone Number:
Range: Phone number

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 13
Length Limit: 0~40
Default: <Null>
Note:
1) Tracker will return “SET MANAGERA OK” when received this command.
2) The max manager number is 4
10.7 Delete Manager Phone Number
MANAGERD, Current PIN,Manager Code#
Manager Code:
Range: Positive Integer
Range limit: 1~4
Note: Tracker will return “SET MANAGERD OK” when received this command.
10.8 List Manager Phone Number
MANAGERL, Current PIN#
Note:
1) Tracker will return “SET MANAGERL OK” when received this command.
2) All the manager phone numbers will be listed.
10.9 Google Map Search
GOOGLE, Current PIN#
Note: Tracker will return below message when received this command.
http://maps.google.com/maps?q=<Latitude>, <Longitude>
10.10 Forgot the PIN
MYSELF#
Note:
1) If the manager phone number has been set, only the manager can use “MYSELF#”.
If no manager setting, the tracker will return the IMEI and current PIN when it
received “MYSELF#” from any mobile phone.
2) This command can be used to retrieve password.
11. Optional Accessories List
Product Sku
Description
Photo for Reference
TSTH1-B
BLE 5.0 Wireless Temperature
and Humidity Sensor

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 14
TSDT1-B
BLE 5.0 Wireless Door and
Temperature Sensor
TSR1-B
BLE 5.0 Wireless Relay
TA39
Magnet Set (4 units)
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.

Shenzhen TOPFLYtech Co., Limited. All Rights Reserved 15
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator& your body.