Topp Music Gear TPS BETA1152A User manual
PRO-CONCERT LEVEL PASSIVE / ACTIVE AUDIO ENCLOSURES
User’s Manual
TPS BETA1152/1152A TPS BETA2152/2152A
TPS BETA15/18/218 SUB TPS BETA15A/18A SUB
l
l
Safety Related Symbols
Protective Ground
Before turning the unit ON, make sure that it is
connected to Ground. This is to prevent the risk of
electric shock.
Never cut internal or external Ground wires. Like wise,
never remove Ground wiring from the Protective
Ground Terminal.
Operating Conditions
Always install in accordance with the manufacturer's
instructions.
To avoid the risk of electric shock and damage, do not
subject this product to any liquid/rain or moisture.
Do not use this product when in close proximity to
water.
Do not install this product near any direct heat source.
Do not block areas of ventilation. Failure to do so
could result in fire.
Keep product away from naked flames.
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions
Follow all instructions
Keep these instructions. Do not discard.
Heed all warnings.
Only use attachments / accessories specified by the
manufacturer.
Power Cord and Plug
Do not tamper with the power cord or plug. These are
designed for your safety.
Do not remove Ground connections!
If the plug does not fit your AC out let seek advice
from a qualified electrician.
Protect the power cord and plug from any physical
stress to avoid risk of electric shock.
Do not place heavy objects on the power cord. This
could cause electric shock or fire.
Cleaning
When required, either blow off dust from the product
or use a dry cloth.
Do not use any solvents such as Benzol or Alcohol.
For safety, keep product clean and free from dust.
Servicing
Refer all servicing to qualified service personnel only.
Do not perform any servicing other than those
instructions contained within the User's Manual.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2TOPP PRO
MUSIC GEAR
PORTABLE
CART WARNING
Carts and stands - The
component should be used
only with a cart or stand
that is recommended by
the manufacturer.
A component and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the component and
cart combination to
overturn.
This symbol, wherever used, alerts you to the presence
of un-insulated and dangerous voltages within the
product enclosure. These are voltages that may be
sufficient to constitute the risk of electric shock or
death.
This symbol, wherever used, alerts you to important
operating and maintenance instructions.
Please read.
Protective Ground Terminal
AC mains (Alternating Current)
AC mains (Alternating Current)
Denotes the product is turned on.
Denotes the product is turned off.
WARNING
Describes precautions that should be observed to
prevent the possibility of death or injury to the user.
CAUTION
Describes precautions that should be observed to
prevent damage to the product.
Disposing of this product should not be placed in
municipal waste but rather in a separate collection.
WARNING
Power Supply
Ensure that them a inssource voltage (AC outlet)
matches the voltage rating of the product. Failure to
do so could result in damage to the product and
possibly the user. Unplug the product before electrical
storms occur and when unused for long periods of
time to reduce the risk of electric shock or fire.
External Connection
Always use proper ready-made insulated mains
cabling (power cord). Failure to do so could result in
shock/death or fire. If in doubt, seek advice from a
registered electrician.
Do Not Remove Any Covers
Within the product are areas where high voltages may
present. To reduce the risk of electric shock do not
remove any covers unless the AC mains power cord is
removed. Covers should be removed by qualified
service personnel only.
No user serviceable parts inside.
Fuse
To prevent fire and damage to the product, use only
the recommended fuse type as indicated in this
manual. Do not short-circuit the fuse holder. Before
replacing the fuse, make sure that the product is OFF
and disconnected from the AC outlet.
3
Table of Contents
Don’t forget to visit our website at www.topppro.com
for more information about this and other Topp Pro products.
4
4
4
5
10
12
13
18
20
1. PROLOGUE
2. INSTALLATION TIPS
3. USEFULL DATA
4. CONNECTING DIAGRAM
For Passive Speaker Cabinet
For Passive Subwoofer & Satellite Speakers
For Active Speaker Cabinet
For Active Subwoofer & Satellite Speakers
5. CONNECTING PLATE
For Passive Series Speaker
For Active Full-range Speaker
For Active Subwoofer Speaker
6. WIRE CONNECTIONS
7. TECHNICAL SPECIFICATIONS
8. BLOCK DIAHGRAM
9. GUARANTEE
TOPP PRO
MUSIC GEAR
Safety Related Symbols
Protective Ground
Before turning the unit ON, make sure that it is
connected to Ground. This is to prevent the risk of
electric shock.
Never cut internal or external Ground wires. Like wise,
never remove Ground wiring from the Protective
Ground Terminal.
Operating Conditions
Always install in accordance with the manufacturer's
instructions.
To avoid the risk of electric shock and damage, do not
subject this product to any liquid/rain or moisture.
Do not use this product when in close proximity to
water.
Do not install this product near any direct heat source.
Do not block areas of ventilation. Failure to do so
could result in fire.
Keep product away from naked flames.
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions
Follow all instructions
Keep these instructions. Do not discard.
Heed all warnings.
Only use attachments / accessories specified by the
manufacturer.
Power Cord and Plug
Do not tamper with the power cord or plug. These are
designed for your safety.
Do not remove Ground connections!
If the plug does not fit your AC out let seek advice
from a qualified electrician.
Protect the power cord and plug from any physical
stress to avoid risk of electric shock.
Do not place heavy objects on the power cord. This
could cause electric shock or fire.
Cleaning
When required, either blow off dust from the product
or use a dry cloth.
Do not use any solvents such as Benzol or Alcohol.
For safety, keep product clean and free from dust.
Servicing
Refer all servicing to qualified service personnel only.
Do not perform any servicing other than those
instructions contained within the User's Manual.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2TOPP PRO
MUSIC GEAR
PORTABLE
CART WARNING
Carts and stands - The
component should be used
only with a cart or stand
that is recommended by
the manufacturer.
A component and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the component and
cart combination to
overturn.
This symbol, wherever used, alerts you to the presence
of un-insulated and dangerous voltages within the
product enclosure. These are voltages that may be
sufficient to constitute the risk of electric shock or
death.
This symbol, wherever used, alerts you to important
operating and maintenance instructions.
Please read.
Protective Ground Terminal
AC mains (Alternating Current)
AC mains (Alternating Current)
Denotes the product is turned on.
Denotes the product is turned off.
WARNING
Describes precautions that should be observed to
prevent the possibility of death or injury to the user.
CAUTION
Describes precautions that should be observed to
prevent damage to the product.
Disposing of this product should not be placed in
municipal waste but rather in a separate collection.
WARNING
Power Supply
Ensure that them a inssource voltage (AC outlet)
matches the voltage rating of the product. Failure to
do so could result in damage to the product and
possibly the user. Unplug the product before electrical
storms occur and when unused for long periods of
time to reduce the risk of electric shock or fire.
External Connection
Always use proper ready-made insulated mains
cabling (power cord). Failure to do so could result in
shock/death or fire. If in doubt, seek advice from a
registered electrician.
Do Not Remove Any Covers
Within the product are areas where high voltages may
present. To reduce the risk of electric shock do not
remove any covers unless the AC mains power cord is
removed. Covers should be removed by qualified
service personnel only.
No user serviceable parts inside.
Fuse
To prevent fire and damage to the product, use only
the recommended fuse type as indicated in this
manual. Do not short-circuit the fuse holder. Before
replacing the fuse, make sure that the product is OFF
and disconnected from the AC outlet.
3
Table of Contents
Don’t forget to visit our website at www.topppro.com
for more information about this and other Topp Pro products.
4
4
4
5
10
12
13
18
20
1. PROLOGUE
2. INSTALLATION TIPS
3. USEFULL DATA
4. CONNECTING DIAGRAM
For Passive Speaker Cabinet
For Passive Subwoofer & Satellite Speakers
For Active Speaker Cabinet
For Active Subwoofer & Satellite Speakers
5. CONNECTING PLATE
For Passive Series Speaker
For Active Full-range Speaker
For Active Subwoofer Speaker
6. WIRE CONNECTIONS
7. TECHNICAL SPECIFICATIONS
8. BLOCK DIAHGRAM
9. GUARANTEE
TOPP PRO
MUSIC GEAR
Thank you for purchasing TOPP PRO MUSIC GEAR products BETA series speaker cabinet.
The cabinets are all plywood construction with our DURAPRO paint finish. The
components have been matched to offer the highest quality achievable.
The 3" Compression Driver and woofer reinforcement provided an excellent performance.
The BETA series speaker cabinets can be used for all type of applicatio nincluding but not
limit to churches, conferences room, disco and by live performance groups.
We believe with these features combination, the BETA series speaker cabinets not only
looks great, but also provides a perfect performance.
Speakers should be placed in a position that allows for unobstructed sound protection.
In many instances is beneficial for speakers to be elevated on tripod stands to achieve
maximum dispersion and reach.
Use professional advice or service when hanging and installing speakers. Please takes
precautions to secure the speakers to prevent them from falling and hurting someone,
secure the speaker could also prevent you from damaging the cabinet or its
components.
Use quality cables. Using quality cables ensure best possible sound.
For best results of the BETA passive cabinets, you can match the speaker to a good
amplifier that match the wattage and impedance of your speakers. Proper amplification
power result in good quality audio and longer component life. Check out the power
requirement for your cabinet. And match your BETA passive cabinets to a good mixer.
(Please refer to FIG. 1)
In some applications, matching the BETA passive cabinet with BETA subwoofers to
achieve bass reinforcement. (Please refer to FIG. 2 & FIG. 3)
For the BETA active cabinets there are no need amplifier so you can match them with a
good mixer.
Avoid pointing microphone directly at an amplified speaker; doing so could cause feed
back possibly damaging speaker components and your hearing.
(Please refer to FIG. 4 & FIG. 5)
Please write your serial number here for future reference.
4
Introduction
Usefull Tips
Serial Number:
Date of Purchase:
Purchased at:
Usefull Data
1
2
3
l
l
l
l
l
l
l
TOPP PRO
MUSIC GEAR 5
Connecting Diagram 4
Make your initial connections with all the equipment powered off, and ensure that all the main
volume controls are turned completely down.
For Passive Full-range Speaker Cabinet
1) Connect one side of the speaker cable to the Output CH A / CH B ot Binding Post of your stereo
power amplifier and the other side to the Input socket of your speaker cabinet.
2) Complete other connections as illustrated.
3) Turn on your mixer first, then the stereo power amplifier.
4) Turn up the volume controls of your amplifier to about 70%.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using, turn off your stereo power amplifier first, then the mixer.
TOPP PRO
MUSIC GEAR
TPS BETA 1152 TPS BETA1152
FIG.1
TPS BETA 2152 TPS BETA 2152
Thank you for purchasing TOPP PRO MUSIC GEAR products BETA series speaker cabinet.
The cabinets are all plywood construction with our DURAPRO paint finish. The
components have been matched to offer the highest quality achievable.
The 3" Compression Driver and woofer reinforcement provided an excellent performance.
The BETA series speaker cabinets can be used for all type of applicatio nincluding but not
limit to churches, conferences room, disco and by live performance groups.
We believe with these features combination, the BETA series speaker cabinets not only
looks great, but also provides a perfect performance.
Speakers should be placed in a position that allows for unobstructed sound protection.
In many instances is beneficial for speakers to be elevated on tripod stands to achieve
maximum dispersion and reach.
Use professional advice or service when hanging and installing speakers. Please takes
precautions to secure the speakers to prevent them from falling and hurting someone,
secure the speaker could also prevent you from damaging the cabinet or its
components.
Use quality cables. Using quality cables ensure best possible sound.
For best results of the BETA passive cabinets, you can match the speaker to a good
amplifier that match the wattage and impedance of your speakers. Proper amplification
power result in good quality audio and longer component life. Check out the power
requirement for your cabinet. And match your BETA passive cabinets to a good mixer.
(Please refer to FIG. 1)
In some applications, matching the BETA passive cabinet with BETA subwoofers to
achieve bass reinforcement. (Please refer to FIG. 2 & FIG. 3)
For the BETA active cabinets there are no need amplifier so you can match them with a
good mixer.
Avoid pointing microphone directly at an amplified speaker; doing so could cause feed
back possibly damaging speaker components and your hearing.
(Please refer to FIG. 4 & FIG. 5)
Please write your serial number here for future reference.
4
Introduction
Usefull Tips
Serial Number:
Date of Purchase:
Purchased at:
Usefull Data
1
2
3
l
l
l
l
l
l
l
TOPP PRO
MUSIC GEAR 5
Connecting Diagram 4
Make your initial connections with all the equipment powered off, and ensure that all the main
volume controls are turned completely down.
For Passive Full-range Speaker Cabinet
1) Connect one side of the speaker cable to the Output CH A / CH B ot Binding Post of your stereo
power amplifier and the other side to the Input socket of your speaker cabinet.
2) Complete other connections as illustrated.
3) Turn on your mixer first, then the stereo power amplifier.
4) Turn up the volume controls of your amplifier to about 70%.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using, turn off your stereo power amplifier first, then the mixer.
TOPP PRO
MUSIC GEAR
TPS BETA 1152 TPS BETA1152
FIG.1
TPS BETA 2152 TPS BETA 2152
46
4Connecting Diagram
TOPP PRO
MUSIC GEAR
For Passive Satellite Matching with passive Subwoofer Speakers
1) Connect one side of the speaker cable to the Output CH A / CH B ot Binding Post of your stereo
power amplifier and the other side to the Input socket of your subwoofer, do the same
connection on your second power amplifier and the 2-way full-range passive speakers with a
second speaker cable.
2) Complete other connections as illustrated.
3) Turn on your mixer first, then the stereo power amplifier.
4) Turn up the volume controls of your amplifier to about 70%.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using, turn off your stereo power amplifier first, then the mixer.
FIG.3
Crossover
Equalizer
TPS BETA15 SUB
TPS BETA1152 TPS BETA1152
TPS BETA15 SUB
57
4
Connecting Diagram
TOPP PRO
MUSIC GEAR
For Passive Subwoofer & 2-way full range Speakers
FIG.3
Equalizer
TPS BETA2152
TPS BETA2152
TPS BETA218 SUBTPS BETA218 SUB
46
4Connecting Diagram
TOPP PRO
MUSIC GEAR
For Passive Satellite Matching with passive Subwoofer Speakers
1) Connect one side of the speaker cable to the Output CH A / CH B ot Binding Post of your stereo
power amplifier and the other side to the Input socket of your subwoofer, do the same
connection on your second power amplifier and the 2-way full-range passive speakers with a
second speaker cable.
2) Complete other connections as illustrated.
3) Turn on your mixer first, then the stereo power amplifier.
4) Turn up the volume controls of your amplifier to about 70%.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using, turn off your stereo power amplifier first, then the mixer.
FIG.3
Crossover
Equalizer
TPS BETA15 SUB
TPS BETA1152 TPS BETA1152
TPS BETA15 SUB
57
4
Connecting Diagram
TOPP PRO
MUSIC GEAR
For Passive Subwoofer & 2-way full range Speakers
FIG.3
Equalizer
TPS BETA2152
TPS BETA2152
TPS BETA218 SUBTPS BETA218 SUB
48 TOPP PRO
MUSIC GEAR
4Connecting Diagram
For active Full-range Speaker Cabinet
1) Connect one side of the signal cable at your audio mixer into Output Left/Right (with Stereo-Jack
or XLR) and the other side of the cable into the Line Input (COMBO) of your active speaker
cabinet (with Stereo-Jack or XLR).
2) Connect the power cord to mains.
3) Turn on your mixer first, then the active speaker cabinets.
4) Turn up the volume control of the active speaker cabinets.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using ,turn off your active speaker cabinets first, then the mixer.
speaker cable
Tripod
Mount
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
Tripod
Mount
speaker cable
Power Cord
TPS BETA1152A
speaker cable
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
speaker cable
Power Cord Power Cord
TPS BETA2152A
FIG.4
Power Cord
TPS BETA1152A
TPS BETA2152A
For Active Satellite Matching with Active Subwoofer Speakers
1) Connect one side of the signal cable at your audio mixer in to Output Left/Right (with Stereo-Jack
or XLR) and the other side of the cable into the Line Input (COMBO) of your active subwoofer;
with the second cable connect the left output of subwoofer (with Stereo/Mono-Jack or XLR) to
the Line Input (COMBO) of the active satellite. (
2) Connect the power cord to mains.
3) Turn on your mixer first, then the active speaker cabinets.
4) Turn up the volume control of the active speaker cabinets.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using ,turn off your active speaker cabinets first, then the mixer.
Stereo-Jack or XLR)
TPS BETA15A- SUB
TPS BETA15A- SUB
TPS BETA1152A TPS BETA1152A
FIG.5
59
4
Connecting Diagram
TOPP PRO
MUSIC GEAR
48 TOPP PRO
MUSIC GEAR
4Connecting Diagram
For active Full-range Speaker Cabinet
1) Connect one side of the signal cable at your audio mixer into Output Left/Right (with Stereo-Jack
or XLR) and the other side of the cable into the Line Input (COMBO) of your active speaker
cabinet (with Stereo-Jack or XLR).
2) Connect the power cord to mains.
3) Turn on your mixer first, then the active speaker cabinets.
4) Turn up the volume control of the active speaker cabinets.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using ,turn off your active speaker cabinets first, then the mixer.
speaker cable
Tripod
Mount
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
Tripod
Mount
speaker cable
Power Cord
TPS BETA1152A
speaker cable
Left
Main Mix
Output
Right
Main Mix
Output
Mixer
speaker cable
Power Cord Power Cord
TPS BETA2152A
FIG.4
Power Cord
TPS BETA1152A
TPS BETA2152A
For Active Satellite Matching with Active Subwoofer Speakers
1) Connect one side of the signal cable at your audio mixer in to Output Left/Right (with Stereo-Jack
or XLR) and the other side of the cable into the Line Input (COMBO) of your active subwoofer;
with the second cable connect the left output of subwoofer (with Stereo/Mono-Jack or XLR) to
the Line Input (COMBO) of the active satellite. (
2) Connect the power cord to mains.
3) Turn on your mixer first, then the active speaker cabinets.
4) Turn up the volume control of the active speaker cabinets.
5) Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control
to manipulate the output level.
6) After using ,turn off your active speaker cabinets first, then the mixer.
Stereo-Jack or XLR)
TPS BETA15A- SUB
TPS BETA15A- SUB
TPS BETA1152A TPS BETA1152A
FIG.5
59
4
Connecting Diagram
TOPP PRO
MUSIC GEAR
410 TOPP PRO
MUSIC GEAR
5Connecting Plate
For Passive Full-range series Speaker (TPS BETA 1152 / 2152)
With the mode switch (3) set to "Full Range" position:
(1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2-2
not connected).
(2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +1/-1 connected; +2-2
not connected).
With the mode switch (3) set to “BI-AMP” position:
(1) INPUT: Receive the power coming from two separate amplifier channels SPK +1/-1 connect to
low frequency; SPK +2-2 connect to high frequency.
(2) THRU: Direct LINK for connect in parallel a second TPS BETA 1152 speaker cabinet.
For Passive Subwoofer series Speaker (TPS BETA 15 / 18 / 218 SUB)
(1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2-2
not connected).
(2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +1/-1 connected; +2-2
not connected).
For Active series Full-range Speaker (TPS BETA 1152A / 2152A)
(1) LINE IN on COMBO connector
(2) Link on XLR connector
(3) SIGNAL limit, Red LED, indicate ON status
(4) Ground Switch
(5) VOLUME main power amplifier control
(6) Input AC power socket with main fuse
(7) Bi-polar main power switch
(8) Presets selector (MUSIC-FLAT-VOCAL)
(9) AC INPUT voltage selector
For Active Subwoofer Speaker (TPSBETA15A / 18A-SUB)
(1) LINE IN on COMBO connector
(2) LINE OUT on XLR connector
(3) SIGNAL COMP, Red LED, indicate ON status
(4) Compressor / Limit switch
(5) Ground Switch
(6) Main volume control
(7) Input AC power socket with main fuse
(8) Bi-polar main power switch
(9) AC INPUT voltage selector
(10) Phase switch
511
TOPP PRO
MUSIC GEAR
5
Connecting Plate
CAUTION:
REPLACE FUSE ONLYWITH SAME AND RATEDTYPE!
SIGNAL
LIMIT
BAL
LINKINPUT
VOLUME
MAX MIN
MIN MAX
L
I
N
E
M
I
C
ON
OFF
SHIELD
220V110V
POWER CONSUMPTION:780W
AC INPUT:
110-127V 50/60Hz T8AL/250V~
220-240V 50/60Hz~T4AL/250V
TPS BETA1152A
POWER
MUSIC VOCAL
FLAT
1
3
2
B
(7) (6)
(9)
(4)
(5)
(2)
(1)
(3)(8)
(5)(3)(2) ( )
1
3
2B1
3
2B
CAUTION:
ISO9001 Certitied & RoHS Compliant
REPLACE FUSE ONLYWITH SAME AND RATEDTYPE!
OFF
LEFT INRIGHT IN
LINKLINK
BAL +4dB
220V110V
POWER CONSUMPTION:800W
AC INPUT:AC INPUT:
110-127V 50/60Hz T10AL/250V~
220-240V 50/60Hz~T5AL/250V
POWER
180
0
TPS BETA 18A-SUB
ON
VOLUME
+6dB
SIGNAL
COMP
0
(7)
(9)
(1)
(6)
(8)
10
(4)
ON
OFF
COMP. / LIM.
410 TOPP PRO
MUSIC GEAR
5Connecting Plate
For Passive Full-range series Speaker (TPS BETA 1152 / 2152)
With the mode switch (3) set to "Full Range" position:
(1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2-2
not connected).
(2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +1/-1 connected; +2-2
not connected).
With the mode switch (3) set to “BI-AMP” position:
(1) INPUT: Receive the power coming from two separate amplifier channels SPK +1/-1 connect to
low frequency; SPK +2-2 connect to high frequency.
(2) THRU: Direct LINK for connect in parallel a second TPS BETA 1152 speaker cabinet.
For Passive Subwoofer series Speaker (TPS BETA 15 / 18 / 218 SUB)
(1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2-2
not connected).
(2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +1/-1 connected; +2-2
not connected).
For Active series Full-range Speaker (TPS BETA 1152A / 2152A)
(1) LINE IN on COMBO connector
(2) Link on XLR connector
(3) SIGNAL limit, Red LED, indicate ON status
(4) Ground Switch
(5) VOLUME main power amplifier control
(6) Input AC power socket with main fuse
(7) Bi-polar main power switch
(8) Presets selector (MUSIC-FLAT-VOCAL)
(9) AC INPUT voltage selector
For Active Subwoofer Speaker (TPSBETA15A / 18A-SUB)
(1) LINE IN on COMBO connector
(2) LINE OUT on XLR connector
(3) SIGNAL COMP, Red LED, indicate ON status
(4) Compressor / Limit switch
(5) Ground Switch
(6) Main volume control
(7) Input AC power socket with main fuse
(8) Bi-polar main power switch
(9) AC INPUT voltage selector
(10) Phase switch
511
TOPP PRO
MUSIC GEAR
5
Connecting Plate
CAUTION:
REPLACE FUSE ONLYWITH SAME AND RATEDTYPE!
SIGNAL
LIMIT
BAL
LINKINPUT
VOLUME
MAX MIN
MIN MAX
L
I
N
E
M
I
C
ON
OFF
SHIELD
220V110V
POWER CONSUMPTION:780W
AC INPUT:
110-127V 50/60Hz T8AL/250V~
220-240V 50/60Hz~T4AL/250V
TPS BETA1152A
POWER
MUSIC VOCAL
FLAT
1
3
2
B
(7) (6)
(9)
(4)
(5)
(2)
(1)
(3)(8)
(5)(3)(2) ( )
1
3
2B1
3
2B
CAUTION:
ISO9001 Certitied & RoHS Compliant
REPLACE FUSE ONLYWITH SAME AND RATEDTYPE!
OFF
LEFT INRIGHT IN
LINKLINK
BAL +4dB
220V110V
POWER CONSUMPTION:800W
AC INPUT:AC INPUT:
110-127V 50/60Hz T10AL/250V~
220-240V 50/60Hz~T5AL/250V
POWER
180
0
TPS BETA 18A-SUB
ON
VOLUME
+6dB
SIGNAL
COMP
0
(7)
(9)
(1)
(6)
(8)
10
(4)
ON
OFF
COMP. / LIM.
412
For Passive Speaker Cabinets
Please use only the power connectors to make connections with other signal source
equipment for the passive speaker cabinets. The power connector has four terminals: 1+,
2-, 2+, 2-.
For TPS BETA 1152 / 2152, with the “MODE SWITCH” on BI-AMP position, 1+ / 1- used to
connect with the Low Frequency, 2+ / 2- used to connect with High Frequency.
For Active Speaker Cabinets
As to these circumstances, audio connections is mostly intended for the signal flow, so,
determine the wire configuration according to your real application system and its
connecting facility. Normally, you have the following choices:
For TPS BETA 1152 / 2152, with the “MODE SWITCH” on Full Range position & TPS BETA
SUB Series, 1+ / 1- used to connect the Speaker + / Speaker -, 2+ / 2- not used.
6
TOPP PRO
MUSIC GEAR
Wire Connections
513
TOPP PRO
MUSIC GEAR
7
TECHNICAL SPECIFICATIONS
Model
System type
Crossover Modes
Crossover Frequency
Power Rated
Nominal Impedance
Sensitivity (1W,1m)
Maximum SPL 1mt
Frequency Response
Low-Frequency Device
High-Frequency Device
HornCoverage (Hº x Vº)
High Frequency Protection
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
TPS BETA 1152
2-Way Vented Box
Bi-amp / Full-range, externally switchable
1.8 kHz
LF/Full-range: 8 ohms / HF: 8 ohms
Passive: 99dB / LF: 99.5dB / HF: 108dB
125dB (Calculated)
38Hz ~ 18KHz (-6dB)
15” 402mm - 3" Voice Coil
2" Compression Driver - 3” Voice Coil
90º x 60º
Electronic Dynamic Protection (both two modes)
2 x SPK4 (Pin1+; Pin1-; Pin2+; Pin2-)
Textured black paint-black perforated Steel-12xM8 Flying points
867 x 497 x 600mm (34.13" x 19.57" x 23.62")
79.81 lbs / 36.2 kg
14.67 CFT
LF/Full-range: 400W Continuous 800W Peak
HF: 100W Continuous 200W Peak / LF/Full-range: 8 ohms
Ø
Model
System Type
Amplifier Continuous Power
Amplifier Program Power
Sensitivity at 1mt
Max SPL at 1mt
Frequency Response
Input Sensitivity
Input Impedance
Horn Coverage (Hº x Vº)
Connectors
Subsonic Filter
Protections
External Control
Power Supply
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
TPS BETA 1152A
2-Way Bi-amp Active Vented Box
LOW: 500 W / HIGH: 150W
LOW: 1000 W / HIGH: 300W
997 dB
126 dB
38Hz - 18kHz (-6db)
Line 0dB
30K ohms Balanced - 15K ohms Unbalanced
90º x 60º
Combo input XLR / Link / Line - Mix output on XLR
30Hz at 24dB/oct
EQ (MUSIC-FLAT-VOCAL) - Volume - Ground Switch
220 Volt / 110 Volt 50/60Hz
Textured black paint-black perforated Steel-12xM8 Flying points
867 x 497 x 600 mm (34.13" x 19.57" x 23.62")
97.44 lbs / 44.2 kg
14.674 CFT
Soft-Start, compressor, High Frequency Electronic Dynamic Protection
412
For Passive Speaker Cabinets
Please use only the power connectors to make connections with other signal source
equipment for the passive speaker cabinets. The power connector has four terminals: 1+,
2-, 2+, 2-.
For TPS BETA 1152 / 2152, with the “MODE SWITCH” on BI-AMP position, 1+ / 1- used to
connect with the Low Frequency, 2+ / 2- used to connect with High Frequency.
For Active Speaker Cabinets
As to these circumstances, audio connections is mostly intended for the signal flow, so,
determine the wire configuration according to your real application system and its
connecting facility. Normally, you have the following choices:
For TPS BETA 1152 / 2152, with the “MODE SWITCH” on Full Range position & TPS BETA
SUB Series, 1+ / 1- used to connect the Speaker + / Speaker -, 2+ / 2- not used.
6
TOPP PRO
MUSIC GEAR
Wire Connections
513
TOPP PRO
MUSIC GEAR
7
TECHNICAL SPECIFICATIONS
Model
System type
Crossover Modes
Crossover Frequency
Power Rated
Nominal Impedance
Sensitivity (1W,1m)
Maximum SPL 1mt
Frequency Response
Low-Frequency Device
High-Frequency Device
HornCoverage (Hº x Vº)
High Frequency Protection
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
TPS BETA 1152
2-Way Vented Box
Bi-amp / Full-range, externally switchable
1.8 kHz
LF/Full-range: 8 ohms / HF: 8 ohms
Passive: 99dB / LF: 99.5dB / HF: 108dB
125dB (Calculated)
38Hz ~ 18KHz (-6dB)
15” 402mm - 3" Voice Coil
2" Compression Driver - 3” Voice Coil
90º x 60º
Electronic Dynamic Protection (both two modes)
2 x SPK4 (Pin1+; Pin1-; Pin2+; Pin2-)
Textured black paint-black perforated Steel-12xM8 Flying points
867 x 497 x 600mm (34.13" x 19.57" x 23.62")
79.81 lbs / 36.2 kg
14.67 CFT
LF/Full-range: 400W Continuous 800W Peak
HF: 100W Continuous 200W Peak / LF/Full-range: 8 ohms
Ø
Model
System Type
Amplifier Continuous Power
Amplifier Program Power
Sensitivity at 1mt
Max SPL at 1mt
Frequency Response
Input Sensitivity
Input Impedance
Horn Coverage (Hº x Vº)
Connectors
Subsonic Filter
Protections
External Control
Power Supply
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
TPS BETA 1152A
2-Way Bi-amp Active Vented Box
LOW: 500 W / HIGH: 150W
LOW: 1000 W / HIGH: 300W
997 dB
126 dB
38Hz - 18kHz (-6db)
Line 0dB
30K ohms Balanced - 15K ohms Unbalanced
90º x 60º
Combo input XLR / Link / Line - Mix output on XLR
30Hz at 24dB/oct
EQ (MUSIC-FLAT-VOCAL) - Volume - Ground Switch
220 Volt / 110 Volt 50/60Hz
Textured black paint-black perforated Steel-12xM8 Flying points
867 x 497 x 600 mm (34.13" x 19.57" x 23.62")
97.44 lbs / 44.2 kg
14.674 CFT
Soft-Start, compressor, High Frequency Electronic Dynamic Protection
14
7
TOPP PRO
MUSIC GEAR
TECHNICAL SPECIFICATIONS
Model
System type
Crossover Modes
Crossover Frequency
Power Rated
Nominal Impedance
Sensitivity (1W,1m)
Maximum SPL 1mt
Frequency Response
Low-Frequency Device
High-Frequency Device
HornCoverage (Hº x Vº)
High Frequency Protection
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
TPS BETA 2152
Quasi 3-Way Passive Vented Box
Bi-amp / Full-range, externally switchable
1.9 kHz
HF: 8 ohms
Passive: 101dB / LF: 101dB / HF: 108dB
130dB (Calculated)
38Hz ~ 18KHz (-6dB)
2 x 15” 402mm - 3" Voice Coil
2" Exit Compression Driver - 3” Voice Coil
90º x 60º
Electronic Dynamic Protection (both two modes)
2 x SPK4 (Pin1+; Pin1-; Pin2+; Pin2-)
Textured black paint-black perforated Steel-12xM8 Flying points
1313 x 497 x 600mm 51.69" x 19.57" x 23.62")
124.56 lbs / 56.5 kg
21.62 CFT
LF/Full-range: 800W Continuous 1600W Peak
HF: 100W Continuous 200W Peak / LF/Passive: 4 ohms
Ø
Model
System Type
Amplifier Continuous Power
Amplifier Program Power
Sensitivity at 1mt
Max SPL at 1mt
Frequency Response
Input Sensitivity
Input Impedance
Connectors
Subsonic Filter
Protections
External Control
Power Supply
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
Horn Coverage (Hº x Vº)
TPS BETA 2152A
Quasi 3-Way Bi-amp Active Vented Box
LOW: 650 W / HIGH: 150W
LOW: 1300 W / HIGH: 300W
101 dB
129 dB
38Hz - 18kHz (-6db)
Line 0dB
30K ohms Balanced - 15K ohms Unbalanced
Combo input XLR / Link / Line - Mix output on XLR
30Hz at 24dB/oct
EQ (MUSIC-FLAT-VOCAL) - Volume - Ground Switch
220 Volt / 110 Volt 50/60Hz
Textured black paint-black perforated Steel-12xM8 Flying points
1313 x 497 x 600 mm (51.69" x 19.57" x 23.62")
148.15 lbs / 67.2 kg
21.62 CFT
90º x 60º
Soft-Start, compressor, High Frequency Electronic Dynamic Protection
15
7
TOPP PRO
MUSIC GEAR
TECHNICAL SPECIFICATIONS
Model
System type
Continuous Power
Program Power
Impedance
Low Frequency
Sensitivity (1W,1m)
Frequency Response
Crossover Type
Max SPL
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
TPS BETA 15 SUBented Box
Passive Bandpass Enclosure
400W
15” 402mm Premium Sub woofer - 3" Voice Coil
98dB SPL 3dB
45Hz - 200Hz (-6dB)
Acoustic Filter
124dB at 1 m
740 x 750 x 590mm
92.15 lbs / 41.8 kg
11.56 CFT
800W
8 ohms
2 x SPK4 Style
Textured Black Plywood Cabinet - Black Metal Grille Protection
Ø
±
Model
System Type
Power Handling
Low Frequency
Sensitivity (1W.1m)
Frequency Response
Electronic Crossover
Control
Line Input
Line Output
Indicator
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
TPS BETA 15A SUB
Active Bandpass Enclosure
500W RMS
98dB SPL
15” 402mm Premium Sub woofer
3dB
45Hz - 200Hz (-6dB)
Volume Master Control
Combo Connector -4dBV
Connector -35dBV
124dB at 1 m
Power Indicator - Signal - Compressor
Textured Black Plywood Cabinet - Black Metal Grille Protection
740 x 750 x 590mm
108.24 lbs / 49.1 kg
11.56 CFT
Ø
±
±2
XLR ±2
14
7
TOPP PRO
MUSIC GEAR
TECHNICAL SPECIFICATIONS
Model
System type
Crossover Modes
Crossover Frequency
Power Rated
Nominal Impedance
Sensitivity (1W,1m)
Maximum SPL 1mt
Frequency Response
Low-Frequency Device
High-Frequency Device
HornCoverage (Hº x Vº)
High Frequency Protection
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
TPS BETA 2152
Quasi 3-Way Passive Vented Box
Bi-amp / Full-range, externally switchable
1.9 kHz
HF: 8 ohms
Passive: 101dB / LF: 101dB / HF: 108dB
130dB (Calculated)
38Hz ~ 18KHz (-6dB)
2 x 15” 402mm - 3" Voice Coil
2" Exit Compression Driver - 3” Voice Coil
90º x 60º
Electronic Dynamic Protection (both two modes)
2 x SPK4 (Pin1+; Pin1-; Pin2+; Pin2-)
Textured black paint-black perforated Steel-12xM8 Flying points
1313 x 497 x 600mm 51.69" x 19.57" x 23.62")
124.56 lbs / 56.5 kg
21.62 CFT
LF/Full-range: 800W Continuous 1600W Peak
HF: 100W Continuous 200W Peak / LF/Passive: 4 ohms
Ø
Model
System Type
Amplifier Continuous Power
Amplifier Program Power
Sensitivity at 1mt
Max SPL at 1mt
Frequency Response
Input Sensitivity
Input Impedance
Connectors
Subsonic Filter
Protections
External Control
Power Supply
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
Horn Coverage (Hº x Vº)
TPS BETA 2152A
Quasi 3-Way Bi-amp Active Vented Box
LOW: 650 W / HIGH: 150W
LOW: 1300 W / HIGH: 300W
101 dB
129 dB
38Hz - 18kHz (-6db)
Line 0dB
30K ohms Balanced - 15K ohms Unbalanced
Combo input XLR / Link / Line - Mix output on XLR
30Hz at 24dB/oct
EQ (MUSIC-FLAT-VOCAL) - Volume - Ground Switch
220 Volt / 110 Volt 50/60Hz
Textured black paint-black perforated Steel-12xM8 Flying points
1313 x 497 x 600 mm (51.69" x 19.57" x 23.62")
148.15 lbs / 67.2 kg
21.62 CFT
90º x 60º
Soft-Start, compressor, High Frequency Electronic Dynamic Protection
15
7
TOPP PRO
MUSIC GEAR
TECHNICAL SPECIFICATIONS
Model
System type
Continuous Power
Program Power
Impedance
Low Frequency
Sensitivity (1W,1m)
Frequency Response
Crossover Type
Max SPL
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
TPS BETA 15 SUBented Box
Passive Bandpass Enclosure
400W
15” 402mm Premium Sub woofer - 3" Voice Coil
98dB SPL 3dB
45Hz - 200Hz (-6dB)
Acoustic Filter
124dB at 1 m
740 x 750 x 590mm
92.15 lbs / 41.8 kg
11.56 CFT
800W
8 ohms
2 x SPK4 Style
Textured Black Plywood Cabinet - Black Metal Grille Protection
Ø
±
Model
System Type
Power Handling
Low Frequency
Sensitivity (1W.1m)
Frequency Response
Electronic Crossover
Control
Line Input
Line Output
Indicator
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
TPS BETA 15A SUB
Active Bandpass Enclosure
500W RMS
98dB SPL
15” 402mm Premium Sub woofer
3dB
45Hz - 200Hz (-6dB)
Volume Master Control
Combo Connector -4dBV
Connector -35dBV
124dB at 1 m
Power Indicator - Signal - Compressor
Textured Black Plywood Cabinet - Black Metal Grille Protection
740 x 750 x 590mm
108.24 lbs / 49.1 kg
11.56 CFT
Ø
±
±2
XLR ±2
16 TOPP PRO
MUSIC GEAR
7TECHNICAL SPECIFICATIONS
Model
System type
Continuous Power
Program Power
Impedance
Low Frequency
Sensitivity (1W,1m)
Frequency Response
Max SPL
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
Crossover Type
TPS BETA 18 SUBented Box
Passive Bandpass Enclosure
500W
18” 457mm Premium Sub woofer
98dB SPL 3dB
40Hz - 2160Hz (-6dB)
126dB at 1 m
850 x 850 x 700mm
115 lbs / 52.6 kg
17.86 CFT
1000W
8 ohms
Acoustic Filter
2 x SPK4 Style
Textured Black Plywood Cabinet - Black Metal Grille Protection
Ø
±
Model
System Type
Power Handling
Low Frequency
Sensitivity (1W.1m)
Frequency Response
Electronic Crossover
Control
Line Input
Line Output
Max SPL
Indicator
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
TPS BETA 18A SUB
Active Bandpass Enclosure
500W RMS
98dB SPL
18” 457mm Premium Sub woofer
3dB
99Hz - 120Hz (-6dB)
85Hz at 24dB/oct
Volume Master Control
Combo Connector 0dB / 0.775V
Connector 0dB / 0.775V
126dB at 1 m
Power Indicator - Signal - Compressor
Textured Black Plywood Cabinet - Black Metal Grille Protection
850 x 850 x 700mm
133 lbs / 60.35 kg
17.86 CFT
Ø
±
XLR
17
7
TOPP PRO
MUSIC GEAR
TECHNICAL SPECIFICATIONS
Model
System type
Continuous Power
Program Power
Speaker Sensitivity (1W.1m)
Impedance
Low Frequency
Connectors
Enclosure
Dimension (H x W x D)
Volume
Frequency Response
Crossover Type
TPS BETA 218 SUBented Box
Passive Bandpass Enclosure
1000W
5Hz - 160Hz (-6dB)
Acoustic Filter
4 Ohms
2 x 18”
650 x 1155 x 800mm
29.1 CFT
2000W
102dB SPL 3dB Max SPL: 135dB at 1 m
5
458mm - 3” Voice Coil 8 Ohms
2 x SPK4 Style
Textured Black Plywood Cabinet - Black Metal Grille Protection
±
Ø
16 TOPP PRO
MUSIC GEAR
7TECHNICAL SPECIFICATIONS
Model
System type
Continuous Power
Program Power
Impedance
Low Frequency
Sensitivity (1W,1m)
Frequency Response
Max SPL
Connectors
Enclosure
Dimension (H x W x D)
Net Weight
Volume
Crossover Type
TPS BETA 18 SUBented Box
Passive Bandpass Enclosure
500W
18” 457mm Premium Sub woofer
98dB SPL 3dB
40Hz - 2160Hz (-6dB)
126dB at 1 m
850 x 850 x 700mm
115 lbs / 52.6 kg
17.86 CFT
1000W
8 ohms
Acoustic Filter
2 x SPK4 Style
Textured Black Plywood Cabinet - Black Metal Grille Protection
Ø
±
Model
System Type
Power Handling
Low Frequency
Sensitivity (1W.1m)
Frequency Response
Electronic Crossover
Control
Line Input
Line Output
Max SPL
Indicator
Enclosure
Dimension (H x W x D)
Net weight (lbs/kg)
Volume
TPS BETA 18A SUB
Active Bandpass Enclosure
500W RMS
98dB SPL
18” 457mm Premium Sub woofer
3dB
99Hz - 120Hz (-6dB)
85Hz at 24dB/oct
Volume Master Control
Combo Connector 0dB / 0.775V
Connector 0dB / 0.775V
126dB at 1 m
Power Indicator - Signal - Compressor
Textured Black Plywood Cabinet - Black Metal Grille Protection
850 x 850 x 700mm
133 lbs / 60.35 kg
17.86 CFT
Ø
±
XLR
17
7
TOPP PRO
MUSIC GEAR
TECHNICAL SPECIFICATIONS
Model
System type
Continuous Power
Program Power
Speaker Sensitivity (1W.1m)
Impedance
Low Frequency
Connectors
Enclosure
Dimension (H x W x D)
Volume
Frequency Response
Crossover Type
TPS BETA 218 SUBented Box
Passive Bandpass Enclosure
1000W
5Hz - 160Hz (-6dB)
Acoustic Filter
4 Ohms
2 x 18”
650 x 1155 x 800mm
29.1 CFT
2000W
102dB SPL 3dB Max SPL: 135dB at 1 m
5
458mm - 3” Voice Coil 8 Ohms
2 x SPK4 Style
Textured Black Plywood Cabinet - Black Metal Grille Protection
±
Ø
18 TOPP PRO
MUSIC GEAR
8BLOCK DIAGRAM
19
8
TOPP PRO
MUSIC GEAR
BLOCK DIAGRAM
18 TOPP PRO
MUSIC GEAR
8BLOCK DIAGRAM
19
8
TOPP PRO
MUSIC GEAR
BLOCK DIAGRAM
21
10
TOPP PRO
MUSIC GEAR
GUARANTEE
Topp Pro guarantees the normal operation of the product against any defect of manufacture and /
or vice of material, by the term of (12) months, counted as of the date of purchase on the part of the
user, committing itself to repair or to change, to its election, without position some, any piece or
component that will fail in normal conditions of use within the mentioned period.
This guarantee is valid if the original buyer will have to present/display this certificate properly
sealed and signed by the selling house, accompanied by the corresponding invoice of purchase
where it consisted the model and serial number of the acquired equipment.
The guarantee does not cover:
The repairs could only be carried out the authorized technical service by Topp Pro, that will inform
about the term and other details into the repairs to take place according to this guarantee.
Topp Pro, will repair this unit in counted a term nongreater to 30 days as of the date of entrance of
the unit to the Technical Service. In those cases in that due to the particularitity of the spare part,
outside necessary their import, the repair time and the viability of the same one will be subject to
the effective norms for the import of parts, in which case one will inquire to the user about the term
and possibility into repair.
With the object of its correct operation, and of the validity of this one guarantee, this product will
have to be installed and to be used according to the instructions that are detailed in the manual
associate or the package of the product.
This unit will be able to appear for its repair, next to the invoice of purchase (or any other proof
where the date of purchase consists), to its authorized distributer Topp Pro or an authorized
technical center on watch by Topp Pro.
Exclusion of damages:
THE RESPONSABILITY OF TOPP PRO BY ANY DEFECTIVE PRODUCT IS LIMITED THE REPAIR OR
THE REPLACEMENT OF HE HIMSELF, TO TOPP OPTION PRO. IF WE CHOSE TO REPLACE THE
PRODUCT, THE REPLACEMENT CAN BE A RECONDITIONATED UNIT. TOPP PRO WILL NOT BE
RESPONSIBLE BY THE DAMAGES BASED ON THE LOST, INCONVENIENCE, LOSS OF USE,
BENEFITS, LOST SAVINGS, BY THE DAMAGE TO OTHER EQUIPMENT OR OTHER ARTICLES IN THE
USE SITE, OR BY ANY OTHER DAMAGE IF HE IS FORTUITOUS, CONSEQUENT OR OF ANOTHER
TYPE, ALTHOUGH TOPP PRO HAS BEEN NOTICED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow to the exclusion or the limitation to the fortuitous or consequent
damages, so the aforesaid limitation can not be applied to you.
This guarantee gives specific legal rights him, you you can also have other right that varies of state
to state.
- Damages caused by the illegal use of the product, repair and/or nonauthorized modification
conducted by people by Topp Pro.
- Damages caused by the connection of the equipment to other equipment different from the
specified ones in the manual of use, or by bad connection to these last ones.
- Damages caused by electrical storms, blows and/or incorrect transport.
- Damages caused by excesses or falls of tension in the network or by connection to networks
with a tension different from the required one by the unit.
- Damages caused by the presence of sand, acid of batteries, water, or any strange element inside
the equipment.
- Deteriorations produced by the course of the time, use and/or normal wear of the unit.
- Alteration or absence of the serial number of factory of the equipment.
20 TOPP PRO
MUSIC GEAR
9NOTES
This manual suits for next models
8
Table of contents
Other Topp Music Gear Enclosure manuals
