Topp Music Gear Forza 15P User manual

PROFESSIONAL SPEAKER SYSTEM
FORZA 15P

3
1. Introduction
2. Installation Tips
3. Usefull Data
4. Hookup Diagrams
5. Rigging
6. Connecting Plate
7. Frequency Response Diagram
8. Wire Connections
9. Technical Specifications
10. Guarantee
11. Notes
4
4
4
5
6
7
8
9
10
11
12

Introduction
Thank you for choosing TOPP PRO. The new TOPP PRO MUSIC GEAR cabinets have been
designed to provide a cost effective high grade solution while maintainig high quality cabinet
construction and optimum components.
The FORZA 15P, can be used for all types of applications including, but not limited to, churches,
conference centers and discos.
The woofer and driver combination provides excellent performance rivaling those cabinets
costing much more.
Speakers should be placed in a position that allows for unobstructed sound projection. In many
instances it is beneficial for speakers to elevate on tripod stands to achieve maximum dispersion
and reach. Consider TOPP PRO speaker stand or equivalent to raise speakers.
Using quality cables ensure best possible sound. Consider using TOPP PRO 16 or 14 gauge
cables or equivalent.
For best results match the speakers to a good amplifier that matches the wattage and
impedance of your speakers. Proper amplification power results in good quality audio and
longer component life. Check out.
Avoid pointing microphone directly at an amplified speaker otherwise could cause feedback
possible damaging speaker components and your hearing.
Our Professional Audio Products are designed and tested by a highly qualified engineering team
with more than 20 years of experience. Great care is placed in delivering products with excellent
performance, specifications and dependable reliability. Also great emphasis is placed in creating
and bringing to market products that can fill multiple applications and also offer customers
exceptional value.
Installation Tips
Usefull Data
Please write your serial number here for future reference.
4

Make all initial connections with all the equipments powered off, and ensure that all the
main volume controls are turned completely down.
For Passive Full-range Speaker Cabinet
1). Connect one side of the speaker cable to the Output CHA /CHB to Binding post of your stereo
power amplifier and the other side to the Input socket of your speaker cabinet.
2). Complete other connections as illustrated.
3). Turn on your mixer first, then the stereo power amplifier.
4). Turn up the volume control of your amplifier to about 70%.
5). Use PFL function to get the proper input level for the mixer, and adjust the main mix level
control to manipulate the output level.
6). After using, turn off your stereo power amplifier first, then the mixer.
4
Hookup Diagrams
5
FORZA 15PFORZA 15P
SPEAKER CABLE SPEAKER CABLE
Tripod
Mount
LINE IN LEFT/MONO
MAIN OUT LEFT MAIN OUT RIGHT
LINE IN RIGHT
AMPLIFIER
Tripod
Mount

The FORZA series speaker cabinet also provides the suspension points for installation.
(M10 x 1.5PH LENGTH: 30mm).
For further details, please refer to the right illustration.
Rigging
5
6
Suspension Point
Eye bolt
45o

Connecting Plate 6
7
(1) (2)

7
8
Frequency Response Diagram
FORZA 15P

The speaker connections are made via the rear panel 1/4" and/or Speakon® connectors for easy
interface with industry standard cables. Standard, unshielded speaker wire (avail-able at your local
pro audio or music store), with either 1/4" phone or Speakon connectors and wire gauge of 12-14
AWG is recommended.
If your amplifier uses binding posts you can use speaker cables with banana connectors, but be
sure to pay attention to the +/- polarity when making the connections. Make sure that the +
terminal of the speaker, or banana connector, is connected to the + terminal of the power amplifier,
and that the terminal of the speaker, or banana connector, is connected to the - terminal of the
power amplifier. It is important that your PA system is connected in phase, otherwise you will not
have the proper low-end response and stereo image.
Use the following diagrams below to ensure proper connections when wiring your system:
8
9
Signal Signal Tip(signal)
Ground Ground Sleeve(ground)

10
9
800 Watts
1600 Watts
129dB Max
55~20kHz (-6dB)
2.6kHz
PTC Protection for HF
8 Ohms
15" Woofer, 3" voice coil
1" driver, 1.35" voice coil
2*1/4"Jack+SPK4(Pin1+, Pin1-)
Plastic cabinet, Trapezoidal & Monitor shape,Metal grille,
Rubber foot, 3* Handles ( both side and Top)
36MM standard pole-mount / M10*4PCS Flying Points
632*386*366 mm
18.3kg/40.3(Ibs)
Model Passive
Program Power
2-Way Vented Passive Speaker Cabinet
System Type
Peak Power
Max SPL(1M/1W)
Frequency Response
Crossover
Protection
Nominal Impedance
Woofer
Driver
Connector
Enclosure Construction
Mounting
Dimensions (HxWxD)
Net Weight
FORZA 15P

10
Guarantee
11

FORZA 15P

FORZA 15P FORZA 15P

45o

(1) (2)

FORZA 15P