Topway Purewave Hydro User manual

PADO-H20 USER MANUAL
CONTROL BUTTONS:
 Percussion
 Vibration
 Speed increase (+)
 Speed decrease (-)
LED COLOR:
BATTERY INDICAT R
LED color – White for 4 sections
M DE INDICAT R
LED color – White for Percussion mode
LED color – White for Vibration mode
SPEED INDICAT R
LED color – White for all 7 sections
CHARGING CRADLE
LED color – White
Product name: Purewave Hydro

CONTROLLING THE UNIT
Current State /
Desired state
Action Next State Notes
Power is off
How to turn On unit?
1 second press of either the
Percussion or Vibration
mode button
Unit powers on and goes to
lowest speed setting on either
Vibration or Percussion mode.
Animation
–
At power N, speed
indicator bar should animate by
illuminating the 1
st
section
followed by the 2
nd
, 3
rd
, 4
th
, 5
th
, 6
th
& 7
th
. After all sections remain lit
for 1 second, only the 1
st
section
should remain lit.
Power is on
How to turn Off unit?
1 second press of selected
mode button
Unit powers off
Power is on
How to switch
m des?
1 second press of
unselected mode button
Motor
Turns FF
Unit changes to the selected
mode at Speed 1
Animation
–
At power N, speed
indicator bar should animate by
illuminating segment 1 followed
by the 2
nd
, 3
rd
, 4
th
, 5
th
, 6
th
& 7
th
.
After all segments remain lit for 1
second, only the 1
st
segment
should remain lit.
Power is on to unit
How to INCREASE
speed?
Momentary press of speed
increase button
Speed increases to next higher
speed. If speed is maximum,
then no action taken
Power is on to unit
How to DECREASE
speed
?
Momentary press
of speed
decrease button
Speed decreases to next lower
speed. If speed is minimum,
then no action taken.

BATTERY STATUS
Massager CHARGING Status
D ck CHARGING Status
Current State Action Next State Notes
At Power N Pressing either the
Vibration or
Percussion Mode
Animation – Battery status indicator lights up LED
segments representing battery charge% (25 / 50 / 75 /
100)
Battery status LEDs remain on for 5 seconds after
power on then turns off.
Unit is already N
Battery status LEDs remain on for 5 seconds after any
button is pressed, then turns off
Battery low (<10%)
Animation
–
If battery is <10%, 1
st
LED section of the
battery status indicator will blink to let user know unit is
low on battery & needs to be charged.
Unit is N and
battery is at 6V
Motor will turn off.
After 5 seconds, unit
will completely shut
down.
Animation
–
1
st
LED segment of the battery status
indicator will blink for about 5 sec nds to let user
know battery is too low and needs to be charged.
Unit is FF and
battery is at 6V
Press and hold
either Mode button
to turn on unit.
Motor does not turn
on.
Animation
–
1
st
LED segment of the battery status
indicator will blink for about 5 sec nds to let user
know battery is too low and needs to be charged.
Current State /
Desired state
Action Next State Notes
Power
on the
Massager is OFF
Dock unit on
charger while unit is
FF
-
Charger begins to
charge unit.
Animation
–
LED Segment 1 shall flash while battery is
25% or less, Segment 1 shall be solid and Segment 2
shall flash when battery voltage is greater than 25%
but less than 50%. Segment 1 & 2 shall be solid and
Segment 3 flashing while the battery voltage is less
than 75% and greater than 50%. Segment 1, 2 and 3
shall be solid and Segment 4 will flash when the
battery voltage is greater than 75% but less than
100%. All Segment shall be solid when the battery is
8.4V
Fully Charged
Check LED indicator
on charger Animation – Segment 1-4 solid
Power is
OFF
Massager is
charging
Press
Vibration or
Percussion Mode
No action
Current State /
Desired state
Action Next State Notes
Docking the
massager
Dock unit on
charger while
massager is FF
-
Charger begins to
charge unit.
Animation
–
LED on charger should
flash
Massager Docked
and fully charged
Massager is docked
and FF
If unit is fully charged,
LED indicator on
charger should
remain solid
Animation
–
LED should remain solid

FAULTS STATUS ON UNIT
FCC regulatory conformance ：
This device complies with Part 15 of the FCC Rules. Operation is sub ect to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.
RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20
cm between the radiator and your body. This transmitter must not be co-located or operating
in con unction with any other antenna or transmitter.
IC regulatory conformance
This device complies with CAN ICES-003 (B)/NMB-003(B) and CAN RSS-216 / CNR-216.
Current State Action Next State Notes
verheated while
unit is N
Motor Turns FF
LEDS animate to let user know a
fault has occurred.
Animation
–
ALL LEDs flash at 1Hz
rep rate for 5 seconds and turn
FF
verheated & unit is
FF
Motor Does N T turn on
when pressing Percussion or
Vibration Mode
LEDS animate to let user know a
fault has occurred.
Animation – ALL LEDs flash at 1Hz
rep rate for 5 seconds and turn
FF
No Fault
Massager operates normally

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada's licence-exempt RSS(s). Operation is sub ect to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
Cet appareil est conforme à la norme CAN ICES-003 (B)/NMB-003 (B) et CAN RSS-216 / CNR-216.
Cet appareil contient des émetteurs / récepteurs exempt (s) de licence qui sont conformes
aux RSS exemptes de licence d'Innovation, Sciences et Développement économique
Canada. Son fonctionnement est soumis aux deux conditions suivantes:
(1) Cet appareil ne doit pas provoquer d'interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de
provoquer un fonctionnement indésirable de l'appareil.
RF Exposure
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20
cm between the radiator and your body. This transmitter must not be co-located or operating
in con unction with any other antenna or transmitter.
Cet équipement est conforme aux limites d’ exposition aux rayonnements de la IC établies pour
unenvironnement non contrôé. Cet équipement doit être installé et fonctionner à au moins 20cm de
distance d ’ un radiateur ou de votre corps.