Torc Blinc Mini Generation II User manual

AVRCP
(Audio Video Remote Control Profile) Stereo music player remote control

Figure 2 Figure 3
Charging Port
Rubber Charging Port Cover
Charging Plug
Connect the charger to the headset.The charging time is approximately 4 hours.
During charging, the indicator shows a steady red light or with flashing.When the
battery is fully charged, the indicator red light will switches off.
When you using the headset, if you hear a cadent tone, and the indicator red
light flashes rhythmically, this indicates that the battery needs recharging.
To charge, please pull up gently on the Rubber Charging Port Cover, and turn
the Rubber Cover about 180 degrees. Expose the Charging Port and Plug the
Charger Plug into the Bluetooth headset’s Charging Port. At this time near the
Control Buttons the indicator light turns red or flashing when the battery is
charging. As Figure 2 and Figure 3 shown.
To turn the headset on
Figure 4
MFB

Example of Headsets Set-Up from Iphone4s.
①
Open the “Settings” Function
Choose “Bluetooth” Function
②
③
④
Before selecting “Choose on function”, you
need to press the Call Handling Button(MFB)
on Bluetooth® helmet until the blue and
red indicator lights start blinking.
Choose “On” function
⑤
After open the Bluetooth, it will search the
Bluetooth device automatically, and click the
Input the PIN code, the code is “0000”,
and click “Pair” command.
find device on the phone.
“Connected” will display after paired. Follow
Further Instruction per your manual of phone

Driver
Passenger
Passenger
Driver
Driver
Dr
Dr
D
D
D
D
Dr
D
Dr
Dr
Dr
Dr
Dr
D
Dr
D
D
D
D
Dr
D
Dr
D
Dr
r
Dr
D
D
Dr
Dr
D
D
r
Dr
Dr
D
D
Dr
Dr
D
Dr
D
Dr
Dr
r
r
Dr
Dr
D
Dr
D
D
r
r
r
r
D
r
r
Dr
r
r
D
D
D
D
D
D
D
D
iv
i
i
iv
iv
iv
i
iv
iv
iv
iv
iv
iv
i
i
iv
iv
v
iv
v
iv
v
v
v
v
v
v
i
i
iv
iv
v
v
i
i
v
v
iv
v
v
i
v
v
iv
v
v
v
iv
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
er
er
e
e
er
er
er
e
er
er
er
e
er
e
e
er
er
r
er
r
er
r
r
e
e
e
e
er
er
e
er
er
er
r
r
e
e
er
e
e
er
r
er
e
r
er
e
e
r
e
er
r
e
r
e
e
r
e
e
er
e
e
e
e
e
e
Dr
Dr
Dr
D
Dr
D
Dr
D
Dr
Dr
D
Dr
Dr
Dr
D
D
Dr
Dr
Dr
D
D
Dr
r
Dr
Dr
r
r
Dr
Dr
Dr
Dr
r
r
Dr
D
D
D
r
r
r
r
Dr
Dr
Dr
r
D
r
r
r
D
r
D
Dr
D
Dr
Dr
D
D
D
r
Dr
D
Dr
D
D
D
r
D
D
D
r
D
D
r
iv
i
iv
iv
iv
iv
iv
i
iv
i
i
iv
iv
iv
iv
i
iv
iv
iv
i
v
v
iv
v
iv
v
iv
iv
iv
v
iv
iv
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
i
v
i
iv
e
er
e
er
e
er
e
er
e
er
e
er
er
er
r
er
er
er
er
e
e
er
er
r
er
er
er
r
r
er
e
e
er
r
r
er
e
e
er
er
er
r
e
e
r
e
e
er
r
r
e
r
e
er
r
er
r
r
e
r
r
r
e
r
r
r
er
r
e
er
r
r
e
r

Figure 5
Last Number Redial
When the headset is idle, press and holds the Multi-Function Button
(MFB) on the helmet for approx 3 seconds, then release the MFB will
redial the last called phone number.
Mobile Phone Function

The Unit Handle
Inserted BlueTooth
Reset Button
Push Direction Clasp handle
Figure 6 Figure 7
Open Direction
Figure 8
System Reset
Push the reset button once to reset the system(Figure 7).
If you need to replace the Bluetooth® Control Unit, please follow the instructions here.
First open the Shell’s cover (Figure 6), you will see the exposed Bluetooth® Control Unit
(Figure 7). Using a small flat edge screwdriver, follow the instruction of the Figure 8, take
out the control unit (Figure 8).
Use caution when you installing the control unit, it should match up to the guide grooves
on the sides and be pushed in sufficiently.