Toro 44529 User manual

Note: When installing bearing,
apply #609 Loctite to bearing
before pressing into collar.
©The TORO Company - 1995
All Ri
g
hts Reserved
PARTS LIST
67-003
1 67-005-2612 Mounting Frame 1
2 67-004-1161 Lower Mounting Pin 1
3 01-282-0600 PTO Assembly 1
4 01-215-0050 Grease Zerk 1
5 67-005-0241 Belt Guard 1
6 67-005-2731 Pulley Shaft 1
7 67-005-2822 Bearing Mount 1
8 67-005-0131 Lower Support Arm 1
9 67-005-0121 Upper Support Arm 1
10 67-004-1371 Upper Support Arm Brace 1
11 3217-5 Hex Nut 2
12 67-004-0401 Upper Support Hinge Rod 1
13 3253-3 Lock Washer 2
14 01-264-0350 Belt 1
15 01-260-0060 Sheave 1
16 01-260-0150 Sheave 1
17 3256-2 Flat Washer 4
18 01-159-0010 Presto Pin 2
19 01-650-0110 All Thread 1
20 3217-9 Hex Nut 4
21 3253-7 Lock Washer 2
22 3256-6 Flat Washer 1
23 321-6 Capscrew - Hex Hd. 2
24 3296-39 Lock Nut 1
25 325-6 Capscrew - Hex Hd. 1
26 01-506-0040 Decal - Danger 1
27 01-260-0240 Bushing 2
28 01-163-0030 Socket Head Set Screw 1
29 322-13 Capscrew - Hex Hd. 1
30 3217-7 Hex Nut 2
31 3256-4 Flat Washer 3
32 3272-11 Cotter Pin 2
33 82-004-1171 Key 3
34 01-506-0130 Decal - Danger 1
35 323-8 Capscrew - Hex Hd. 2
36 3253-5 Lock Washer 2
37 01-506-0550 Decal - Grease 1
38 01-100-0340 Bearing (see note) 1
39 67-002-0051 Bearing Mount Assembly
(Incl. Ref. #4,6,7,38) 1
40 3217-6 Hex Nut 2
Ref.
No. Part No. Description
No.
Used
Ref.
No. Part No. Description No. Used
MODEL NO. 44529
(After Jan. 1995)
FORM NO. 01-502-1311
67 BLOWER MOUNTING KIT
for 200 SERIES GROUNDSMASTER®
PARTS LIST &
ASSEMBLY
INSTRUCTIONS

ASSEMBLY INSTRUCTIONS
67 BLOWER MOUNTING KIT
1. Mount the bearing mount assembly (A) to the
rearhousingasshowninFig.1. Fastenthebottom
bolt with a 1/2" lock washer and nut. Tighten but
leave nut loose enough to pivot. Fasten the top
bolt with a flat washer, lock washer and a nut.
Leave nut loose.
2. Attach the smaller sheave (3.65") to the pulley
shaft using a 1-1/4" bushing.
3. Attach the larger sheave (5") to the fan shaft
using a 1-1/4" bushing. Line up the fan sheave
with the pulley shaft using a straight edge.
4. Slide the belt onto the sheaves.
5. Pivot the bearing mount assembly (A) on the
bottom slot until proper tension is achieved. The
belt has a 3/16" deflectionwith 5 lbs. offorce when
properly adjusted. Tighten both 1/2" nuts on the
bearing mount.
6. Attach the 3/8" x 5" all thread to the nut on the
housing.
7.Mount thebelt guard as shown in Fig. 1. Fasten
securely.
8. Connect the PTO to the pulley shaft using a 3/8
x 2 3/4" capscrew.
12. Install the mounting frame to the lower tube on
the blower using the lower mounting pin to attach.
Secure on both ends with presto pins.
A
5" Sheave
3.65"
Sheave
Pulley Shaft
Pivot Point
Belt Guard
3/8" x 5"
all thread
3/8" x 2-3/4" Capscrew
P.T.O. Figure 1