Toro E24 Carefree User manual

Operator’s Manual
Manuel de l’Utilisateur
Manual del Operador
FORM NO. 3319–906 REV A
E24 and E36
CarefreeCordless
Walk Power Mower
Model No. 20648–8900001 & Up
Model No. 20650–8900001 & Up
Tondeuse motorisée à guidage arrière
E24 et E36
Sans Câble Carefree
Modèle No. 20648—8900001 et suivants
Modèle No. 20650—8900001 et suivants
Cortadora de césped motorizada empujada por
el usuario
E24 o E36
Sin Cable Carefree
Modelos N. 20648–8900001 y siguientes
Modelos N. 20650–8900001 y siguientes

EN–1
The Toro Company – 1997
All Rights Reserved Printed in USA
Contents
Page
Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safe Operating Practices 2. . . . . . . . . . . . . .
General Operation 2. . . . . . . . . . . . . . . . . . .
While Operating 3. . . . . . . . . . . . . . . . . . . . .
Maintenance And Storage 4. . . . . . . . . . . . .
Safety and Instruction Decals 5. . . . . . . . . .
Assembly 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Handle 6. . . . . . . . . . . . . . . . . . . . . . .
Install Side Discharge Chute 6. . . . . . . . . . .
Before Starting 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Charging Battery 6. . . . . . . . . . . . . . . . . . . .
Battery Power Status 8. . . . . . . . . . . . . . . . .
Operation 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting/Stopping Instructions 8. . . . . . . . . .
Circuit Breaker 9. . . . . . . . . . . . . . . . . . . . . .
Mowing Tips 9. . . . . . . . . . . . . . . . . . . . . . .
Adjusting Height-of-Cut 10. . . . . . . . . . . . . .
Maintenance 11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning 11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Blade 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Disposal 13. . . . . . . . . . . . . . . . . . . . .
Servicing Double-insulated Mower 13. . . . . .
Storage 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction
Thank you for purchasing a Toro product.
All of us at Toro want you to be completely satisfied
with your new product, so feel free to contact your
local Authorized Service Dealer for help with service,
genuine Toro parts, or other information you may
require.
Whenever you contact your Authorized Service
Dealer or the factory, always know the model and
serial numbers of your product. These numbers will
help the Service Dealer or Service Representative
provide exact information about your specific
product. You will find the model and serial number
decal located in a unique place on the product (Fig.1).
For your convenience, write the product model and
serial numbers in the space below.
Model No:
Serial No.
Read this manual carefully to learn how to operate
and maintain your product correctly. Reading this
manual will help you and others avoid personal injury
and damage to the product. Although Toro designs,
produces and markets safe, state-of-the-art products,
you are responsible for using the product properly
and safely. You are also responsible for training
persons who you allow to use the product about safe
operation.
The Toro warning system in this manual identifies
potential hazards and has special safety messages that
help you and others avoid personal injury, even death.
DANGER, WARNING and CAUTION are signal
words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.
DANGER signals an extreme hazard that will cause
serious injury or death if the recommended
precautions are not followed.
WARNING signals a hazard that may cause serious
injury or death if the recommended precautions are
not followed.
CAUTION signals a hazard that may cause minor or
moderate injury if the recommended precautions are
not followed.
Two other words are also used to highlight
information. “Important” calls attention to special
mechanical information and “Note” emphasizes
general information worthy of special attention.
The left and right side of the machine is determined
by standing behind the handle in the normal
operator’s position.

EN–2
Safety
IMPORTANT SAFETY
INSTRUCTIONS
This machine meets or exceeds CPSC blade safety
requirements for walk-behind rotary mowers and
the B71.1 specifications of the American National
Standards Institute, in effect at time of
production. However, improper use or
maintenance by the operator or owner can result
in injury. To reduce the potential for injury,
comply with these safety instructions and always
pay attention to the safety alert symbol which
means CAUTION, WARNING or
DANGER—“personal safety instruction.” Failure
to comply with the instruction may result in
personal injury.
WARNING: To reduce the risk of fire, electric
shock, and personal injury when using battery lawn
mowers, always follow these basic safety precautions.
READ ALL INSTRUCTIONS
BEFORE USING THIS MOWER
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE!
Safe Operating Practices
This product is capable of amputating hands and feet
and throwing objects. Always follow all safety
instructions to avoid serious injury or death.
This mower is designed for cutting and mulching
grass. Any use for purposes other than these could
prove dangerous to user or bystanders.
General Operation
1. Read this manual carefully before operating the
mower. Become familiar with the controls and
proper use of the mower. Never allow children
under 16 years of age to operate the mower.
Never allow adults to operate mower without
proper instructions.
2. The operator of the mower is responsible for
keeping everyone, especially children and pets,
away from area of operation. The operator is
responsible for accidents or hazards occurring to
other people or their property.
3. Thoroughly inspect area where mower will be
used and remove sticks, stones, wire, and debris
that could be picked up and thrown by mower.
Watch for foreign objects while mowing.
Objects struck by the lawn mower blade can
cause severe injuries to persons.
4. Wear long pants and substantial non-skid rubber
soled shoes. Do not operate mower while
wearing open-toed shoes, jewelry, loose clothing
or when barefoot.
5. Keep all guards, shields, safety devices, side
discharge chute or optional grass catcher in
place. Repair or replace damaged parts,
including decals. Never tamper with safety
devices. Check their proper operation regularly.
6. The motor and blade are designed to stop within
3 seconds after releasing the control bail. Ensure
that the control bail functions properly before
each use of mower. If the blade does not stop
within 3 seconds when the control bail is
released, contact your local Authorized Toro
Service Dealer for proper “On/Off” adjustment
or replacement.
7. Before using, always visually inspect to see that
the blades, blade fasteners and cutter assembly
are not worn or damaged. Replace worn or
damaged blades and fasteners in sets to preserve
balance.

EN–3
8. Only use those accessories and attachments
designed to be used with this product. Use of
any accessory or attachment not designed for this
product may increase the risk of injury.
While Operating
1. Do not insert key into plug receptacle until you
are ready to mow.
2. Do not operate mower in gaseous, explosive
atmospheres. Normal sparking of motor could
ignite fumes.
3. Start the motor carefully according to
instructions and with feet well away from the
blade.
4. Use Right Appliance – Do not use lawn mower
for any job except that for which it is intended.
5. Stay Alert – Watch what you are doing. Do not
operate mower when tired or under the influence
of drugs, alcohol or medication.
6. Be alert and turn mower off if children enter the
area.
7. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
8. Do not mow near drop-offs, ditches, or
embankments. The operator could lose footing
or balance.
9. Avoid dangerous environments. Never operate
mower in wet grass or damp locations. Do not
use mower in the rain.
10. Always maintain secure footing. Keep a firm
grip on the handle and walk; never run. Mow
only in daylight or in good artificial light.
11. Mow across the face of slopes; never up and
down. Use extreme caution when changing
direction on slopes. Do not mow excessively
steep slopes. Wear skid resistant shoes on slopes.
12. Don’t Overreach – Keep proper footing and
balance at all times.
13. Do not force the mower. It operates best and
safest at the rate for which it was designed.
14. Always wear safety glasses or eye shields during
operation to protect eyes from foreign objects
that may be thrown from the machine. (Regular
eyeglasses are not safety glasses.)
15. Always wear an approved dust mask when using
unit in dusty conditions.
16. Keep face, hands, and feet away from the mower
housing and cutter blade when the motor is
running. Blade can cause injury to hands and
feet. Stay behind the handle until the motor
stops.
17. Use extreme caution when reversing or pulling
the mower toward you. Before and while moving
backwards, look behind and down for small
children.
18. Since the blade rotates for a few seconds after
the control bar is released, stay behind the
handle until all moving parts stop.
19. After striking a foreign object or if mower
vibrates abnormally, stop motor and remove key
from plug. Check mower for damage and make
all repairs before using mower again. If major
repairs are ever needed or if assistance is desired,
contact your local Authorized TORO Service
Dealer.
20. Do not operate mower if it has been dropped or
damaged in any way. Repair any damage before
operating mower.
21. Stop the motor, wait for all moving parts to stop,
and remove the key from plug before adjusting
the height-of-cut.
22. Stop the motor when pushing the mower outside
the lawn area.
23. Stop the motor and remove the key from plug
before removing side discharge chute or optional
grass catcher.

EN–4
24. Stop motor before leaving the operator’s
position—behind the handle. Remove key from
plug receptacle if mower will be unattended.
25. If mower must be lifted to be transported, stop
motor, stay behind the handle until all moving
parts stop and remove the key from the plug
receptacle.
Maintenance And Storage
1. Perform only those maintenance instructions
described in this manual. If major repairs are
ever needed or if assistance is desired, contact
your local Authorized TORO Service Dealer.
2. Before mower is cleaned, inspected, serviced, or
adjusted, stop motor and wait for all moving
parts to stop. Remove key from plug.
3. Do not charge lawn mower in rain or in wet
locations.
4. To prevent electric shock while charging, repair
or replace any damaged electrical cords
immediately.
Note: The extension cord is only needed to
recharge the battery. It is not used for
mowing with the mower.
5. Don’t abuse extension cord while charging. Do
not yank cord to remove it from plug receptacle.
Keep cord away from heat, oil and sharp edges.
6. When replacing batteries, all batteries should be
replaced at the same time. Mixing fresh and
discharged batteries could increase internal cell
pressure and rupture the battery(ies).
7. When inserting the batteries into this product,
the proper polarity or direction must be
observed. Reverse insertion of batteries can
result in burned wires, sparks, leakage or
explosion of batteries.
8. Remove key before servicing, cleaning, or
removing material from the lawn mower.
9. Use only the following type and size
battery(ies): YUASA Maintenance-free
Rechargeable Battery YLM18-12 12V 17.2 Ah.
10. Do not dispose of the battery(ies) in a fire; the
cell may explode. Check with local codes for
special disposal instructions.
11. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
12. Exercise care in handling batteries in order not to
short the battery (contact both positive and
negative battery posts) with conducting materials
such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
13. To ensure the mower is in safe operating
condition, frequently check and keep all nuts,
bolts, and screws tight. Ensure blade bolt is
tightened to 35-40 ft–lb (48-54 Nm
14. Always keep a sharp blade on your mower.
When servicing blade, refer to blade
maintenance section for correct installation and
servicing procedures. Use identical replacement
blades only.
15. To reduce fire hazard, keep motor free of
excessive grass, leaves, and accumulations of
dirt.
16. Check optional grass catcher bag frequently for
wear or deterioration. Replace with a new bag
when worn or damaged for your protection.
17. When not in use, remove key and store mower
indoors in a dry, locked-up place out of the reach
of children. Allow motor to cool before storing
in an enclosure.
18. At the time of manufacture, the mower
conformed to the safety standards in effect for
rotary mowers. To assure best performance and
continued safety certification of the mower, use
genuine TORO replacement parts and
accessories. Replacement parts and accessories

EN–5
made by other manufacturers may result in
non–conformance with the safety standards, and
that could be dangerous.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE!
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near
any area of potential danger. Replace any decal that is damaged or lost.
ON KEY
ON CONTROL PANEL
ON REAR OF MOWER
ON MULCH PLUG
ON MULCH PLUG

EN–6
Assembly
IMPORTANT: Do not insert the key into the
plug receptacle until mower is fully
assembled.
Install Handle
IMPORTANT: Control cable must be over,
not under, handles (Fig. 2).
POTENTIAL HAZARD
•Excessive pulling on control cable may
cause mower to start. When mower is
operating, blade is rotating.
WHAT CAN HAPPEN
•Contact with rotating mower blade could
cause serious personal injury.
HOW TO AVOID THE HAZARD
•Do not lift mower by control cable or pull
excessively on cable.
1. Lift control cable above holes in rear of shroud.
2. Lower Handle – Slide ends of lower handle into
holes in shroud.
If handle stops before screw holes are aligned in
center of shroud openings, push down on lower
handle section while pushing tubes into holes in
shroud (Fig. 3). Push tubes in until screw holes
are centered in shroud openings.
Secure ends of lower handle with two screws.
3. Upper Handle (Fig. 4) – Handle height is
adjustable to three different heights for operator
comfort. Stand behind mower to gauge height.
Position ends of upper handle on outside of
lower handle. Select one set of upper handle
holes and align with lower handle holes. Secure
handles in place with bolts and knobs.
4. If handles are in highest height position, use clip
to attach cable to left side of lower handle tube
(Fig. 5).
If handles are in lowest height position, use clip
to attach cable to right side of lower handle tube
(Fig. 6).
Install Side Discharge Chute
1. Use handle on mulch door to raise door (Fig. 7).
2. Hook side discharge chute onto pegs (Fig. 8).
3. Lower mulch door on top of side discharge chute
(Fig. 10).
Before Starting
Charging Battery
It takes approximately 12–16 hours to charge a fully
discharged battery. Charge the battery after every
use. If the battery is not recharged after every use,
the battery life will be shortened. Recharge even if
mower is only run for a few minutes. This battery
does not have a “memory.”
Note: The battery is charged at the factory.
However, before using mower the first
time, it is necessary to recharge battery
and ensure it has a full charge before
operating.
To charge battery:
1. Always charge mower in a dry area protected
from the weather. Also, keep mower away from
water and any flammable substances.
2. If key is in plug receptacle, remove it (Fig. 11).
3. Insert extension cord into the plug receptacle and
connect other end of extension cord to a normal
120 volt household outlet (Fig. 13). Refer to
Securing Extension Cord, page 7.
4. The three vertical LED lights on the control
panel will indicate the charging status (Fig. 14).
Refer to the Charging Chart, page 7, for a
summary of the LED lights.

EN–7
The red light on the control panel will begin to
flash to indicate battery is present and is ready to
charge.
5. After a few minutes, the red light will stop
flashing and become a steady red. This indicates
the battery is charging.
6. When the battery is almost fully charged, the red
light will go out and the green light will go on.
The red and green light will alternately turn on
and off. When the green light is on more than the
red light, the battery is fully charged.
IMPORTANT: Your mower has been
designed to be safe if left continually on
charge for extended periods of time. It is
recommended that the battery be left
continually on charge when it is not in use
during the mowing season. During the
non-mowing season, the mower can be
unplugged and stored if the battery is fully
charged.
Note: When the mower is left on charge, it is
normal for the red and green lights to
alternately turn on and off.
LED CHARGING LIGHTS CHART
Charging Status Red Green Yellow
Pre-charge qualification – charger testing battery
condition/trickle charging battery. Trickle charge can
last from minutes to hours.
blinking off off
Battery charging on off off
Battery charged off on off
Battery absent or defective off off on
Charging fault – charger malfunctioning not applicable not applicable on
Charge pending – temperature too hot or cold to
charge not applicable not applicable blinking
Securing Extension Cord
Use only a UL listed (CSA certified in Canada)
extension cord.
POTENTIAL HAZARD
•Contact with water while operating unit
could cause electric shock.
WHAT CAN HAPPEN
•Electric shock can cause injury or death.
HOW TO AVOID THE HAZARD
•Don’t handle plug or mower with wet
hands or while standing in water.
•Use only a UL listed (CSA certified in
Canada) extension cord.
To reduce the risk of electric shock, this mower has a
polarized plug (one blade is wider than the other)
(Fig. 12) and will require the use of a polarized
extension cord. The polarized extension cord
receptacle will fit onto the mower plug only one way.
If the extension cord receptacle does not fit fully onto
the mower plug, reverse the cord receptacle. If the
cord receptacle still does not fit, obtain a correct
polarized extension cord. A polarized extension cord
will require the use of a polarized wall outlet. The
extension cord plug will fit into the polarized wall
outlet only one way. If the cord plug does not fit fully
into the wall outlet, reverse the cord plug. If the cord
plug still does not fit, contact a qualified electrician to
install the proper wall outlet. Do not change the
mower plug, extension cord receptacle, or extension
cord plug in any way.

EN–8
1. Insert extension cord receptacle onto mower plug
(Fig. 13).
Note: Do not unplug extension cord by
pulling on cord. To unplug, grasp the
cord ends, not the cord.
POTENTIAL HAZARD
•The electrical cord could be damaged.
WHAT CAN HAPPEN
•A damaged electrical cord could cause a
shock or fire.
HOW TO AVOID THE HAZARD
•Thoroughly inspect electrical cord before
charging unit. If cord is damaged, do not
charge unit. Replace or repair damaged
cord immediately. Contact your TORO
service dealer for assistance.
Battery Power Status
The three horizontal LED lights at the top of the
control panel indicate approximately how much
charge is left in the battery while the mower is in
operation (Fig. 14). The lights are only accurate when
the mower is operating and cutting grass. The
following is an explanation of the symbols under the
battery power status LED lights:
Full Box – Battery is between 50%–100% charged.
Half Full Box – Battery is between 5%–50%
charged.
Empty Box – Battery has less than 5% charge left and
should be recharged.
IMPORTANT: The battery’s life will be
shortened if mower is run after battery lights
have turned off. Do not continue to mow.
Recharge battery.
Operation
This mower is intended for residential use only.
POTENTIAL HAZARD
•When key is in plug receptacle, mower is
operational. Someone could accidentally
start the mower.
WHAT CAN HAPPEN
•Accidental starting of mower could
seriously injure you or other bystanders.
HOW TO AVOID THE HAZARD
•Always remove key from plug receptacle
when leaving mower unattended, even for a
short period of time.
Key
The mower will only operate when key is fully seated
in plug receptacle (Fig. 15). To prevent accidental
starting or unauthorized use of mower, always
remove key from plug receptacle when leaving
mower unattended. The key has a tab with a hole in it
to allow key to be hung from a nail, out of the reach
of children. Read warning label on key.
Starting/Stopping Instructions
To Start Motor
1. Push mower onto a flat concrete or asphalt
surface.
Note: Starting mower in thick grass could
cause mower to clog.
2. Insert key fully into plug receptacle (Fig. 15).
3. Pull control bar toward handle while pushing
down slide on control (Fig. 16).
4. Squeeze control bar to handle (Fig. 17).

EN–9
Note: Keep mower running when turning
mower. Turning mower off when
making a turn does not save battery
energy.
To Stop Motor
1. Release control bar.
2. Remove key from plug receptacle if mower will
be unattended for any period of time. Hang key
in a high place out of reach of children.
3. Always charge battery immediately after each
use of mower. If battery is not charged after
each use, battery life will be shortened. See
Charging Battery in Before Starting section.
IMPORTANT: Your mower has been
designed to be safe if left continually on
charge for extended periods of time. It is
recommended that the battery be left
continually on charge when it is not in use
during the mowing season. During the
non-mowing season, the mower can be
unplugged and stored if the battery is fully
charged.
Circuit Breaker
If mower is run under too much load, the circuit
breaker will trip. Follow these instructions to reset
circuit breaker.
IMPORTANT: Never reset circuit breaker
when key is in receptacle and control bar is
squeezed to handle.
1. Remove key from plug receptacle (Fig. 15).
2. Wait 30 seconds to 1 minute before pushing in
circuit breaker button (Fig. 15).
3. Reinstall key in plug receptacle.
4. Resume cutting under less load.
If circuit breaker repeatedly trips, raise the
height-of-cut or side discharge.
Mowing Tips
Battery Run Time
With a battery powered lawn mower, the condition of
the grass and the way that you mow the grass will
affect the how long the battery will run on a single
charge at each mowing.
The following are some things that will affect battery
run time:
•Moisture content of grass – The more moisture
there is in the grass, the faster the battery will
run down.
•Walking/mowing speed – The faster you walk,
the faster the battery will run down.
•Mode of operation – Mulching grass requires the
most battery energy. Bagging requires the second
highest amount of battery energy and side
discharging uses the least.
•Height-of-cut setting – If you are experiencing
problems with the battery running down too fast,
try raising the height-of-cut setting one notch.
General Mulching Tips
Your mower is designed to mulch grass when the
mulch door is completely closed (Fig. 7). Follow
these instructions whether cutting grass or leaves for
the best cutting results and lawn appearance:
•Maintain a sharp blade throughout the cutting
season. Periodically file down nicks on blade.
•Only mow dry grass or leaves. Wet grass and
leaves tend to clump on yard and may cause
mower to plug or motor to stall. They may also
be slippery to walk on and could cause you to
slip and fall.

EN–10
POTENTIAL HAZARD
•Wet grass or leaves can cause you to slip
and contact blade.
WHAT CAN HAPPEN
•Blade contact can seriously injure you.
HOW TO AVOID THE HAZARD
•Mow only in dry conditions.
•Remove key from receptacle and clean clippings
or leaves from underside of mower deck after
each mowing.
•Grass grows at different rates at different times
of the year. In the heat of summer, it is generally
best to cut grass at the 2!/2”, 3” or 3!/2”
height-of-cut settings. Only about !/3of the
grass blade should be cut off. Cutting below the
2!/2”setting is not recommended unless grass is
sparse or it is late fall when grass growth begins
to slow down.
•When changing height-of-cut from the
established setting (ex. 2!/2”, 3” or 3!/2”) to a
lower height, the grass may appear ragged or
uneven until the grass adjusts to the new
established height-of-cut and regains its normal
appearance.
•When cutting grass over six inches tall, you may
want to first mow using the side discharge chute
or try the highest height-of-cut setting and a
slower walking speed; then mow again at a
lower setting for best lawn appearance. If grass
is too long and leaves clumps on top of lawn,
mower may plug and cause motor to stall.
•Alternate mowing direction. This helps disperse
clippings over lawn for even fertilization.
If the finished cut lawn appearance is unsatisfactory,
try one or more of the following:
•Sharpen the blade.
•Walk at a slower pace while mowing.
•Raise the height-of-cut setting on your mower.
•Cut grass more frequently.
•Overlap cutting swaths instead of cutting a full
swath with each pass.
•Set height-of-cut on front wheels one notch
lower than rear wheels. (example: set front
wheels at 2 inch setting and rear wheels at 2.5
inch setting)
Cutting Leaves
•When cutting is complete, always be sure that
50% of the lawn shows through the cut leaf
cover. This may require one or more passes over
the leaves.
•For light leaf coverage, position all wheels at the
same height-of-cut setting.
•Walk at a slower mowing speed if leaves are not
being cut up finely enough to be hidden down in
the grass.
•If you cut up a lot of oak leaves, you might want
to add lime to your grass in the spring. Lime
reduces the acidity of oak leaves.
Adjusting Height-of-Cut
The mower has five height-of-cut adjustments: 1!/2”,
2”, 2!/2”, 3” and 3!/2”. The rear adjustment lever
adjusts the height-of-cut for both rear wheels, and the
front adjustment lever adjusts both front wheels.

EN–11
POTENTIAL HAZARD
•Adjusting height-of-cut levers could bring
hands into contact with moving blade.
WHAT CAN HAPPEN
•Contact with blade could cause serious
personal injury.
HOW TO AVOID THE HAZARD
•Stop motor, wait for all moving parts to
stop and remove key from plug receptacle
before changing the height-of-cut.
•Do not put fingers under housing to lift
mower when adjusting height-of-cut levers.
1. Stop motor and wait for all moving parts to stop.
Remove key from plug receptacle.
2. For easier adjustment, lift housing up so wheels
are off ground. Do not place hands under deck
to lift housing. Squeeze adjustment lever toward
wheel and move lever to desired setting
(Fig. 18). Ensure pin on adjustment lever
engages notch in mower housing. Adjust all
wheels to the same setting.
Note: For easier adjustment of rear wheels,
grasp lower handle with one hand and
lift up mower slightly so wheel is off
ground. Then squeeze adjustment
handle toward wheel.
Maintenance
POTENTIAL HAZARD
•When key is in plug receptacle, mower is
operational. Someone could accidentally
start the mower.
WHAT CAN HAPPEN
•Accidental starting of mower could
seriously injure you or other bystanders.
HOW TO AVOID THE HAZARD
•Always remove key from plug receptacle
when leaving mower unattended, even for a
short period of time.
Cleaning
Before cleaning mower, stop motor, wait for all
moving parts to stop, and remove key from plug
receptacle.
IMPORTANT: Do not spray or pour water on
mower when cleaning. Moisture can be
trapped in mower and may cause corrosion
of internal parts.
After Every Use
•Clean the underside of the mower housing. Be
particularly careful to keep the front cavity clear
of all debris (Fig. 19). Remove dirt and grass
clippings with a hardwood scraper. Avoid burrs
and sharp edges.
•Brush all debris off top of mower housing.
Once A Year
•Remove top shroud (Fig. 23) and clean out any
debris from underneath it and around battery
with compressed air, a vacuum cleaner or a
brush.

EN–12
IMPORTANT: Do not use metal objects to
clean around battery. If metal objects contact
the positive and negative posts at the same
time, this could short the battery. The battery
or conductor may overheat and cause burns.
•Check for any discolored or charred wires and
battery and switch contacts. If any are damaged,
see your Authorized Toro Service Dealer for
repairs.
Blade
Always mow with a sharp blade. A sharp blade cuts
cleanly and without tearing or shredding the grass
blades like a dull blade.
POTENTIAL HAZARD
•Motor could be started by someone
accidentally.
WHAT CAN HAPPEN
•Accidental starting of motor could cause
serious injury to operator or bystanders.
HOW TO AVOID THE HAZARD
•Do not attempt to inspect, remove or
replace blade without first removing the
key from the plug receptacle.
1. Stop motor and wait for all moving parts to stop.
Remove key from plug receptacle.
2. Tip mower on its side (Fig. 19).
3. EXAMINING BLADE – Carefully examine
blade for sharpness and wear, especially where
flat and curved parts meet (Fig. 20A). Since sand
and abrasive material can wear away the metal
that connects the flat and curved parts of the
blade, check blade before using the mower. If a
slot or wear is noticed (Fig. 20B & 20C), replace
blade. Refer to step 5.
Note: For best performance, install new blade
before cutting season begins. During
the year, file down small nicks to
maintain the cutting edge.
POTENTIAL HAZARD
•A worn or damaged blade could break and
a piece of blade could be thrown in
operator’s or bystander’s direction.
WHAT CAN HAPPEN
•A thrown piece of blade could cause serious
personal injury or death to operator or
bystanders.
HOW TO AVOID THE HAZARD
•Inspect blade periodically for wear or
damage.
•Replace a worn or damaged blade.
4. REMOVING BLADE–Grasp end of blade using
a rag or thickly padded glove. Remove blade
bolt, washer and blade (Fig. 21).
5. SHARPENING BLADE – Using a file, sharpen
top side of blade and maintain original cutting
angle (Fig. 22). The blade will remain balanced
if same amount of material is removed from both
cutting edges.
IMPORTANT: Check balance of blade by
putting it on a blade balancer. An inexpensive
balancer can be purchased at a hardware
store. A balanced blade stays in a horizontal
position and an unbalanced blade settles to
the heavy side. If blade is not balanced, file
more metal off cutting edge on heavy end of
blade.
6. Reinstall sharp, balanced blade, washer and
blade bolt. Sail part of blade must point toward
top of mower housing to ensure correct
installation. Washer is curved and must be
reinstalled with curve side down as shown in
Figure 21. Tighten blade bolt to 35-40 ft-lb
(48-54 Nm).

EN–13
Battery Disposal
Battery Removal
1. Remove four screws from shroud (Fig. 23).
Remove shroud.
2. Move control panel out of the way.
3. Remove screw from battery hold-down strap.
4. Disconnect positive and negative wires from
battery terminals.
5. The bottom of the battery pack is secured with
tape to mower housing. Rock battery pack to
free batteries from tape.
Disposing of Battery
DO NOT PLACE USED BATTERIES IN YOUR
REGULAR TRASH!
THIS SEALED LEAD (ACID) BATTERY MUST
BE COLLECTED, RECYCLED OR DISPOSED
OF IN AN ENVIRONMENTALLY SOUND
MANNER.
The incineration, landfilling or mixing of sealed lead
(acid) batteries with the municipal solid waste stream
is PROHIBITED BY LAW in some areas.
Return this battery to a federal or state approved
sealed lead (acid) battery recycler. This may be where
you purchased the battery.
Contact your local waste management officials for
other information regarding the environmentally
sound collection, recycling and disposal of this
battery.
Servicing Double-insulated
Mower
In a double-insulated mower, two systems of
insulation are provided instead of grounding. No
grounding means is provided on a double-insulated
mower, nor should a means for grounding be added to
the mower. Servicing a double-insulated mower
requires extreme care and knowledge of the system,
and should be done only by qualified service
personnel. Replacement parts for a double-insulated
mower must be identical to the parts they replace. A
double-insulated mower is marked with the words
“DOUBLE INSULATION” or “DOUBLE
INSULATED.” The symbol (square within a square)
may also be marked on the mower.
Storage
Store mower in a cool, clean, dry place. Do not store
mower if it contains a battery in a warm basement.
Cover mower to keep it clean and protected.
1. Clean mower housing. See Cleaning section in
Maintenance chapter.
2. Remove grass clippings, dirt and grime from
external parts of the shrouding and top of mower
housing.
3. Check condition of blade. See Blade section in
Maintenance chapter.
4. Tighten all nuts, bolts, and screws.
5. Your mower has been designed to be safe if left
continually on charge for extended periods of
time. It is recommended that the battery be left
continually on charge when it is not in use
during the mowing season. During the
non-mowing season, the mower can be
unplugged and stored if the battery is fully
charged.

TORO CAREFREEtELECTRIC MOWER
RELOCATION PROGRAM
If you move to a home with a lawn too large to be practically mowed with your
CareFree mower, you may send this certificate to Toro for a $50 off coupon on the
purchase of a new Toro gas mower. Coupon is redeemable at participating Toro
dealers.
Mail a copy of this certificate to:
Toro CareFreetMower Programs Administration
8111 Lyndale Avenue South
Bloomington, MN 55420–1196
Name
Current Street Address
City State Zip
Phone – –
CareFree Mower Model Number
Serial Number
A certificate will be sent to your new address as shown below. Please allow 4 weeks
for delivery.
New Address
City State Zip
New Phone (if available) – –
Size of new yard under 1/4 acre
1/4 acre to 1/2 acre
over 1/2 acre
The certificate is nontransferable and must be used by the original Toro CareFree
mower purchaser towards the purchase of a new Toro gas powered mower.
Signed

 ) ( %+' .  !( -&'(( ''$).
TheToroCompanypromisestorepairanyTOROProductused
for normal residential purposes* if defective in materials or
workmanship. The following time period applies from the date
of purchase:
STORO Cordless and
Electric Mowers 2 year full warranty. . . . . . . . . . . . . . . . . . .
The cost of parts and labor is included, but the customer pays
the transportation costs.
* Normal residential purposes means mowing the lawn on
the same lot as your home. Use at more than one location
is considered commercial use and the commercial use
warranty would apply.
 ) '%*)( ' %+' .  !( ''$).
This warranty applies to all TORO Cordless and Electric Mow-
ers. All otherTORO gas poweredor electric powered products
are covered by separate warranty statements.
%, %*) %##'!" (
Toro Consumer Products used for commercial, institutional or
rental use are warranted against defects in material or work-
manship. Components failing due to normal wear are not cov-
eredbythiswarranty.Thefollowingtimeperiodappliesfromthe
date of purchase:
STORO Cordless and
Electric Mowers
Used Commercially 45 day limited warranty. . . . . . . . . . . . .
%, % %* ) ''$). '+!
Should your TORO Product require warranty service, contact
the retailer who sold you the product or any Authorized TORO
Service Dealer or TORO Master Service Dealer. The Yellow
Pages of your telephone directory is a good reference source.
The dealer will either arrange service at his/her dealership or
recommend another Authorized Service Dealer who may be
more convenient. You may need proof of purchase (copy of
registration card, sales receipt, etc.) for warranty validation.
If for any reason you are dissatisfied with the Service Dealer’s
analysis of the defect in materials or workmanship or if you
need a referral to a TORO Service Dealer, please feel free to
contact us at the following address:
Toro Customer Service Department
8111 Lyndale Avenue South
Bloomington, MN 55420–1196
612–888–8801
800–348–2424
A Full Two-Year Warranty
(Limited Warranty for Commercial Use)




 . )!()!%$ *'$)
If for any reason you are not satisfied with your TORO Cordless
orElectricMowerwithin30daysofpurchaseforresidentialuse,
you may return the mower to the retail outlet where purchased.
Theretailerwillofferthepurchasertheoptionofeitherarefundof
the original purchase price or credit for the full value toward the
purchaseofanyTorogaspoweredmower.Allrefundorcreditar-
rangements must be made through the retailer who originally
sold you the TORO Cordless or Electric Mower.
 ) *() %* % % &   ''$). $ )
You must maintain your TORO Product by following the mainte-
nanceproceduresdescribedintheoperator’smanual.Suchrou-
tinemaintenance,whetherperformedbyadealerorbyyou,isat
your expense.
 ) %(  !( ''$). %) %+'
$
%, %( %*' )) , ") %  !( ''$).
Thereis no other express warranty.This express warranty does
not cover:
SCost of regular maintenance service or parts, such as filters,
lubricants, blade sharpening, and/or cable/linkage adjust-
ments.
SAny product or parts which has been altered or misused or
required replacement or repair due to accidents or lack of
proper maintenance.
SRepairs necessary due to improper battery care, electrical
supply irregularities, or failure to properly prepare the mower
prior to any period of non-use.
SPickup and delivery charges.
AllrepairscoveredbythiswarrantymustbeperformedbyanAu-
thorized TORO Service Dealer using Toro approved replace-
ment parts.
The Toro Company is not liable for indirect, incidental or
consequential damages in connection with the use of the
TORO Products covered by this warranty, including any
cost or expense of providing substitute equipment or ser-
vice during reasonable periods of malfunction or non-use
pending completion of repairs under this warranty. Some
states do not allow exclusions of incidental or consequen-
tial damages, so the above exclusion may not apply to you.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
   

Customers who have purchased TORO Products exported from the United States or Canada should contact their TORO
Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with
your Distributor’s service or have difficulty obtaining guarantee information, contact the TORO importer. If all other remedies
fail, you may contact us at The Toro Company.
       

Français
F–1
Table des matières
Page
Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sécurité 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consignes de sécurité 2. . . . . . . . . . . . . . . . .
Recommandations générales 2. . . . . . . . . . .
Utilisation 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Entretien et entreposage 4. . . . . . . . . . . . . . .
Décalcomanies de sécurité et instructions 6.
Assemblage 7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Montage du mancheron 7. . . . . . . . . . . . . . .
Montage de l’éjecteur latéral 7. . . . . . . . . . .
Avant la mise en marche 7. . . . . . . . . . . . . . . . . .
Charge de la batterie 7. . . . . . . . . . . . . . . . .
Etat de charge de la batterie 9. . . . . . . . . . . .
Fonctionnement 10. . . . . . . . . . . . . . . . . . . . . . . . .
Clé 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instructions pour la mise en marche et
l’arrêt 10. . . . . . . . . . . . . . . . . . . . . . . . . . .
Coupe–circuit 10. . . . . . . . . . . . . . . . . . . . . . .
Conseils de tonte 11. . . . . . . . . . . . . . . . . . . .
Réglage de la hauteur de coupe 12. . . . . . . . .
Entretien 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nettoyage 13. . . . . . . . . . . . . . . . . . . . . . . . . .
Lame 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mise au rebut de la batterie 14. . . . . . . . . . . .
Entretien d’une tondeuse à double isolement 15
Remisage 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Garantie Couverture arrière. . . . . . . . . . . . . . . . . . . .
Introduction
Merci pour votre achat d’un produit Toro.
Chez Toro, notre désir à tous est que vous soyez
entièrement satisfait de votre nouveau produit.
N’hésitez donc pas à contacter votre concessionnaire
agréé local qui tient à votre disposition un service
d’entretien et de réparations, des pièces détachées et
toute information qui pourrait vous être utile.
Chaque fois que vous contactez votre concessionnaire
agréé ou l’usine, tenez à sa disposition les numéros de
modèle et de série du produit. Ces numéros aideront
le concessionnaire ou le représentant du service
après-vente à vous fournir des informations précises
pour votre produit particulier. Les numéros de modèle
et de série de l’appareil sont indiqués sur une
décalcomanie comme illustré à la figure 1.
A titre de référence, notez les numéros de modèle et
de série du produit dans l’espace ci-dessous.
No. de modèle :
No. de série :
Lisez attentivement ce manuel pour vous familiariser
avec l’utilisation et l’entretien correct de votre
produit. La lecture de ce manuel vous aidera, ainsi
que les autres utilisateurs, à éviter des accidents
corporels et des dommages au produit. Bien que Toro
conçoive, fabrique et commercialise des produits
sûrs, à la pointe de la technologie, vous avez la
responsabilité de l’utiliser correctement et en toute
sécurité. Vous êtes également responsable d’instruire
les personnes auxquelles vous permettrez d’utiliser le
produit, sur l’usage en toute sécurité.
Les mises en garde de ce manuel identifient les
dangers potentiels et comprennent des messages de
sécurité spécifiques destinés à vous éviter ainsi qu’à
d’autres des blessures ou même la mort. Les mises en
garde sont intitulées DANGER, PRUDENCE et
ATTENTION, suivant le niveau de danger. Toutefois,
quel que soit ce niveau, soyez extrêmement prudent.
DANGER signale un risque extrême de blessures ou
de mort si les précautions recommandées ne sont pas
respectées.
ATTENTION signale un risque de blessures ou de
mort si les précautions recommandées ne sont pas
respectées.
PRUDENCE signale un risque de blessures légères
ou modérées si les précautions recommandées ne sont
pas respectées.

F–2
Deux autres termes sont également utilisés pour
signaler des messages d’informations essentielles :
“Important”, pour attirer l’attention sur des
informations mécaniques spécifiques, et “Remarque”,
pour des informations d’ordre général méritant une
attention particulière.
Les côtés droit et gauche de la tondeuse sont
identifiés comme tels en se tenant en position
normale de tonte, derrière le mancheron.
Sécurité
INSTRUCTIONS DE SÉCURITÉ
IMPORTANTES
Cette machine satisfait ou excède les normes
CPSC relatives à la sécurité de la lame pour les
tondeuses rotatives guidées par l’arrière, ainsi que
les spécifications B71.1 de l’American National
Standard Institute en vigueur au moment de la
production. Toutefois, un usage ou un entretien
incorrect de la part de l’utilisateur ou du
propriétaire peut résulter en un accident. Pour
réduire les risques d’accident, respecter les
présentes règles de sécurité et les mises en garde
pour la sécurité personnelle intitulées
ATTENTION, PRUDENCE OU DANGER—,
accompagnées du symbole de sécurité . Tout
manquement à se conformer à ces directives peut
résulter en un accident.
ATTENTION: Pour éviter les risques d’incendie, de
décharge électrique et de blessures lors de l’utilisation
de tondeuses à gazon sur batterie, toujours respecter
les consignes de sécurité qui suivent.
LIRE TOUTES LES
INSTRUCTIONS AVANT
D’UTILISER LA TONDEUSE
CONSERVER CES
INSTRUCTIONS POUR
RÉFÉRENCE ULTÉRIEURE!
Consignes de sécurité
Ce produit est capable d’amputer les mains et les
pieds et de projeter des objets. Toujours respecter
toutes les mesures de sécurité pour éviter des
blessures graves ou la mort.
La tondeuse est destinée à la tonte et au paillage de
l’herbe. Toute utilisation à d’autres fins peut être
dangereuses pour l’utilisateur ou les personnes à
proximité.
Recommandations générales
1. Lire attentivement ce manuel avant d’utiliser la
tondeuse. Se familiariser avec les commandes et
l’usage correct. Ne jamais laisser les enfants de
moins de 16 ans utiliser la tondeuse. Ne jamais
laisser des adultes utiliser la tondeuse sans
instructions adéquates.
2. L’opérateur de la tondeuse a la responsabilité de
veiller à tenir tout le monde, en particulier les
enfants et les animaux domestiques, à l’écart de
la zone de tonte. Il sera tenu responsable des
accidents ou de la mise en danger d’autres
personnes et de leurs biens.
3. Inspecter soigneusement la zone à tondre et la
débarrasser des branches, pierres, fils de fer et
autres débris susceptibles d’être projetés par la
tondeuse. Pendant la tonte, ouvrir l’oeil pour
voir à temps les les objets étrangers encore
cachés dans l’herbe. Des objets percutés par la
lame de la tondeuse peuvent occasionner des
blessures grave.
4. Porter des pantalons et de solides chaussures
antidérapantes à semelle de caoutchouc. Ne pas
tondre pieds nus ou en sandales. Ne pas porter de
bijoux ou de vêtements flottants.

F–3
5. Veiller à ce que les pièces de garde ou de
protection, les systèmes de sécurité, l’éjecteur
latéral ou le sac à herbe en option soient toujours
en place. Réparer ou remplacer les pièces
endommagées, y compris les autocollants.
N’apporter aucune altération aux dispositifs de
sécurité. Contrôler régulièrement le bon
fonctionnement de ces dispositifs.
6. Le moteur et la lame doivent s’arrêter dans les 3
secondes lorsqu’on lâche la barre de commande.
Avant chaque utilisation de la tondeuse, s’assurer
que la barre de commande fonctionne
correctement. Si la lame ne s’arrête pas dans les
3 secondes lorsqu’on lâche la barre de
commande, s’adresser à un réparateur Toro agréé
pour faire régler le système “marche/arrêt” ou le
remplacer.
7. Avant d’utiliser la tondeuse, toujours vérifier si
les lames, boulons de lame et ensembles de
coupe ne sont pas usés ou endommagés.
Remplacer les boulons et les lames usées ou
endommagées par paires pour ne pas modifier
l’équilibre.
8. N’utiliser que des accessoires spécifiquement
conçus pour la tondeuse. L’usage d’accessoires
non destinés à la tondeuse peut augmenter les
risques d’accidents.
Utilisation
1. Ne pas insérer la clé dans la prise tant qu’on
n’est pas prêt à tondre.
2. Ne pas faire marcher la tondeuse en présence de
gaz ou vapeurs explosifs. La production normale
d’étincelles par le moteur pourrait enflammer les
vapeurs.
3. Démarrer le moteur prudemment, conformément
aux instructions, en gardant les pieds loin de la
lame.
4. Utiliser l’appareil approprié – Ne pas utiliser la
tondeuse à des tâches pour lesquelles elle n’est
pas destinée.
5. Rester vigilant – Faire attention à ce qu’on fait.
Ne pas utiliser la tondeuse lorsqu’on est fatigué
ou sous l’influence de drogues, d’alcool ou de
médicaments.
6. Rester vigilant et couper immédiatement le
moteur de la tondeuse si des enfants pénètrent
dans la zone de travail.
7. Se montrer particulièrement prudent à l’approche
de tournants, buissons, arbres ou autres obstacles
limitant la visibilité.
8. Ne pas tondre à proximité de pentes abruptes,
fossés ou talus, en raison du risque de chute ou
de perte d’équilibre de l’utilisateur.
9. Eviter les conditions d’utilisation dangereuses.
Ne jamais utiliser la tondeuse dans de l’herbe
mouillée ou des endroits humides. Ne pas tondre
sous la pluie.
10. Toujours se tenir bien en équilibre. Tenir
fermement le mancheron et marcher, ne jamais
courir. Ne tondre que pendant la journée ou sous
un éclairage artificiel suffisant.
11. Tondre perpendiculairement à la pente, jamais
vers le haut ou le bas. Procéder avec une extrême
prudence lors d’un changement de direction sur
une pente. Ne pas utiliser la tondeuse sur des
pentes trop fortes. Sur les pentes, porter des
chaussures antidérapantes.
12. Ne pas tenter d’atteindre des endroits trop
éloignés –Toujours se tenir bien en équilibre.
13. Ne pas forcer la tondeuse. Utiliser la tondeuse à
la vitesse prévue pour obtenir les meilleurs
résultats et la plus grande sécurité.
14. Porter des lunettes de sécurité ou une protection
occulaire adéquate lors de toute utilisation de la
tondeuse, pour se protéger en cas de projection
de débris par la tondeuse. (Les lunettes
ordinaires ne sont pas des lunettes de sécurité.)
15. En conditions poussiéreuses, toujours porter un
masque anti-poussière agréé.

F–4
16. Ne pas approcher le visage, les mains ou les
pieds du carter de tondeuse et de la lame tant que
le moteur tourne. La lame peut causer des
blessures aux mains et aux pieds. Rester derrière
le mancheron jusqu’à ce que le moteur s’arrête.
17. Etre très prudent lorsqu’on travaille en marche
arrière ou qu’on tire la tondeuse vers soi. Bien
regarder en arrière et vers le bas avant de faire
marche arrière, pour s’assurer qu’il n’y a pas
d’enfants derrière soi.
18. Etant donné que la lame tourne encore pendant
quelques secondes lorsqu’on lâche la barre de
commande, rester derrière le mancheron jusqu’à
ce que toutes les pièces mobiles soient arrêtées.
19. Après avoir heurté un corps étranger ou si la
tondeuse vibre de façon anormale, arrêter le
moteur et retirer la clé de la prise. Vérifier si la
tondeuse n’est pas endommagée et effectuer
toutes les réparations nécessaires avant de
l’utiliser à nouveau. Pour toute réparation
importante ou si l’on a besoin d’aide, s’adresser
à un réparateur TORO agréé.
20. Ne pas utiliser la tondeuse si on l’a laissée
tomber ou endommagée d’une manière ou d’une
autre. Apporter les réparations nécessaires avant
de l’utiliser à nouveau.
21. Couper le moteur, attendre l’arrêt de toutes les
pièces mobiles et retirer la clé de la prise avant
de régler la hauteur de coupe.
22. Couper le moteur avant de pousser la tondeuse
en dehors de la pelouse.
23. Couper le moteur et retirer la clé de la prise
avant d’enlever l’éjecteur latéral ou le sac à
herbe en option.
24. Couper le moteur avant de quitter la position de
conduite, derrière le mancheron. Retirer la clé de
la prise avant de laisser la tondeuse sans
surveillance.
25. S’il faut soulever la tondeuse pour le transport,
couper le moteur, rester derrière le mancheron
jusqu’à l’arrêt de toutes les pièces mobiles et
retirer la clé de la prise.
Entretien et entreposage
1. N’effectuer que les opérations d’entretien
décrites dans ce manuel. Pour les réparations
importantes ou si l’on a besoin d’aide, s’adresser
à un réparateur TORO agréé.
2. Avant de nettoyer, inspecter ou régler la
tondeuse ou d’effectuer un entretien, couper le
moteur et attendre l’arrêt de toutes les pièces
mobiles. Retirer la clé de la prise.
3. Ne pas recharger la tondeuse sous la pluie ou
dans un endroit humide.
4. Pour éviter les risques d’électrocution lors de la
charge, réparer ou remplacer immédiatement le
cordon électrique s’il est endommagé.
Note: Le cordon prolongateur ne sert qu’à
recharger la batterie. Il ne s’utilise pas
pour la tonte.
5. Ne pas maltraiter le prolongateur lors de la
charge. Ne pas tirer le prolongateur par le cordon
pour le débrancher. Tenir le prolongateur à
l’écart de la chaleur, de l’huile et des arêtes
coupantes.
6. Remplacer toutes les batteries en même temps.
L’association de batteries neuves et de batteries
déchargées risque d’accroître la pression interne
des éléments et d’entraîner des ruptures de
batterie(s).
7. Les batteries doivent être mises en place sur la
tondeuse dans le bon sens, en respectant la
polarité. Un montage dans le mauvais sens peut
avoir pour conséquence des fils brûlés, des
étincelles, des fuites ou l’explosion des batteries.
8. Retirer la clé avant d’entreprendre tout entretien,
nettoyage ou démontage d’éléments de la
tondeuse.
9. Utiliser uniquement des batteries du type et de la
taille suivante: batteries YUASA rechargeables,
sans entretien, YLM18-12 12V 17.2 Ah.
10. Ne pas se débarrasser des batteries en les brûlant,
vu le risque d’explosion des éléments. Suivre les
instructions locales concernant le traitement des
déchets spéciaux.