Toro Groundsmaster 4000 Series User manual

FormNo.3422-333RevA
WingMountKit
Groundsmaster®4000SeriesRotaryMower
ModelNo.137-5580
InstallationInstructions
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
DescriptionQty.Use
Nopartsrequired–Preparethemachine.
Deckmount1
Plate1
Springpin1
Spacer2
Bolt(3/4x4-1/2inches)1
Locknut(3/4inch)1
Cabletie1
Installthekit.
Determinetheleftandrightsidesofthemachinefrom
thenormaloperatingposition.
PreparingtheMachine
1.Parkthemachineonalevelsurface.
2.Disengagethepowertakeoffandlowerthe
attachments.
3.Engagetheparkingbrake.
4.Shutofftheengineandremovethekey.
5.Waitforallmovementtostop.
6.Allowmachinecomponentstocool.
©2021—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3422-333*

InstallingtheDeckMount
1.Removethesnapringsonbothsidesofthe
U-jointasshowninFigure3.
2.Removethecapsunderthesnaprings.Thiscan
bedonebyaddingmoregreaseintotheU-joint.
3.Removetheexistinglongbolt(Figure3).
4.Removetheplateandrubbercushion(Figure
3).Discardtheplate.
5.Removetheboltsthatholdthedeckmountto
thecuttingunit(Figure3).
6.Removethebolt,locknut,andspacersthat
securethehydrauliccylindertothedeck
mount.Discardthehardwareandexistingdeck
mount(Figure3).
g367529
Figure1
1.Existingdeckmount6.Locknut(3/4inch)
2.Longbolt7.Bolt(3/4x4-1/2inches)
3.Snapring8.Bolt
4.Plate9.Lockwasher
5.Rubbercushion10.Washer
7.Usingthenewdeckmountasatemplate,locate
anddrilla9/16inchholeintotherearplateson
thecuttingunitasshowninFigure2.
g365598
Figure2
1.102mm(4inches)3.Drilla9/16inchhole
2.36mm(1-13/32inches)4.Deckmount
8.Placethenewdeckmountontothecuttingunit.
9.Installtheboltsthatsecurethedeckmountto
thecuttingunit(Figure3andFigure4);torque
to102N∙m(75ft-lb).
2

g365599
Figure3
1.Springpin7.Spacer
2.Snapring8.Bolt(3/4x4-1/2inches)
3.Rubbercushion9.Bolt
4.Plate10.Lockwasher
5.Deckmount11.Washer
6.Locknut(3/4inch)
g365601
Figure4
1.Installeddeckmount
10.InstalltheU-jointcapsandsecurethemwiththe
previouslyremovedsnaprings(Figure3).
11.Installthehydrauliccylindertothedeckmount
withabolt(3/4x4-1/2inches),locknut(3/4
inch),andspacers(Figure3);torqueto136N∙m
(100ft-lb).
12.Installthecabletie(Figure5).
g365600
Figure5
1.Cabletie
13.Startthemachineandchecktheoperationof
thecuttingunit.Ensurenohosesrubagainst
themachineandifneeded,adjustthehoses.
3