Toshiba 26DL934G User manual

26DL933G
26DL934G
OWNER’S MANUAL
DIGITAL Series

English - 1 -
English
Contents
Safety Precautions ................................................. 3
Air Circulation ..................................................... 3
Heat Damage...................................................... 3
Mains Supply ...................................................... 3
Warning ............................................................. 3
Do ....................................................................... 3
Do not ................................................................. 3
Installation and Important Information .................... 4
EXCLUSION CLAUSE........................................ 4
Important safety information .................................. 5
Removing the pedestal stand ............................. 7
The Remote Control ............................................... 8
Inserting Batteries and Effective Range of the
Remote Control................................................... 8
Connecting External Equipment............................. 9
Connecting an HDMI®or DVI Device to the HDMI
Input...................................................................... 10
To Connect an HDMI Device ............................ 10
To Connect a DVI Device.................................. 10
To Connect a Computer.....................................11
Connecting a DVD Player......................................11
Connecting to a DVD Player via YPbPr.............11
Connecting a Computer.........................................11
Connecting a USB Memory.................................. 12
Connect a USB Memory................................... 12
USB Memory Connection ................................. 12
Power Save Mode ................................................ 13
Environmental Information ............................... 13
Controlling the TV................................................. 14
Switching on ..................................................... 14
Using the Remote Control ................................ 14
Using the Controls and Connections on the TV... 14
Initial Installation .................................................. 15
Auto Tuning .......................................................... 16
Auto Tuning....................................................... 16
Manual Tuning, Analogue Fine Tuning ................. 17
Digital Aerial Manual Search............................. 17
Digital Cable Manual Search ............................ 17
Analogue Manual Search ................................. 17
Analogue Fine Tune.......................................... 17
General Operation................................................ 18
Stereo and Bilingual Transmissions.................. 18
Displaying Subtitles .......................................... 18
Viewing Main Menu .......................................... 18
Controlling Volume and Muting Sound ............. 18
Selecting Programme Positions........................ 18
Standby Notifications........................................ 18
Channel List, Sorting Programmes, Programme
Locking ................................................................. 19
Viewing Channel List ........................................ 19
Moving a Channel............................................. 19
Deleting a Channel ........................................... 19
Renaming a Channel........................................ 19
Locking a Channel............................................ 19
Viewing Info Banner, Electronic Programme
Guide.................................................................... 20
Viewing Info Banner.......................................... 20
Electronic Programme Guide............................ 20
Language Selection.............................................. 21
Language Settings............................................ 21
Preferred....................................................... 21
Current.......................................................... 21
Digital Settings - Parental Control, Menu Lock, Set
PIN........................................................................ 22
Viewing Parental Control Menu ........................ 22
Menu Lock ........................................................ 22
Child Lock......................................................... 22
Set PIN ............................................................. 22
Configuring Picture Settings................................. 23
Configuring Picture Settings ............................. 23
Picture Mode..................................................... 23
Contrast ............................................................ 23
Brightness......................................................... 23
Sharpness......................................................... 23
Colour ............................................................... 23
Power Save Mode ............................................ 23
Backlight (optional) ........................................... 23
Noise Reduction ............................................... 23
Advanced Settings........................................ 23
Reset ................................................................ 24
Changing Picture Format...................................... 25
Configuring PC Picture Settings........................... 26
PC Picture Settings (*)...................................... 26
PC Position....................................................... 26
Autoposition...................................................... 26
H Position ......................................................... 26
V Position.......................................................... 26
Dot Clock .......................................................... 26
Phase................................................................ 26
Configuring Sound Settings.................................. 27
Configuring Sound Settings.............................. 27
Operating Sound Settings Menu Items............. 27
Volume.............................................................. 27
Equalizer (Only for speaker)............................. 27
Balance (Only for speaker)............................... 27
Headphone ....................................................... 27
Sound Mode ..................................................... 27
AVL ................................................................... 27
Dynamic Bass................................................... 27
Digital Out......................................................... 27
Settings Menu Operation, Conditional Access ..... 28
Configuring Your TV’s Settings ......................... 28
Viewing Settings Menu ..................................... 28
Conditional Access ........................................... 28
Language.......................................................... 28
Parental ............................................................ 28
Timers............................................................... 28
Date/Time Settings ........................................... 28
Sources............................................................. 28
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 101_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1 08.05.2012 14:55:2408.05.2012 14:55:24

English - 2 -
English
Other Settings................................................... 28
Using a Conditional Access Module ................. 28
Setting Timers, Setting Date/Time........................ 29
Timers............................................................... 29
Setting Sleep Timer .......................................... 29
Setting Programme Timers............................... 29
Configuring Date/Time Settings........................ 29
Source Settings, Other Controls........................... 30
Configuring Source Settings............................. 30
Input Selection.................................................. 30
Configuring Other Settings - General ............... 30
Operation.......................................................... 30
Menu Timeout................................................... 30
Scan Encrypted Channels ............................... 30
Blue Background .............................................. 31
Software Upgrade............................................. 31
Application Version ........................................... 31
Hard of Hearing ................................................ 31
Audio Description.............................................. 31
Auto TV Off ....................................................... 31
Broadcast Type................................................. 31
Standby Search (*) .......................................... 31
E-Pop................................................................ 31
Teletext language.............................................. 31
USB Media Browser ............................................. 32
Manual Start ..................................................... 32
Auto Start.......................................................... 32
Playing MP3 Files............................................. 33
Viewing JPEG Files .......................................... 33
Slideshow Feature............................................ 34
Video Playback ................................................. 34
Media Browser Settings.................................... 35
To Close the Media Player................................ 35
Analogue Text Services ........................................ 36
Analogue Text Services .................................... 36
Using Text Button -TEXT .................................. 36
Acessing Sub-Pages ........................................ 36
Revealing Concealed Text ................................ 36
Holding a Page ................................................. 36
To display an initial page................................... 36
Appendix A: PC Input Typical Display Modes....... 37
Appendix B: AV and HDMI Signal Compatibility
(Input Signal Types).............................................. 38
Appendix C: Supported File Formats for USB
Mode..................................................................... 39
Appendix D: PIN Information ............................... 39
Specifications and Accessories ............................ 40
License Information .............................................. 41
Questions and Answers........................................ 42
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 201_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 2 08.05.2012 14:55:2608.05.2012 14:55:26

English - 3 -
English
Safety Precautions
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equip-
ment, care must be taken to obtain the best results and for safety to be assured. Please read the points below for your own
safety. They are of a general nature, intended to help with all electronic consumer products and some points may not apply
to the goods you have just purchased.
Air Circulation
Leave more than 10cm clearance around the television to
allow adequate ventilation. This will prevent overheating
and possible damage to the television. Dusty places should
also be avoided.
Heat Damage
Damage may occur if the television is left in direct sunlight
or near a heater. Avoid places subject to extremely high
temperatures or humidity, or locations where the temperature
is likely to fall below 5°C (41°F).
Mains Supply
The set should be operated only from a 220-240 V AC 50
Hz outlet. DO ensure that the television is not standing on
the mains lead. DO NOT cut off the mains plug from this
equipment, this incorporates a special Radio Interference
Filter, the removal of which will impair its performance. In
the UK, the fuse fitted in this plug is approved by
ASTA or BSI to BS1362. It should only be replaced by a
correctly rated and approved type and the fuse cover must be
refitted. IF IN DOUBT PLEASE CONSULT A COMPETENT
ELECTRICIAN.
Warning
To prevent the spread of fire, keep candles or other open
flames away from this product at all times.
Do
DO read the operating instructions before you attempt to
use the equipment.
DO ensure that all electrical connections (including the mains
plug, extension leads and interconnections between pieces
of equipment) are properly made and in accordance with the
manufacturers’ instructions. Switch off and withdraw the mains
plug before making or changing connections.
DO consult your dealer if you are ever in doubt about the
installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
Do not
DON’T remove any fixed cover as this may expose danger-
ous voltages.
DON’T obstruct the ventilation openings of the equipment
with items such as newspapers, tablecloths, curtains, etc.
Overheating will cause damage and shorten the life of the
equipment.
DON’T allow electrical equipment to be exposed to dripping
or splashing or objects filled with liquids, such as vases, to
be placed on the equipment.
DON’T place hot objects or naked flame sources, such as
lighted candles or nightlights on, or close to equipment. High
temperatures can melt plastic and lead to fires.
DON’T use makeshift stands and NEVER fix legs with wood
screws. To ensure complete safety, always fit the manufactur-
ers’ approved stand, bracket or legs with the fixings provided
according to the instructions.
DON’T leave equipment switched on when it is unattended,
unless it is specifically stated that it is designed for unat-
tended operation or has a standby mode. Switch off by
withdrawing the plug, make sure your family know how to do
this. Special arrangements may need to be made for people
with disabilities.
DON’T continue to operate the equipment if you are in any
doubt about it working normally, or it is damaged in any way -
switch off, withdraw the mains plug and consult your dealer.
WARNING - excessive sound pressure from earphones or
headphones can cause hearing loss.
ABOVE ALL - NEVER let anyone, especially children,
push or hit the screen, push anything into holes, slots
or any other openings in the case.
NEVER guess or take chances with electrical equipment
of any kind - it is better to be safe than sorry.
THE MAINS PLUG IS USED AS A DISCONNECTING
DEVICE AND THEREFORE SHOULD BE READILY OP-
ERABLE.
Note : Interactive video games that involve shooting
a “gun” type of joystick at the on-screen target may
not work with this TV.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 301_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 3 08.05.2012 14:55:2608.05.2012 14:55:26

English - 4 -
English
Locate the television away from direct sunlight and strong
lights. Soft, indirect lighting is recommended for comfortable
viewing. Use curtains or blinds to prevent direct sunlight
falling on the screen.
Place the TV on a stable, level surface that can support the
weight of the TV. In order to maintain stability and prevent
it falling over, secure the TV to a wall using a sturdy tie to
the clip on TV.
Install the P Clip under the stand as shown in the above illustration.
The LCD display panels are manufactured using an extreme-
ly high level of precision technology; however, sometimes
some parts of the screen may be missing picture elements
or have luminous spots. This is not a sign of a malfunction.
Please take note
The digital reception function of this television is only effective in the countries listed in the “Country” section
during the first time installation menu. Depending on country/area, some of this television’s functions may not
be available. Reception of future additional or modified services can not be guaranteed with this television.
If stationary images generated by 4:3 broadcasts, text services, channel identification logos, computer displays,
video games, on screen menus, etc. are left on the television screen for any length of time, they could become
conspicuous. It is always advisable to reduce both the brightness and contrast settings.
Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at
the 4:3 outlines. This is not a defect of the LCD TV and is not covered under the manufacturer’s warranty.
Regular use of other size modes will prevent permanent retention.
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) fire;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the
owner’s manual;
viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with
associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not
limited to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal opera-
tion or misuse of the product.
Installation and Important Information
Where to install
Make sure the television is located in a position where it cannot
be pushed or hit by objects, as pressure will break or damage
the screen. Also, please be certain that small items cannot be
inserted into slots or openings in the case.
Avoid using chemicals (such as air refreshers, cleaning
agents, etc.) on or near the TV pedestal. Studies
indicate that plastics may weaken and crack over time
from the combination effects of chemical agents and
mechanical stress (such as weight of TV). Failure to follow these
instructions could result in serious injury and/or permanent
damage to TV and TV pedestal.
Cleaning the screen and cabinet…
Turn off the power, and clean the screen and cabinet with a
soft, dry cloth. We recommend that you do not use any pro-
prietary polishes or solvents on the screen or cabinet as this
may cause damage.
* Button and stand
style is dependent on
model.
“P” Clip position on TV is dependent on model.
“P” Clip position on TV is dependent on model.
Sturdy tie
(as short
as possible)
P Clip
P Clip
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 401_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 4 08.05.2012 14:55:2608.05.2012 14:55:26

English - 5 -
English
Important safety information
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
Headphone Warning
Loud music can damage your hearing irreversibly. Do not set the volume to a high level when listening through
headphones, particularly for extended listening periods.
Information for the DVB-T function
• Any function relative to the digital television (with the DVB logo) is available only within the country or area
where such signals are transmitted. Verify with the salesperson if it is possible to receive a DVB-T signal in
the zone where you live.
• Even if the television conforms to the DVB-T specifications, the compatibility to future digital DVB-T
transmissions is not guaranteed.
• Some digital television functions may not be available in some countries.
• The DVB-T system present in this device is FTA (Free to air).
• DVB is a registered trademark of the DVB Project. This logo indicates that the product is compliant with
European Digital Broadcasting.
Possible Adverse Effects on LCD Screen
If a fixed (non-moving) pattern remains on the LCD screen for long periods of time, the image can become
permanently retained on the LCD TV panel and cause subtle but permanent ghost images. This type of
damage is NOT COVERED BY YOUR WARRANTY. Never leave your TV on for long periods of time while it
is displaying the following formats or images:
• Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.
• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on
a normal (4:3) display (Black bars at top and bottom of screen); or viewing normal style (4:3) media on a
widescreen (16:9) display (Black bars on left and right sides of screen).
IMPORTANT INFORMATION
TV Installation
If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling.
Many injuries, particularly to children, can be avoided by taking simple precautions such as:
• Only using furniture that can safely support the television.
• Ensuring the television is not overhanging the edge of the supporting furniture.
• Not placing the television on tall furniture (for example, cupboards or bookcases) without anchoring both the
furniture and the television to a suitable support.
• Not standing the television on cloth or other materials placed between the television and supporting
furniture.
• Educating children about the dangers of climbing on furniture to reach the television or its controls.
Place the TV on a stable, level surface that can support the weight of the TV. In order to maintain stability
and prevent it from falling over, secure the TV to a wall using a sturdy tie to the clip on the back of the table
top stand.
This unit has been produced according to all current safety regulations. The following safety tips should safeguard users
against careless use and the dangers related to such use.
• Although this unit has been carefully manufactured and rigorously checked prior to leaving the factory as with all electrical
appliances, it is possible for problems to develop. If you notice smoke, an excessive build-up of heat or any other unexpected
phenomena, you should disconnect the plug from the mains power socket immediately.
• Ensure that the unit is sufficiently ventilated! Never place it next to or underneath curtains!
• This set should only be connected to a 220-240V AC 50Hz mains power supply. Do not attempt to connect it to any other
type of supply.
• The socket outlet must be installed near the equipment and is easily accessible.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 501_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 5 08.05.2012 14:55:2708.05.2012 14:55:27

English - 6 -
English
• Do not open this unit. An attempt to repair the unit by a
non-expert could be dangerous and potentially cause a fire
hazard. All repairs must be carried out by qualified service
personnel only.
• Keep away from rodents. Rodents (and also cockatiels)
enjoy biting electric flexes. They can cause a short circuit
(fire hazard!) and receive a fatal electric shock.
• Always hold the plug when disconnecting the unit from
the socket outlet. Do not pull on flex. The flex can become
overloaded and cause a short circuit.
• Use a soft, dry cloth to clean the unit.
• Set up unit so that no one will trip over the flex.
• This unit is recommended to be installed on shock-free
benches in order to avoid any danger from falling.
• Take note that toddlers can pull the unit down from a table or
cupboard by means of its flex. Children can hurt themselves
when doing this.
• Do not use the unit near heat sources. The casing and flex
could be damaged by the intensity of the heat.
• The screen is made of glass and can break if damage is done
to it. Be careful when collecting sharp edged glass splitters.
• If you intend to wall mount the unit, contact the shop where
you purchased the unit for advice, and leave the installation
work to professionals. Improper installation can cause
damage and/or injuries.
• When installing the set on a wall, allow at least 10 cm
clearance between the rear of the set and the wall. Clearance
of less than 10 cm will obstruct the vents and cause
overheating to the interior of the set, resulting in faults or
damage to the set.
• Taking fall-prevention measures
- If these measures are not taken, the unit can fall and cause
damage and/or injuries.
- Contact the shop where you purchased the unit to obtain
full details of the measures.
• When a TV stand is used,
- Ensure the unit is fully on the stand and placed in the
centre.
- Do not leave the stand doors open. You could be hurt as
a result of the unit falling or breaking, or your fingers being
caught or jammed. Take extra precautions if you have
children.
• Avoid placing the unit on any surfaces that may be subject
to vibrations or shocks.
• To protect the unit during a thunder storm, unplug the AC
power cord and disconnect the aerial.
Caution: Do not touch the aerial connector.
• When you leave your home for a long period of time, unplug
the AC power cord for safety.
• The unit becomes warm when in operation. Do not place
any covers or blankets on the unit in order to prevent
overheating.
The ventilation holes should not be blocked. Do not set up
near radiators. Do not place in direct sunshine.
• When placing on a shelf, allow at least 10 cm clearance
space around the whole unit.
• The unit shall not be exposed to dripping or splashing, and
no objects filled with liquids, such as vases, shall be placed
on the apparatus.
• Liquids spilled into the unit can cause serious damage.
Switch the set off and disconnect the mains power supply,
then consult a qualified service person before attempting to
use the unit again.
• Moisture condensation occurs, for example, when you pour
a cold drink into a glass on a warm day and drops of water
form on the outside of the glass. In the same way, moisture
may condense on this unit’s internal optical pick-up lens, one
of the most crucial internal parts of the unit.
• Moisture condensation occurs in the following situations:
- When you move the unit from a cold place to a warm
place.
- When you use the unit in a room where the heater was
just turned on.
- When you use the unit in an area where cold air from an air
conditioner directly hits the unit.
- When you use the unit in a humid place.
• Never use the unit when moisture condensation may
occur.
• Using the unit when moisture condensation exists may
damage its own internal parts and discs. Connect the power
cord of the unit to the wall outlet, turn on the unit, remove the
disc, and leave it for two or three hours. After two or three
hours, the unit will warm up and moisture will be evaporated.
Leaving the TV connected to the wall outlet will help prevent
moisture condensation in the unit.
• Never place hot objects or open flame sources, such as
lighted candles or night lights, on or close to the TV. High
temperatures can melt plastic and lead to fires.
Important safety information (continued)
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 601_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 6 08.05.2012 14:55:2708.05.2012 14:55:27

English - 7 -
English
Removing the pedestal stand
When using a Wall Bracket
Please use a wall bracket appropriate for the size and weight of the LCD TV.
Two people are required for installation.•
To install a wall-mount from another manufacturer.•
(1) Unplug and remove any cables and/or other component connectors from the rear of the TV.
(2) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket.
(3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate
bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the
wall bracket.
(4) Always use the screws supplied or recommended by the wall mount manufacturer.
Note :
The bracket shown above is a sample image. The bracket and fixings are not supplied with the TV.•
A brick wall should not be used.•
Removing the pedestal stand
(1) Carefully lay the front of the unit face down on a flat, cushioned surface with the stand hanging over the
edge.
(2) Remove the screws.
(3) After the screws are removed, hold the pedestal stand in place,then remove the pedestal stand and the
plastic moulding from the TV by removing away from the TV.
NOTE: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD
panel.
For 26DL933 and 26DL934 model
Note: Follow wall bracket instructions to fit TV to bracket. It is recommended to use screws provided.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 701_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 7 08.05.2012 14:55:2708.05.2012 14:55:27

English - 8 -
English
The Remote Control
Simple at-a-glance reference of your remote control.
Inserting Batteries and Effective Range of the Remote Control
Remove the back cover to reveal the battery compartment and make sure
the batteries are inserted the right way round. Suitable battery types for this
remote are AAA, IEC R03 1.5V.
Do not combine a used, old battery with a new one or mix battery types.
Remove dead batteries immediately to prevent acid from leaking into the
battery compartment. Dispose of them in a designated disposal area.
Warning: Batteries must not be exposed to excessive heat such as sunshine,
fire or the like.
The performance of the remote control will deteriorate beyond a distance
of five metres or outside an angle of 30 degrees from the IR receiver. If the
operating range becomes reduced the batteries may need replacing.
Standby/ On mode
Subtitle on/off
Switch to TV or DVD mode
To select TV
programme number
To alter the volume
To mute the sound
To change channels
Operation LED
Programme guide
Teletext Controls
Mono-Stereo / Dual I-II
MENU On/Off
Teletext
Analogue/Digital broadcasts
Navigation Buttons
Return to previous menu
Audio description
Quick Settings
Exit menu
Freeze Picture
AV / Source
OK / Confirm
Info
Hold Page (in TXT mode)
Reveal (in TXT mode)
Note: Buttons that are not indicated
on the remote control illustration are
not functional in TV mode.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 801_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 8 08.05.2012 14:55:4008.05.2012 14:55:40

English - 9 -
English
Connecting External Equipment
Before connecting any external equipment, remove the mains plug from the wall socket.
Aerial cable:...........................................................
Connect the aerial to the ANT. socket on the rear of the TV.
SCART lead:..........................................................
If you use a decoder* or a media recorder, it is essential
that the scart cable is connected to the TV.
Before running first time installation, any connected devices
need to be set to standby mode.
The DIGITAL AUDIO socket enables the connection of a
suitable surround sound system.
HDMI®(High-Definition Multimedia Interface) is for using
with a DVD decoder or other equipment with digital audio and
video output. It is designed for best performance with 1080i
and 1080p high-definition video signals but will also accept
and display VGA, 480i, 480p, 576i, 576p and 720p signals.
PC format signals will also be displayed.
NOTE: Although this TV is able to connect to HDMI equipment,
it is possible that some equipment may not operate correctly.
A wide variety of external equipment can be connected to the
TV; therefore, the relevant owner’s manuals for all additional
equipment must be referred to for exact instructions.
If the TV automatically switches over to monitor external
equipment, return to normal TV by pressing the desired pro-
gramme position button. To recall external equipment, press
button repeatedly to switch between sources.
Regardless of source’s property, audio output from the DIGI-
TAL AUDIO socket cannot be copied.
HDMI Input
Sockets
RGB/PC
Input
SCART
Socket
Aerial/Cable
Input
TV
* a decoder
could be Digital
Satellite, Free to
Air or any other
compatible
decoder.
decoder*
COMMON INTERFACE
The Common Interface is
for a Conditional Access
Module (CAM).
USB Input
DIGITAL AUDIO
Socket
Side View
Headphone
SIDE AV Input
Menu Wheel
SIDE AV YPbPr
MODE
o
5Vdc
Max:500mA
YPbPr Input
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 901_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 9 08.05.2012 14:55:4108.05.2012 14:55:41

English - 10 -
English
Connecting an HDMI®or DVI Device to the HDMI Input
The HDMI inputs on your TV receive digital audio and
uncompressed digital video from an HDMI source device
or uncompressed digital video from a DVI (Digital Visual
Interface) source device.
These inputs are designed to accept HDCP (High-Bandwidth
Digital-Content Protection) programme material in digital form
from EIA/CEA-861-D–compliant [1] consumer electronic
devices (such as a set-top box or DVD player with HDMI
or DVI output).
NOTE:
• Some early HDMI equipment may not work properly with
your latest HDMI TV.
• Supported Audio format: Linear PCM, sampling rate
32/44.1/48kHz.
To Connect an HDMI Device
Connect an HDMI cable (type A connector) to the HDMI ter-
minal. For proper operation, it is recommended that you use
an HDMI cable with the HDMI Logo ( ).
• If your HDMI connection is capable of 1080p and/or
your TV is capable of refresh rates greater than 50Hz, you
will need a Category 2 cable. Conventional HDMI/DVI cable
may not work properly with this mode.
• HDMI cable transfers both video and audio. Separate
analogue audio cables are not required (see illustration).
• To view the HDMI device video, press button to select
HDMI1 or HDMI2.
HDMI Input
Socket
(Back)
HDMI device
To Connect a DVI Device
Connect an HDMI-to-DVI adaptor cable (HDMI type A con-
nector) to the HDMI input socket and audio cables to the RED
and WHITE SIDE AV AUDIO inputs (see illustration).
• The recommended HDMI-to-DVI adaptor cable length is
6.6 ft (2m).
An HDMI-to-DVI adaptor cable transfers video only.•
Separate analogue audio cables are required.
HDMI Input
Sockets
HDMI to DVI
Adapter Cable
(not supplied)
Audio Cable
(Not supplied)
Side Audio/Video
Connection Cable
(Supplied)
SIDE AV
SIDE AV Input
NOTE:
To ensure that the HDMI or DVI device is reset properly, it is
recommended that you follow these procedures:
• When turning on your electronic components, turn on the
TV first, and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI or DVI device first, and then the TV.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1001_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 10 08.05.2012 14:55:4508.05.2012 14:55:45

English - 11 -
English
To Connect a Computer
With either an RGB/PC or an HDMI connection, you can watch
your computer’s display on the TV and hear the sound from
the TV’s speakers.
When connecting a PC to the RGB/PC input on TV, use an
analogue RGB (15-pin) computer cable and use the SIDE
AV socket with a PC audio cable (not supplied) for audio
connection, using the supplied Side AV connection cable’s
RED and WHITE inputs (see illustration).
RGB/PC Input
(back)
SIDE AV Input
PC VGA Cable
(not supplied)
PC Audio Cable
(not supplied)
Side Audio/Video
Connection Cable
(supplied)
or
SIDE AV
To use a PC, set the monitor output resolution on the PC
before connecting it to the TV. To display the optimum picture,
use the PC setting feature.
NOTE:
Some PC models cannot be connected to this TV.•
An adaptor is not needed for computers with a
compatible mini D-sub15-pin terminal.
Depending on the DVD’s title and the specifications•
of the PC on which you are playing the DVD-Video,
some scenes may be skipped or you may not be
able to pause during multiangle scenes.
Connecting a Computer Connecting a DVD Player
Connecting to a DVD Player via YPbPr
Some DVD players are connected through
COMPONENT SOCKETS (YPbPr). In this case,
you must use the supplied Component YPbPr video
connection cable for enabling connection. First, plug
the single jack of the cable to the TV’s YPbPr socket
(side). Afterwards, insert your YPbPr cable’s (not
supplied) connectors into the plural part of the supplied
YPbPr video connection cable (see illustration below).
Colours of the connected jacks should match.
To enable audio connection, use the supplied Side AV
connection cable. First, plug single jack of the cable
to the Side AV Input of the TV. Afterwards, insert your
DVD player’s audio cable’s connectors into the plural
part of the supplied Side AV connection cable (see
illustration below). Colours of the connected jacks
should match.
YP Pr b
C nnection o
Cable
(s pplied u)
YPbPr
Veo id
Cable
(N t supp ed)
oli
DVD Player
Side AV Input Audio Cable
(Not supplied)
Side AV
Connection cable
(supplied)
Side AV
To RED & WHITE inputs
Video Connection
Audio Connection
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1101_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 11 08.05.2012 14:55:5008.05.2012 14:55:50

English - 12 -
English
Connecting a USB Memory
Connect a USB Memory
You can connect a USB memory to your TV by using•
the USB input of the TV. This feature allows you to
display/play music, photo or video files stored in a
USB memory.
It is possible that certain types of USB devices (e.g.•
MP3 Players) may not be compatible with this TV.
You may back up your files before making any•
connections to the TV set in order to avoid any
possible data loss. Note that manufacturer will not
be responsible for any file damage or data loss.
Do not pull out USB memory while playing a file.•
CAUTION: Quickly plugging and unplugging USB
devices, is a very hazardous operation. Especially,
do not repeatedly quickly plug and unplug the drive.
This may cause physical damage to the USB player
and especially the USB device itself.
USB Memory Connection
• Plug your USB memory to the USB input of the•
TV.
SIDE VIEW
USB
USB memory
NOTE: The USB socket has limited functionality, and Toshiba can
take no responsibility for damage to other connected equipment.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1201_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 12 08.05.2012 14:55:5108.05.2012 14:55:51

English - 13 -
English
Environmental Information
This television is designed to consume less energy to save environment.•
You not only help to save the environment but also can save money by reducing electricity bills, thanks to the
energy efficiency feature of this TV. To reduce energy consumption, you should take the following steps:
You can use Power Save Mode setting, located on page 23. If you set Power Save Mode as On, the TV will
switch to energy-saving mode and luminance level of TV set will be decreased to optimum level. Note that
some picture settings will be unavailable to be changed when the TV is in Power Save Mode.
When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce
energy consumption.
Disconnect power when going away for longer time.•
Note that annually, using the TV set in Power Save Mode has more power efficiency than disconnecting the TV
from the mains plug instead of keeping stand-by mode. Therefore it is highly recommended to activate Power
Save Mode setting to reduce your annual power consumption. And also it is recommended to disconnect the
TV from the mains plug to save energy more when you do not use.
Please helps us to save environment by following these steps.•
This television is designed to consume less energy.•
Harmful substances and contents that are dangerous to health, are eliminated in its design.•
This product is designed to endure longer and it is subject to recycling at the end of its service life.•
When the TV reaches the end of its service life, dispose the product in accordance with the proper recycling
process as explained on page 41.
Repair Information
Please refer all servicing to qualified personnel. Only qualified personnel must repair the TV. Please contact
your local dealer, where you have purchased this TV for further information.
Power Save Mode
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1301_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 13 08.05.2012 14:55:5108.05.2012 14:55:51

English - 14 -
English
Controlling the TV
A wide variety of external equipment can be connected via the sockets located on the side and back of the
TV. Whilst all the necessary adjustments and controls for the TV are made using the remote control, the
button on the left side of the TV may be used for some functions.
Switching on
If the standby LED is unlit, check that the mains plug is con-
nected to the power and press the middle of the button
on the left side of the TV to switch the television on. Then the
LED lights up in green. If the picture does not appear, press
button on the remote control; it may take a few moments.
To put the television into Standby, press button on the
remote control. To view the television, press button again.
The picture may take a few seconds to appear.
Note: The active Standby LED may appear for a few moments
when the TV is switched off.
For energy saving:
Turning the TV off at its mains supply, or un-plugging it, will
cut energy use to nearly zero for all TV’s. This is recom-
mended when the TV is not being used for a long time, e.g.
when on holiday.
Reducing the brightness of the screen will reduce energy use.
Energy efficiency cuts energy consumption and thus saves
money by reducing electricity bills.
NOTE: Putting the TV into standby mode, will reduce energy
consumption, but will still draw some power.
Using the Remote Control
Press the MENU button on the remote control to see the
menus.
The main menu appears as a group of icons each for a menu
option. Press the Left or Right button to select a topic.
In sub menu screen mode the menu appears as a list. Press
the Up or Down button to select a topic.
To use the options press the Up and Down buttons on the
remote control to move up and down through them and OK
button, Left or Right buttons to select the required choice.
Follow the on screen instructions. The functions of each menu
are described in detail throughout the manual.
Using the Controls and Connections on the TV
Using the menu wheel on the side of the TV:
To change volume: Press the middle button until the
volume level OSD appears. Increase the volume by
pushing the button up. Decrease the volume by pushing
the button down.
To change channel: Press the middle button until the
channel information banner appears. Scroll through the
stored channels by pushing the button up or down
To change source: Press the middle button until the
source list appears. Scroll through the available sources
by pushing the button up or down.
To turn the TV off: Press the middle of the button down
and hold it down for a few seconds, the TV will turn into
standby mode.
Please always refer to the owner’s manual of the equipment
to be connected for full details.
SIDE AV YPbPr
MODE
o
5Vdc
Max:500mA
Standby LED
Up Direction
Programme / Volume /
IR receiver
Down Direction
AV / Standby On
selection switch
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1401_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 14 08.05.2012 14:55:5108.05.2012 14:55:51

English - 15 -
English
Initial Installation
Before switching on the TV, put your decoder and media recorder to Standby if they are connected and
ensure the aerial is connected to your TV. To set up the TV, use the buttons on the remote control as
detailed on page 8.
IMPORTANT: Ensure that the aerial is connected and
a Common Interface module is not inserted before
switching on the TV for the first time installation.
Connect the mains plug and switch the TV to on1.
using the side control switch. If the TV does not
switch on, press any numbered or button on
the remote control, then the language selection
menu will be displayed. This screen will appear
the first time that the TV is switched on and each
time the TV is reset.
By pressing2. Up or Down button, highlight the
language you want to set and press OK button.
The following message will be displayed next:
By pressing3. Left or Right button, select the
country you want to set and press Down button
to highlight the Search Type option. Use Left or
Right to set the desired search type. Available
search types are digital only, analog TV only
and full.
When set,4. Down buton to select Teletext
Language. Use Left or Right button to select
desired Teletext Language.
Press5. OK button on the remote control to continue
and the following message will be displayed on
the screen:
Select6. Yes button by using Left or Right button
and press OK button to continue. Afterwards, the
following OSD will be displayed on the screen:
If you select7. Cable option, the following screen
will be displayed:
You can select frequency ranges from this8.
screen. For highlighting lines you see, use Up or
Down button. You can enter the frequency range
manually by using the numeric buttons on the
remote control. Set Start and Stop Frequency as
desired by using numeric buttons on the remote
control. After this operation, you can set Search
Step as 8000 kHz or 1000 kHz. If you select
1000 kHz, the TV will perform search process
in a detailed way. Searching duration will thus
increase accordingly. When finished, press OK
button to start automatic search.
If you select9. Aerial option from the Search Type
screen, the television will search for broadcasts.
The Auto tuning screen will appear and the10.
television will start to search for available stations.
The progress bar will move along the line. You
must allow the television to complete the search.
The following OSD will be displayed on the screen
and the television will search for the selected
broadcasts:
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1501_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 15 08.05.2012 14:55:5208.05.2012 14:55:52

English - 16 -
English
Note:You can press MENU button to cancel.
After the available stations are stored, Channel List
will be displayed on the screen. If you like the sort
channels, according to the LCN, please select Yes
and then press OK button (if available).
Press• OK button to quit channel list and watch TV.
Note:
Do not turn off the TV while initializing first time
installation.
Keep the menu of Store Mode Disabled and do not
change it, when using at home.
Auto TuningInitial Installation - continued
Auto Tuning
As new services are broadcast, it will be necessary to
retune the television in order to view them.
Auto Tuning will completely retune the television•
and can be used to update the channel list. It is
recommended that Auto Tuning is run periodically
to ensure that all new services are added. All current
channels and settings, i.e. locked channels, will
be lost.
Press• MENU button on the remote control and select
Install and Retune by using Left or Right button.
Press OK button and the following menu screen
will be displayed.
Select• Automatic Channel Scan (Retune) by using
Up or Down button and press OK button. Automatic
Channel Scan options will be displayed. You can select
options by using Up or Down and OK buttons.
Auto Channel Scan Menu Operation
Digital: Searches and stores aerial DVB stations.
Analogue: Searches and stores analogue stations.
Full: Searches and stores both analogue and aerial
DVB stationsres both analogue and cable DVB
stations.
Whenever you select an automatic search type and•
press OK button, a confirmation screen will appear
on the screen. To start installation process, select
Yes, to cancel select No by using Left or Right
and OK button.
After auto channel scan type is set and selected•
and confirmed, installation process will start and
progress bar will move along. Press MENU button
to cancel process. In such a case, located channels
are not stored. The television will start to search for
all available stations. You must allow the television
to complete the search.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1601_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 16 08.05.2012 14:55:5308.05.2012 14:55:53

English - 17 -
English
Digital Aerial Manual Search
The feature is available for service engineers or
can be used for direct channel entry if the multiplex
channel is known.
Select• Manual channel scan from the Install and
Retune menu and press OK.
After selecting search type as Digital Aerial, you
can enter the multiplex or frequency number using
the numeric buttons and press OK button to search.
Enter the multiplex number using the numeric•
buttons. The television will automatically search
for that multiplex. When the multiplex is found any
channels not currently on the programme list will be
added and the programme information at the top of
the screen will be updated.
Repeat as necessary.•
Digital Cable Manual Search
In cable manual scan, you can enter frequency,•
modulation, symbol rate and network channel scan
options. After selecting search type as Digital Cable,
you can set the desired options and press OK button
to search.
Analogue Manual Search
The television can be tuned-in manually. For example:
if the television cannot be connected to a media
recorder/decoder with a SCART lead or to tune-in a
station on another System.
To allocate a programme position on the television
for a decoder and media recorder: turn the decoder
on, insert a pre-recorded film into the media recorder
and press PLAY, then manually tune.
After selecting search type as Analogue, you can
use Up or Down button to highlight an item and then
press Left or Right button to set an option.
Enter the channel number or frequency using the
numeric buttons. You can then press OK button
to search. When the channel is located, any new
channels that are not on the list will be stored.
Analogue Fine Tune
Select• Analogue Fine Tune from the Install and
Retune menu by using Up or Down and OK
buttons. Analogue fine tune screen will be displayed.
Analogue Fine Tune feature will not be available
if there are no analogue channels, only digital
channels and external sources stored.
Use• Left or Right button to set Fine Tune. When
finished, press OK button.
Manual Tuning, Analogue Fine Tuning
The television can be tuned-in manually using Manual Search feature.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1701_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 17 08.05.2012 14:55:5308.05.2012 14:55:53

English - 18 -
English
Stereo and Bilingual Transmissions
If stereo or dual language broadcasts are transmitted, the
word Stereo or Dual will appear on the screen each time posi-
tions are changed, disappearing after a few seconds. If the
broadcast is not in stereo, the word Mono will appear.
Stereo… Press . to select Stereo or Mono.
Bilingual… Bilingual transmissions are rare. If they are
transmitted, the word Dual will be displayed. Choose the
required programme number, and if the word Dual appears,
press . to select Dual 1, Dual 2 or Mono.
For DTV broadcasts
To view current language and for changing to an
alternative language (if available), press AD.button.
Available options will be listed.
Displaying Subtitles
In digital broadcasts, this feature will show subtitles
on the screen in the selected language provided they
are being broadcast.
Press SUBTITLE button to activate available
subtitles. Press SUBTITLE button again to turn off
subtitles.
Viewing Main Menu
• Press MENU button on the remote control to view
main menu.
Controlling Volume and Muting Sound
Volume
Press or button on the remote control to
adjust the volume. Move the menu wheel on the TV
up or down to change the volume.
Sound Mute
Press “ ” button once to turn the sound off and
again to cancel.
Selecting Programme Positions
To select a programme position use the numeric
buttons on the remote control. To change the channels
using the menu wheel on the TV, first press the middle
of the menu wheel and the channel info bar appears.
Now move the menu wheel up or down to scroll
between the stored channels.
Programme positions can also be selected using P+
or P- button.
Press button to display the on-screen information
i.e. programme position, stereo/mono signal and
picture format.
Standby Notifications
If the TV switches off while in No Signal mode, the
following on-screen message will be displayed on the
next switch-on:
If the TV switches off owing to the auto power down
feature, the following on-screen message will be
displayed on the next switch-on:
General Operation
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1801_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 18 08.05.2012 14:55:5308.05.2012 14:55:53

English - 19 -
English
Viewing Channel List
The channel order may be changed to suit your personal
preference.
Select• Channel List from the main menu and press
OK button. The following menu will be displayed:
Select• Edit Channel List to manage all stored
channels. Use Up or Down and OK buttons to select
Edit Channel List.
Press• Up or Down button for selecting a channel.
You can press or button to move page up or
page down.
To watch a specific channel, highlight it by using• Up
or Down button. Afterwards press OK button.
Press• BLUE button to view filtering options.
Press• MENU button to exit.
Note: The channels listed are mixed at the channel
list. Channel types can be differentiated by the icons
next to them: DTV (digital tv), HD (HD TV) , ATV
(Analogue TV) ,TV (TV), RD (Radio), encrypted, lock,
and at the favourite list. Listed channels can also be
sorted by using the active channel list filter.
Moving a Channel
Highlight the desired channel by using• Up or Down
button.
Select Move option in the channel list and press•
OK button.
Edit Number screen will be displayed. Enter the•
desired channel number by using the numeric
buttons on the remote control. If there is a previously
stored channel on that number, a warning screen
will be displayed. Select Yes if you want to move the
channel and press OK.
Selected channel is now moved.•
Deleting a Channel
You can press GREEN button to tag/untag all
channels; YELLOW button to tag/untag channel.
Select the channel that you want to delete and select•
Delete option. Press OK button to continue.
A warning screen will appear. Select• Yes to delete,
select No to cancel. Press OK button to continue.
Renaming a Channel
Select the channel that you want to rename and•
select Edit Name option. Press OK button to
continue.
Pressing• Left or Right button moves to the previous/
next character. Pressing Up or Down button
changes the current character. Pressing the numeric
buttons ‘0...9’ replaces the highlighted character with
the characters printed above the button one by one
as the button is pressed.
When finished, press• OK button to save. Press
MENU to cancel.
Locking a Channel
You can press GREEN button to tag/untag all
channels; YELLOW button to tag/untag a single
channel.
Select the channel that you want to lock by using•
Up or Down button.
Select• Lock option by using Left or Right button.
Press OK button to continue.
You will be asked to enter parental control PIN. Enter•
the PIN number.
Note: Default PIN is set to 0000.
Press• OK button when the desired channel is
highlighted to lock/unlock the channel. Lock symbol
will be displayed next to the selected channel.
Channel List, Sorting Programmes, Programme Locking
You can view stored channels and sort them by using the Channel List feature.
01_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 1901_MB62_[GB]_(01-TV)_DVB_TC_(IB_INTERNET)_(26155LED_1911UK)_NICKEL17_10077727_10077398.indd 19 08.05.2012 14:55:5408.05.2012 14:55:54