Toshiba 28Z33B User manual

SERVICE MANUAL
Colour television
28Z33B/32Z33B
Z33 Chassis
FILE NO. 030-200314
Published in Japan Dec. 2003 (YC)

– 2 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
TABLE OF CONTENTS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS ........................................................................................................................................ 3
SET-UP ADJUSTMENT ............................................................................................................................................ 4
SERVICE MODE ...................................................................................................................................................... 8
DESIGN MODE ...................................................................................................................................................... 11
ELECTRICAL ADJUSTMENTS .............................................................................................................................. 12
CIRCUIT CHECK.................................................................................................................................................... 14
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA.............................................................................................................................. 15
LOCATION OF CONTROLS ................................................................................................................................... 16
CHASSIS AND CABINET REPLACEMENT PARTS LIST ......................................................................................18
PC BOARDS TOP & BOTTOM VIEW..................................................................................................................... 25
TERMINAL VIEW OF TRANSISTORS ................................................................................................................... 33
CIRCUIT BLOCK DIAGRAM .................................................................................................................................. 36
SPECIFICATIONS .............................................................................................................................................. END
APPENDIX:
CIRCUIT DIAGRAM

–3 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRE-
CAUTION”AND “PRODUCT SAFETY NOTICE”INSTRUCTIONS BELOW.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazard-
ous X-RAY RADIATION. To avoid such hazards, the high
voltage must not be above the specified limit. The nomi-
nal value of the high voltage of this receiver is (A) kV at
zero beam current (minimum brightness) under a (C) V
AC power source. The high voltage must not, under any
circumstances, exceed (B) kV.
Refer to table-1 for high voltage (A), (B) & AC voltage (C).
(See SETTING & ADJUSTING DATA on page 15)
Each time a receiver requires servicing, the high voltage
should be checked following the HIGH VOLTAGE CHECK
procedure in this manual. It is recommended that the
reading of the high voltage be recorded as a part of the
service record. It is important to use an accurate and
reliable high voltage meter.
2. The only source of X-RAY RADIATION in this TV
receiver is the picture tube. For continued X-RAY RA-
DIATION protection, the replacement tube must be
exactly the same type tube as specified in the parts
list.
3. Some part in this receiver have special safety-related
characteristics for X-RAY RADIATION protection. For
continued safety, parts replacement should be under-
taken only after referring to the PRODUCT SAFETY
NOTICE below.
SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver. The
following are the necessary precautions to be observed before servicing this chassis.
1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service
is performed on the receiver.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture
tube is highly evacuated and if broken, glass fragments will be violently expelled. Use shatter proof goggles and keep
picture tube away from the unprotected body while handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as;
non-metallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics
are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by
using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in this manual and its supplements; electrical components having such features are
identified by the international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute
replacement parts which do not have the same safety characteristics as specified in the parts list may create shock,
fire, X-ray radiation or other hazards.

–4 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRE-
CAUTION”AND “PRODUCT SAFETY NOTICE”ON PAGE 3 OF THIS MANUAL.
SET-UP ADJUSTMENT
■The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
Mounting position of the purity magnet assembly should fit to same position as old one because slightly difference
to the position depend on a kind of tube.
*There are no adjustment of purity and convergence in some picture tube (Unified with purity magnet)
GLASS CLOTH
TAPES
DEFLECTION
YOKE
(Put on after
adjustment)
RUBBER WEDGE
ADHESIVE
DEFLECTION
YOKE
PURITY/
CONVERGENCE
MAGNET ASS'Y
20mm(28", 32")
25mm(25")
19mm(19", 20", 21")
14mm(13", 14")
Figure 1.
COLOR PURITY ADJUSTMENT
NOTE : Before attempting any purity adjustments, the re-
ceiver should be operated for at least fifteen minutes.
1. Demagnetize the picture tube and cabinet using a de-
gaussing coil.
2. Set the brightness and contrast to maximum.
3. Use a green raster from among the built-in test signals.
4. Loosen the clamp screw holding the yoke and slide the
yoke backward or forward to provide vertical green belt
(zone) in the picture screen.
5. Remove the Rubber Wedges.
6. Rotate and spread the tabs of the purity magnet (See
figure 2.) around the neck of the picture tube until the
green belt is in the center of the screen. At the same
time, enter the raster vertically.
7. Slowly move the yoke forward or backward until a uniform
green screen is obtained. Tighten the clamp screw of
the yoke temporarily.
8. Check the purity of the red and blue raster.
TEMPORARY
MOUNTING

–5 –
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CONVERGENCE ADJUSTMENTS
NOTE: Before attempting any convergence adjustments, the
receiver should be operated for at least fifteen min-
utes.
■CENTER CONVERGENCE ADJUSTMENT
1. Use the cross-dot pattern from among the built-in test sig-
nals.
2. Set the brightness and contrast for well defined pattern.
3. Adjust two tabs of the 4-Pole Magnets to change the an-
gle between them (See figure 2.) and superimpose red
and blue vertical lines in the center area of the picture
screen.
4. Turn the both tabs at the same time keeping the angle
constant to superimpose red and blue horizontal lines at
the center of the screen.
5. Adjust two tabs of 6-Pole Magnets to superimpose red/
blue line and green one. Adjusting the angle affects the
vertical lines and rotating both magnets affects the hori-
zontal lines.
6. Repeat adjustments 3, 4, 5 keeping in mind red, green
and blue movement, because 4-Pole Magnets and 6-Pole
Magnets have mutual interaction and make dot movement
complex.
■CIRCUMFERENCE CONVERGENCE ADJUSTMENT
1. Loosen the clamping screw of deflection yoke slightly to
allow the yoke to tilt.
2. Temporarily put a wedge as shown in figure 1. (Do not
remove cover paper on adhesive part of the wedge.)
3. Tilt front of the deflection yoke up or down to obtain better
convergence in circumference. (See figure 3.) Push the
mounted wedge into the space between picture tube and
the yoke to fix the yoke temporarily.
4. Put other wedge into bottom space and remove the cover
paper to stick.
5. Tilt front of the yoke right or left to obtain better conver-
gence in circumference. (See figure 3.)
6. Keep the yoke position and put another wedge in either
upper space. Remove cover paper and stick the wedge
on picture tube to fix the yoke.
7. Detach the temporarily mounted wedge and put it in an-
other upper space. Stick it on picture tube to fix the yoke.
8. After fixing three wedges, recheck overall convergence.
Tighten the screw firmly to fix the yoke and check the yoke
is firm.
9. Stick three adhesive tapes on wedges as shown in figure
1.
Figure 2.
BLU RED
BLU
RED
RED/BLU GRN
RED/BLU
GRN
B
G
R
R
G
B
BGR
RGB
BGR
RGB
R
G
B
B
G
R
4-POLE MAGNETS MOVEMENT
INCLINE THE YOKE UP (OR DOWN)
6-POLE MAGNETS MOVEMENT
Center Convergence by Convergence Magnets
Circumference Convergence by DEF Yoke
INCLINE THE YOKE RIGHT (OR LEFT)
Figure 3. Dot Movement Pattern
4-POLE
MAGNETS
PURITY
MAGNETS
6-POLE
MAGNETS
ADJUST THE ANGLE
(VERTICAL LINES) FIXED
ROTATE TWO TABS
AT THE SAME TIME
(HORIZONTAL LINES)
CONVERGENCE MAGNET ASSEMBLY ADJUSTMENT OF MAGNETS

WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF SERVICE MANUAL.
SET-UP ADJUSTMENT (FOR FLAT TUBE)
■The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note:The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
COLOR PURITY ADUSTMENT
(1)Let the screen face in the installing direction or toward the east (when it is to be moved), bring up the service mode
screen after demagnetizing (front, left, right, and top) with the degaussing coil, receive white signals by pressing the
[TV/VIDEO] button, and then the receiver should be operated for more than 40 minutes.
(2)Perform rough adjustment of the central convergence with the P/C magnet according to the adjustment item.
(3)Receive built-in green signals, loosen set screws on the deflection yoke, remove rubber wedges, and shift the deflection
yoke to toward front.
(4)Move alternately the two 2-pole magnets of the P/C magnets so that the green raster can come to the center of the
screen.
Figu e 1.
(5)Receive built-in red and blue signals, check that there is no inclination of the single color raster toward one side, and if
each color tilts to a great extent, make adjustment with the 2-pole magnet so that the 3 colors will come to the center
evenly.
(6)Receive the green raster, shift the deflection yoke from a
foremost position (hitting against the picture tube) to a
backward position horizontally, stop the deflection yoke
at a position where it begins to become a green raster,
and perform accurate marking on the picture tube.
(7)Shift the deflection yoke further backward, and perform
accurate marking at a position where the green raster
begins to being luck.
(8)Fix the deflection yoke at a position 60% forward within
the range marked in items (6) and (7) above.
CONVERGENCE ADJUSTMENTS
* Adjust the convergence magnet to get vest convergence in the the order to (1) ~ (5).
■ CENTER CONVERGENCE:
(1)Receive the white crosshatch or dot pattern from the service signal generator.
(2)Use the 2 pieces of main 4-pole magnets of P/C magnets, change the open angle, and align the red and blue vertical
lines on the screen center.
(3)Freeze the open angle of the main 4-pole magnets, turn them simultaneously, and align the horizontal lines.
(4)Take the same steps for items (2) and (3) above and align red/blue with green on the screen center using two 6-pole
magnets.
A
P/C magnet installing position A
• 30"=26.5 mm
• 28", 32"=20 mm
• 34"=37 mm
• 34"=39 mm
Green Belt
2-pole purity magnet (28", 32")
(27": Magnet is fixed with deflection yoke.) Main 4-pole convergence magnet (28" : 32")
6-pole convergence magnet (34")
6-pole convergence magnet (30" : 32")
Main 4-pole convergence magnet (34")
Fix the deflection yoke at a position 60% forward from a
point between (6) and (7)
Picture tube
Shift deflection yoke
(6) (8) (7) Perform marking of each point
on the tape of picture tube
CRT-D board
P/C Mag
100 60 0%
GENERAL ADJUSTMENTS
–6–

(5)Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at
the initial position)
Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets.
blue
blue
red
red
Main 4-pole magnet
red/blue
red/blue
green
green
6-pole magnet
Xv bow-shaped deviation of convergence
blue
red
Sub-4-pole magnet
■ CIRCUMFERENCE CONVERGENCE:
*Perform correction in the following manner.
A
D
E
F
A
B
C
B
C
S
N
D
E
F
A
B
C
D
E
F
N
S
VR3
YV YHC
GH
GH
VR2 VR1
blue
green
red
• Adjust coils and minimize deviation
(The 27” unit has coils underneath it)
blue
green
red
(Parts code:23 948 2 4) TC-S
Blue color or blue mark
*Insert the correction piece between the
picture tube and the deflection yoke.
(Insertion position of correction
piece)
Bonded surface
blue
green
red
(Parts code:23 948 464)
Transparent
Bonded surface
Ad ust VR 1 and minimize the deviation of YH. *Only 27" and 30".
Red
green
blue
Red
green
blue
Red
green
blue
Red
green
blue
Ad ust VR 2 (YHC) and minimize the deviation of YH.
Red
green
blue
Red
green
blue
Red
green
blue
Red
green
blue
Ad ust VR 3 (YV) and minimize the deviation of YV.
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
Red
blue
green
blue
red
green
Red
blue
green
blue
red
green
■ 30", 27"
■ 28", 32"
27" (Part No. 23 947 371)
32", 30" (Part No. 23 947 121)
34" (Part No. 23 993 080)
Perform correction by inserting the
correction piece into the clear-
ance of terminal board coils of
the deflection yoke.
Note:
Perform insertion by turning the
metal side to the terminal board
side of the deflection yoke.
GENERAL ADJUSTMENTS
–7–

–8–
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SERVICE MODE
1. ENTERING TO SERVICE MODE
S
(Service mode display)
Item
Data
Mute or
3) While pressing the obutton,
press MENU button on TV set.
2) Press obutton again to
keep pressing.
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
A single horizontal line ON/OFF: INFO button (on Remote) or abutton (on TV)
Test signal selection : abutton (on Remote)
Selection of the adjustment items : Channel s/t(on TV or Remote)
Change of the data value : Volume ;+/–(on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory (QA02) : CALL + Channel button on TV (s)
Reset the count of operating protect
circuit to “00”: CALL + Channel button on TV (t)
“RCUT”selection : 1 button
“GCUT”selection : 2 button
“BCUT”selection : 3button
“SCNT”selection : 4 button
“COLC”selection : 5button
“TNTC”selection : 6 button
Self diagnostic display ON/OFF : 9 button
1) Press obutton once on
Remote Control.
Adjustment mode
Item
Data
Service mode
S
Press
Press
ITEM
DATA
Color thickness correction
CAUTION : Never try to perform initialization unless you have changed the memory IC.
note: Displayed differently as shown below, de-
pending on the setting of the receiving color
system.
COLC(PAL/NTSC)
COLS (SECAM)

–9–
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.
(tbutton for reverse order)
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 15)
5. ADJUSTING THE DATA
1) Pressing of VOLUME ;+/–button will change the value of data in the range from 00H to FFH. The variable
range depends on the adjusting item.
6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once.
■INITIALIZATION OF MEMORY DATA OF QA02
After replacing QA02, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the CALL button on the Remote, then press the CHANNEL sbutton on the TV.The initialization of QA02
has been complated.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Auto search Memory”on the owner’s manual.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described
below in SERVICE MODE.
Signals Picture
•Red raster
•Green raster
•Blue raster
•All White
•Black cross-hatch
* The signals marked with are not usable to display in the Test signal for some model.
Signal off NTSC signals (5 patterns)
PAL signals (5 patterns)

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
8. SELF DIAGNOSTIC FUNCTION
1) Press “9”button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
23******
POWER : 00
BUS LINE : OK
BUS CONT : OK
BLOCK :
UV V1 V2 V3
QV01
<SELF CHECK>
Part number of microcomputer (QA01)
Operation number of protecting circuit ----“00”is nor-
mal.
When indication is other than “00”, overcurrent apts to
flow, and circuit parts may possibly be damaged.
BUS LINE CHECK ----“OK”is normal.
“SDA1-GND”------------- SDA-GND short circuit.
“SCL1-GND”-------------- SCL-GND short circuit.
“SCL1-SDA1”------------- SCL-SDA short circuit.
BUS CONT ----“OK”is normal.
When indication shows “Q uuu NG”, the device with
the number may possibly be damaged.
BLOCK
UV : TV reception mode
V1 : VIDEO 1 input mode (a1)
V2 : VIDEO 2 input mode (a2)
V3 : VIDEO 3 input mode (a3)
Indicated color of mode now selected : Green and Red
Indicated color of other modes : White
Green : Normal
Red : The microcomputer operates to provide judgement
of no video signal. The red color is still indicated
though the signal is input, failure may exist in input
signal line including QV01.
QV01 : In case of indication green ---Normal
In case of indication red with input signal----
Failure may exist in output line including QV01.
NOTE: Component which controls character display on
screen is ICF01 (QT01) (TELETEXT IC.). If this
display function fails to operate due to damage in
ICF01 (QT01), self diagnosis procedure is as fol-
lows.
(1) In case that power indicator is blinking with
interval of 0.5 seconds; it means protecting
circuit (Current limiter) is operating, and cir-
cuit components may possibly be damaged.
Check related components.
(2) In case that power indicator is blinking with
interval of 1 second; Protecting circuit does
not operate, but a part of Bus line does not
operate normally. Check Bus line.





* The items marked with are not usable to display in the SELF DIAGNOSTIC FUNCTION for some model.
–10 –

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
DESIGN MODE
1. ENTERING TO DESIGN MODE
ITEM
DATA
S D Press
(Design mode) (Adjustment mode)
Press
3) Press MENU button on TV.
2) While pressing oor CALL button on
Remote and press MENU button on TV.
1) Select the Service mode.
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CHANNEL tbutton in the design mode changes the adjustment items in the order of table-3.
(sbutton for reverse order)
Refer to table-3 for data of design mode.
(See SETTING & ADJUSTING DATA on page 15)
3. ADJUSTING THE DATA
Pressing of VOLUME sor tbutton will change the value of data.
When QA02 is initialized, items “OPT0”, “OPT1”and “OPT2”of DESIGN MODE are set to the data of the representative
model of this chassis family.
Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to
reset the data of items “OPT0”, “OPT1”and “OPT2”.
–11 –

–12–
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
ELECTRICAL ADJUSTMENTS
1. Enter the service mode, then select any register item.
2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap-
pears on the screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture
screen.
FOCUS VR ADJ
SUB-BRIGHTNESS
(BRTC)
Note: Constrict the picture height
until the vertical retrace line
appears adjusting the item
HIT (HEIGHT).
1. Set CONTRAST to minimum, and
BRIGHTNESS to center by adjusting
user controls.
2. Set the TV in service mode to get cross-
bar of inside pattern.
3. Select BRTC (brightness correction),
and adjust the ;–/+ button to reduce
the value so that white portion of inside
pattern slightly light.
4. Adjust ;–/+ button to increase the
data value of BRTC, and set it just
before the difference between the belt of
vertical retrace and the border of black
portion of inside pattern is visible.
After that, return vertical height and
contrast.
ITEM ADJUSTMENT PROCEDURE
Belt of vertical retrace
HORIZONTAL POSITION
ADJUSTMENT (HPOS)
VERTICAL POSITION
ADJUSTMENT (VPOS)
1. Set the TV in service mode, and get
black cross-bar signal with VIDEO
button on remote hand unit.
2. Select either HPOS (Horizontal
picture phase) or VPS (Vertical
picture phase) with CHANNEL s, t
buttons, and adjust horizontal or
vertical picture position in the center
of screen with VOLUME ;–/+
buttons.
VERTICAL AMPLITUDE
ADJUSTMENT (HIT)
1. Set the TV in service mode, and get
black cross-hatch signal with VIDEO
button on remote hand unit.
2. Select HIT (Vertical amplitude) with
CHANNEL s, tbuttons, and adjust
vertical amplitude with VOLUME
;–/+ buttons so that vertical am-
plitude lacks a little.
3. Adjust vertical amplitude with VOL-
UME ;–/+ buttons so that the first
bar on cross-hatch signal touches
edge of screen.
The first

–13–
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
ITEM ADJUSTMENT PROCEDURE
WHITE BALANCE
ADJUSTMENT
•CUTOFF ADJUSTMENT
(RCUT)
(GCUT)
(BCUT)
•DRIVE ADJUSTMENT
(GDRV)
(BDRV)
1. Set Contrast to 40, and brightness to +20 by picture control.
2. Receive the Black and White pattern.
3. Select RCUT, GCUT and BCUT with CHANNEL s, tbuttons, to set individual
values to Initial reference data, and to set GDRV and BDRV to Initial reference
data with VOLUME ;–/+ buttons.
4. Press -/- - button on the remote control and rotate Screen VR to get one slight
horizontal line on screen.
Note: Every pressing of -/- - button provides Horizontal line picture and Normal
picture alternately.
5. Press -/- - button to release horizontal line picture, and select the two other colors
which did not light in the above step with CHANNEL s, tbuttons. Then tap VOL-
UME ;–/+ buttons so that three colors slightly light in the same level.
XTo correct white balance in light area,
select GDRV and BDRV with CHANNEL
s, tbuttons to adjust.
XTo correct white balance in dark area,
perform fine adjustment of RCUT, GCUT
and BCUT.
Light area check
(to show white)
Dark area check
(to show black)

–14–
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
CIRCUIT CHECK
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps
below.
1. Connect an accurate high voltage meter to the second anode of the picture tube.
2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current).
3. High voltage must be measured below (B) kV.
Refer to table-1 for high voltage (B).
(See SETTING & ADJUSTING DATA on page 15)
4. Vary the BRIGHTNESS control to both extremes to be sure the high voltage does not exceed the limit under any conditions.

–15–
GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA
CHAPTER 2 SPECIFIC INFORMATIONS
DESIGN MODE
ADJUSTING ITEMS AND DATAS IN THE DESIGN MODE:
Item Name of adjustment Preset Data Data Remarks
Table-3
SAFETY INSTRUCTIONS
Table-1
SERVICE MODE
ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:
Table-2
RCUT
GCUT
BCUT
GDRV
BDRV
BRTC
COLC
COLS
SCNT
SRY
SBY
PRY
R CUTOFF (B/W)
G CUTOFF (B/W)
B CUTOFF (B/W)
G DRIVE
B DRIVE
BRIGHT CENTRE
COLOR CEN PAL/NTSC
COLOR CEN SECAM
SUB CONTRAST
SECAM R-Y BLACK LEVEL
SECAM B-Y BLACK LEVEL
PAL R-Y BLACK LEVEL
Item Adjustment
Reference data
40H
40H
40H
40H
40H
40H
40H
40H
00H
08H
08H
08H
Item Adjustment
Reference data
VPOS
HIT
VLIN
WID
PARA
CNR
TRAP
RAGC
CSAW
CPAR
VSC
V-POSITION (ALL)
HEIGHT (WIDE)
V-LINEARITY (WIDE)
PICTURE WIDTH
E-W PARABOLA (WIDE)
E-W CORNER (WIDE)
TRAPEZIUM (WIDE)
RF AGC
CENTER SAW
CENT PARA
V-S CORRECTION
00H
35H
07H
20H
2CH
00H
30H
1EH
03H
05H
09H
* There are no adjustments of the design mode.
←
←
←
←
←
←
←
←
←
←
←
PBY PAL B-Y BLACK LEVEL 08H ←
←
21H
←
25H
22H
←
24H
←
←
04H
←
←HPOS H-POSITION (WIDE) 0DH ←
32"
HIGH VOLTAGE AT ZERO BEAM: (A) 31.7 kV
MAX HIGH VOLTAGE: (B) 35.0 kV
28"
31.4 kV
33.0 kV
AC VOLTAGE (C)
220~240 V

– 16–
LOCATION OF CONTROLS
AERIAL TERMINAL
VIDEO-1 (21PIN S-VIDEO/AV)
VIDEO-2 (21PIN S-VIDEO/AV)
Front
Rear terminals
POSITION UP
REMOTE SENSOR
VIDEO-3
POWER INDICATOR (RED)
POSITION DOWN
VOLUME UP
VOLUME DOWN
HEAD PHONE
MENU
SPECIFIC INFORMATIONS

–17–
POWER-ON/STANDBY
SELECT A PAGE
NUMBER BUTTONS
VIDEO INPUT SELECT
TELETEX CONTROL
BUTTONS
EXIT MENU
POSITION/TELETEXT
PAGE UP/DOWN
STEREO BILINGUAL
STOP
DISPLAY SIZE
MUTE
(NOT USED FOR THIS MODEL)
FAST FORWARD
DISPLAY TELETEXT
DISPLAY CALL/INDEX (TELETEXT)
HOLD A WANTED PAGE
REVEAL CONCEALED TEXT
PREVIOUS PROGRAMME
ON-SCREEN MENU
SELECT MENU
VOLUME LEVEL UP/DOWN
WIDESCREEN
STANDBY
REWIND
PLAY
PICTURE MENU
Remote Controller
SPECIFIC INFORMATIONS

WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRE-
CAUTION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components
which have special characteristics important for safety and should be replaced only with types identical to those in the
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not degrade the safety
of the receiver through improper servicing.
NOTICE:
··
··
· The part number must be used when ordering parts, in order to assist in processing, be sure to include the
Model number and Description.
··
··
· The PC board assembly with
*
mark is no longer available after the end of the production.
Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............... CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
Location Parts No. Descriptiopn
No.
Location Parts No. Descriptiopn
No.
– 18 –
Model : 28Z33B/32Z33B
CHASSIS AND CABINET REPLACEMENT PARTS LIST
#1 : [28Z33B]
#2 : [32Z33B]
CAPACITORS
C101 24797229 ELECTROLYTIC, 50V 2.2UF M
C102 24109103 CERAMIC CHIP, 50V B 0.01UF K
C103 24793221 ELECTROLYTIC, 10V 220UF M
C104 24109103 CERAMIC CHIP, 50V B 0.01UF K
C105 24797100 ELECTROLYTIC, 50V 10UF M
C106 24109102 CERAMIC CHIP, 50V B 1000PF K
C107 24109103 CERAMIC CHIP, 50V B 0.01UF K
C108 24794101 ELECTROLYTIC, 16V 100UF M
C109 24109103 CERAMIC CHIP, 50V B 0.01UF K
C110 24109103 CERAMIC CHIP, 50V B 0.01UF K
C111 24109103 CERAMIC CHIP, 50V B 0.01UF K
C112 24503049 PLASTIC FILM, 63V 0.47UF J
C113 24109103 CERAMIC CHIP, 50V B 0.01UF K
C114 24109103 CERAMIC CHIP, 50V B 0.01UF K
C115 24109103 CERAMIC CHIP, 50V B 0.01UF K
C116 24109103 CERAMIC CHIP, 50V B 0.01UF K
C118 24794101 ELECTROLYTIC, 16V 100UF M
C119 24793101 ELECTROLYTIC, 10V 100UF M
C120 24109103 CERAMIC CHIP, 50V B 0.01UF K
C121 24109103 CERAMIC CHIP, 50V B 0.01UF K
C122 24109103 CERAMIC CHIP, 50V B 0.01UF K
C123 24100102 CERAMIC CHIP, 50V F 1000PF Z
C124 24797478 ELECTROLYTIC, 50V 0.47UF M
C125 24669479 ELECTROLYTIC, 50V 4.7UF M 3A
C126 24590472 PLASTIC FILM, 50V 4700PF J
C127 24797478 ELECTROLYTIC, 50V 0.47UF M
C128 24794100 ELECTROLYTIC, 16V 10UF M
C129 24794100 ELECTROLYTIC, 16V 10UF M
C130 24109103 CERAMIC CHIP, 50V B 0.01UF K
C140 24109103 CERAMIC CHIP, 50V B 0.01UF K
C160 24567224 PLASTIC FILM, 50V 0.22UF J
C204 24797479 ELECTROLYTIC, 50V 4.7UF M
C205 24092538 CERAMIC CHIP, 10V F 1UF Z
C206 24794101 ELECTROLYTIC, 16V 100UF M
C214 24503047 PLASTIC FILM, 63V 0.33UF J
C221 24105100 CERAMIC CHIP, 50V CH 10PF D
C222 24105100 CERAMIC CHIP, 50V CH 10PF D
C223 24105100 CERAMIC CHIP, 50V CH 10PF D
C302 24214471 CERAMIC DISC, 500V B 470PF K
C303 24214471 CERAMIC DISC, 500V B 470PF K
C304 24503041 PLASTIC FILM , 63V 0.1UF J
C305 24667222 ELECTROLYTIC, 25V 2200UF M 3A
C307 24503049 PLASTIC FILM, 63V 0.47UF J
C310 24667222 ELECTROLYTIC, 25V 2200UF M 3A
C311 24669221 ELECTROLYTIC, 50V 220UF M 3A
C314 24092730 CERAMIC CHIP, 16V B 0.1UF K
C331 24590103 PLASTIC FILM, 50V 0.01UF J
C360 #1 24503041 PLASTIC FILM , 63V 0.1UF J
C366 24082049 PLASTIC FILM, 100V 47000PF J
C370 24794100 ELECTROLYTIC, 16V 10UF M
C376 24109123 CERAMIC CHIP CK73B 50V 12000PF K
C377 24590392 PLASTIC FILM CQ922M 50V 3900PF J
C410 24214471 CERAMIC DISC, 500V B 470PF K
C413 24214821 CERAMIC DISC, 500V B 820PF K
C416 24678010 ELECTROLYTIC, 200V 1UF M 3A
C417 24214391 CERAMIC DISC, 500V B 390PF K
C420 24794101 ELECTROLYTIC, 16V 100UF M
C421 24232103 CERAMIC DISC, 50V F 0.01UF Z
C423 24829433 PLASTIC FILM, 400V 0.043UF J
C430 #1 24820562 PLASTIC FILM, 630V 5600PF J
#2 24820822 PLASTIC FILM, 630V 8200PF J
C431 24232103 CERAMIC DISC, 50V F 0.01UF Z
C442 #1 24503297 PLASTIC FILM CF92 T 315V R27UF J
#2 24503295 PLASTIC FILM CF92 T 315V R22UF J
C443 #1 24503278 PLASTIC FILM CF92 T 1500VH 8700PF H
#2 24503228 PLASTIC FILM, 1500VH 6800PF H
C444 #1 24503147 PLASTIC FILM CF92 T 1500VH 8200PF H
#2 24503228 PLASTIC FILM, 1500VH 6800PF H
C445 24828473 PLASTIC FILM, 200V 0.047UF J
C446 24679330 ELECTROLYTIC, 250V 33UF M 3A
C447 #1 24829203 PLASTIC FILM, 400V 20000PF J
#2 24829273 PLASTIC FILM, 400V 0.027UF J
C448 24073118 ELECTROLYTIC, 160V 33UF M
C461 24591102 PLASTIC FILM, 50V 1000PF J
C464 24073124 100V 10U TOKUSHU 100YXG10MCA10X20
C466 24820273 PLASTIC FILM, 630V 27000PF J
C470 24794101 ELECTROLYTIC, 16V 100UF M
C472 24503049 PLASTIC FILM, 63V 0.47UF J
C473 24073081 ELECTROLYTIC, 50V 1.OUF M 3A
C483 #1 24590472 PLASTIC FILM, 50V 4700PF J
#2 24590123 PLASTIC FILM, 50V 0.012UF J
C484 #1 24082260 PLASTIC FILM, 100V 4700PF J
#2 24082257 PLASTIC FILM CQ922 M 100V 2700PF J
C501 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C502 24092743 CERAMIC CHIP, 10V F 0.47UF Z
C503 24794470 ELECTROLYTIC, 16V 47UF M
C504 24109103 CERAMIC CHIP, 50V B 0.01UF K
C511 24100104 CERAMIC CHIP, 25V F 0.1UF Z
SPECIFIC INFORMATIONS

Location Parts No. Descriptiopn
No.
Location Parts No. Descriptiopn
No.
– 19 –
C512 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C513 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C514 24794101 ELECTROLYTIC, 16V 100UF M
C516 24105110 CERAMIC CHIP, 50V CH 11PF J
C517 24092734 CERAMIC CHIP, 16V F 0.22UF Z
C522 24109103 CERAMIC CHIP, 50V B 0.01UF K
C524 24109103 CERAMIC CHIP, 50V B 0.01UF K
C526 24109222 CERAMIC CHIP, 50V B 2200PF K
C540 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C541 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C542 24100104 CERAMIC CHIP, 25V F 0.1UF Z
C601 24669479 ELECTROLYTIC, 50V 4.7UF M 3A
C602 24669479 ELECTROLYTIC, 50V 4.7UF M 3A
C603 24591561 PLASTIC FILM, 50V 560PF J
C604 24591561 PLASTIC FILM, 50V 560PF J
C605 24669100 ELECTROLYTIC, 50V 10UF M 3A
C606 24669100 ELECTROLYTIC, 50V 10UF M 3A
C607 24667470 ELECTROLYTIC, 25V 47UF M 3A
C608 24667470 ELECTROLYTIC, 25V 47UF M 3A
C609 24667470 ELECTROLYTIC, 25V 47UF M 3A
C611 24109102 CERAMIC CHIP, 50V B 1000PF K
C612 24668102 ELECTROLYTIC, 35V 1000UF M 3A
C613 24503042 PLASTIC FILM, 63V 0.12UF J
C614 24503042 PLASTIC FILM, 63V 0.12UF J
C615 24668102 ELECTROLYTIC, 35V 1000UF M 3A
C616 24668102 ELECTROLYTIC, 35V 1000UF M 3A
C618 24669479 ELECTROLYTIC, 50V 4.7UF M 3A
C619 24794471 ELECTROLYTIC, 16V 470UF M
C639 24793101 ELECTROLYTIC, 10V 100UF M
C667 24212102 CERAMIC DISC, 50V B 1000PF K
C668 24212102 CERAMIC DISC, 50V B 1000PF K
C669 24797330 ELECTROLYTIC, 50V 33UF M
C670 24797330 ELECTROLYTIC, 50V 33UF M
C801 24503507 PLASTIC FILM, AC275V 0.22UF K
C802 24503507 PLASTIC FILM, AC275V 0.22UF K
C805 24092281 CERAMIC DISC, AC250V E 4700PF
C806 24092281 CERAMIC DISC, AC250V E 4700PF
C807 24503049 PLASTIC FILM, 63V 0.47UF J
C808 24667101 ELECTROLYTIC, 25V 100UF M 3A
C809 24668339 ELECTROLYTIC, 35V 3.3UF M 3A
C810 24086059 ELECTROLYTIC, 400V 270UF M 3D
C812 24503041 PLASTIC FILM , 63V 0.1UF J
C813 24092555 CERAMIC DISC, AC250V E 1000PF M
C814 24092555 CERAMIC DISC, AC250V E 1000PF M
C817 24092339 CERAMIC DISC, 2KV 330PF K
C818 24095931 PLASTIC FILM, 1250VH 2200PF J
C819 24676220 ELECTROLYTIC, 100V 22UF M 3A
C821 24214471 CERAMIC DISC, 500V B 470PF K
C823 24214471 CERAMIC DISC, 500V B 470PF K
C829 24212272 CERAMIC DISC, 50V B 2700PF K
C840 24503049 PLASTIC FILM, 63V 0.47UF J
C841 24503047 PLASTIC FILM, 63V 0.33UF J
C842 24797470 ELECTROLYTIC, 50V 47UF M
C860 24794470 ELECTROLYTIC, 16V 47UF M
C861 24793470 ELECTROLYTIC CE04G 10V 47UF M
C884 24086916 ELECTROLYTIC, 160V 330UF M 3D
C885 24214471 CERAMIC DISC, 500V B 470PF K
C887 24214471 CERAMIC DISC, 500V B 470PF K
C889 24669222 ELECTROLYTIC, 50V 2200UF M 3A
C890 24667102 ELECTROLYTIC, 25V 1000UF M 3A
C893 24092337 CERAMIC DISC, 2KV 220PF K
C895 24669101 ELECTROLYTIC, 50V 100UF M 3A
C896 24214471 CERAMIC DISC, 500V B 470PF K
C898 24503045 PLASTIC FILM, 63V 0.22UF J
C902 24092349 CERAMIC DISC, 2KV R 2200PF K
C904 24436561 CERAMIC DISC, 50V SL 560PF J
C905 24436561 CERAMIC DISC, 50V SL 560PF J
C907 24436561 CERAMIC DISC, 50V SL 560PF J
C909 24679100 ELECTROLYTIC, 250V 10UF M 3A
C910 24797478 ELECTROLYTIC, 50V 0.47UF M
C911 24794100 ELECTROLYTIC, 16V 10UF M
C912 24073042 ELECTROLYTIC, 16V 1000UF M 3A
C913 24794101 ELECTROLYTIC, 16V 100UF M
C914 24212103 CERAMIC DISC, 50V B 10000PF K
C915 24092398 CERAMIC DISC, 25V 0.1UF Z
C930 24214101 CERAMIC DISC, 500V B 100PF K
C931 24214101 CERAMIC DISC, 500V B 100PF K
C4401 24109153 CERAMIC CHIP, 50V B 0.015UF K
C4402 24797229 ELECTROLYTIC, 50V 2.2UF M
C4403 24092730 CERAMIC CHIP, 16V B 0.1UF K
C4404 24794470 ELECTROLYTIC, 16V 47UF M
C4406 24092730 CERAMIC CHIP, 16V B 0.1UF K
C4412 24109473 CERAMIC CHIP, 25V B 0.047UF K
C4490 #1 24082908 PLASTIC FILM, 315V 0.12UF J
#2 24082906 PLASTIC FILM, 315V 0.1UF J
C5070 24109103 CERAMIC CHIP, 50V B 0.01UF K
C5100 24794101 ELECTROLYTIC, 16V 100UF M
CA01 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CA02 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CA03 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CA04 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CA06 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CA07 24105560 CERAMIC CHIP, 50V CH 56PF J
CA08 24105560 CERAMIC CHIP, 50V CH 56PF J
CA09 24109103 CERAMIC CHIP, 50V B 0.01UF K
CA10 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CA11 24794100 ELECTROLYTIC, 16V 10UF M
CA12 24092789 CERAMIC CHIP CK73B 6.3V 1UF K
CA13 24109103 CERAMIC CHIP, 50V B 0.01UF K
CA14 24794100 ELECTROLYTIC, 16V 10UF M
CA15 24794100 ELECTROLYTIC, 16V 10UF M
CA16 24794100 ELECTROLYTIC, 16V 10UF M
CA17 24092730 CERAMIC CHIP, 16V B 0.1UF K
CA18 24793470 ELECTROLYTIC CE04G 10V 47UF M
CB01 24797010 ELECTROLYTIC, 50V 1UF M
CB02 24105181 CERAMIC CHIP, 50V CH 180PF J
CB03 24794330 ELECTROLYTIC, 16V 33UF M
CB04 24109472 CERAMIC CHIP, 50V B 4700PF K
CB05 24105561 CERAMIC CHIP, 50V CH 560PF J
CB21 24503041 PLASTIC FILM , 63V 0.1UF J
CB22 24203470 ELECTROLYTIC, 16V 47UF M 7L 3A
CC01 24232103 CERAMIC DISC, 50V F 0.01UF Z
CC09 24109103 CERAMIC CHIP, 50V B 0.01UF K
CC26 24109103 CERAMIC CHIP, 50V B 0.01UF K
CC27 24109103 CERAMIC CHIP, 50V B 0.01UF K
CC30 24105470 CERAMIC CHIP, 50V CH 47PF J
CC31 24105470 CERAMIC CHIP, 50V CH 47PF J
CC60 24109223 CERAMIC CHIP, 25V B 0.022UF K
CC61 24109223 CERAMIC CHIP, 25V B 0.022UF K
CC62 24109102 CERAMIC CHIP, 50V B 1000PF K
CC63 24109102 CERAMIC CHIP, 50V B 1000PF K
CC64 24109102 CERAMIC CHIP, 50V B 1000PF K
CC65 24109102 CERAMIC CHIP, 50V B 1000PF K
CC66 24109102 CERAMIC CHIP, 50V B 1000PF K
CC67 24109102 CERAMIC CHIP, 50V B 1000PF K
CC68 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CS01 24797229 ELECTROLYTIC, 50V 2.2UF M
CS02 24797229 ELECTROLYTIC, 50V 2.2UF M
CS03 24797229 ELECTROLYTIC, 50V 2.2UF M
CS04 24797229 ELECTROLYTIC, 50V 2.2UF M
CS05 24797229 ELECTROLYTIC, 50V 2.2UF M
CS06 24797229 ELECTROLYTIC, 50V 2.2UF M
CS07 24797229 ELECTROLYTIC, 50V 2.2UF M
CS08 24797229 ELECTROLYTIC, 50V 2.2UF M
CS18 24794100 ELECTROLYTIC, 16V 10UF M
CS19 24794100 ELECTROLYTIC, 16V 10UF M
CS20 24797478 ELECTROLYTIC, 50V 0.47UF M
CV02 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CV03 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CV04 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CV05 24109103 CERAMIC CHIP, 50V B 0.01UF K
CV06 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CV08 24763221 ELECTROLYTIC, 16V 220UF M
CV12 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CV23 24203101 ELECTROLYTIC, 16V 100UF M 7L 3A
CV24 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CV25 24794220 ELECTROLYTIC, 16V 22UF M
CV26 24109473 CERAMIC CHIP, 25V B 0.047UF K
CV27 24203101 ELECTROLYTIC, 16V 100UF M 7L 3A
CV28 24100104 CERAMIC CHIP, 25V F 0.1UF Z
CV46 24212332 CERAMIC DISC, 50V B 3300PF K
CV47 24212332 CERAMIC DISC, 50V B 3300PF K
SPECIFIC INFORMATIONS

Location Parts No. Descriptiopn
No.
Location Parts No. Descriptiopn
No.
– 20 –
RESISTORS
R101 24553223 OXIDE METAL FILM, 1W 22K OHM J
R102 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R103 24011433 CHIP, METAL FILM, 1/20W 43K OHM J
R104 24011271 CHIP, METAL FILM, 1/20W 270 OHM J
R105 24000445 CHIP JUMPER, 1608TYPE
R106 24011682 CHIP, METAL FILM, 1/20W 6.8K OHM J
R107 24011122 CHIP, METAL FILM, 1/20W 1.2K OHM J
R108 24011471 CHIP, METAL FILM, 1/20W 470 OHM J
R109 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R110 24872360 CHIP, METAL FILM, 1/16W 36 OHM J
R112 24011562 CHIP, METAL FILM, 1/20W 5.6K OHM J
R113 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R114 24011471 CHIP, METAL FILM, 1/20W 470 OHM J
R116 24011681 CHIP, METAL FILM, 1/20W 680 OHM J
R117 24872360 CHIP, METAL FILM, 1/16W 36 OHM J
R122 24011221 CHIP, METAL FILM, 1/20W 220 OHM J
R123 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R124 24011331 CHIP, METAL FILM, 1/20W 330 OHM J
R125 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R126 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R127 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R128 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R129 24011272 CHIP, 1/20W 2.7K OHM J
R130 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R131 24011221 CHIP, METAL FILM, 1/20W 220 OHM J
R132 24011684 CHIP, METAL FILM, 1/20W 680K OHM J
R135 24000445 CHIP JUMPER, 1608TYPE
R204 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R208 24011683 CHIP, METAL FILM, 1/20W 68K OHM J @U902
24366103 CARBON FILM, 1/6W 10K OHM J @U903A
R209 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J @U902
24366103 CARBON FILM, 1/6W 10K OHM J @U903A
R211 24366623 CARBON FILM, 1/6W 62K OHM J
R216 24872103 CHIP, METAL FILM, 1/16W 10K OHM J
R217 24366392 CARBON FILM, 1/6W 3.9K OHM J
R218 24011101 CHIP, METAL FILM, 1/20W 100 OHM J @U902
24366223 CARBON FILM, 1/6W 22K OHM J @U903A
R219 24011101 CHIP, METAL FILM, 1/20W 100 OHM J @U902
24366203 CARBON FILM, 1/6W 20K OHM J @U903A
R220 24011101 CHIP, METAL FILM, 1/20W 100 OHM J
R227 #1 24366333 CARBON FILM, 1/6W 33K OHM J
#2 24366303 CARBON FILM, 1/6W 30K OHM J
R271 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R272 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R300 #1 24000525 METAL FILM, 1/4W 4.7K OHM F
#2 24367472 CARBON FILM, 1/6W 4.7K OHM G
R301 #1 24367681 CARBON FILM, 1/6W 680 OHM G
#2 24367472 CARBON FILM, 1/6W 4.7K OHM G
R302 #1 24000525 METAL FILM, 1/4W 4.7K OHM F
#2 24367472 CARBON FILM, 1/6W 4.7K OHM G
R305 24322109 OXIDE METAL FILM, 1W 1 OHM J
R321 24011104 CHIP, METAL FILM, 1/20W 100K OHM J @U902
24366224 CARBON FILM, 1/6W 220K OHM J @U903A
R322 24011333 CHIP, METAL FILM, 1/20W 33K OHM J @U902
24366274 CARBON FILM, 1/6W 270K OHM J @U903A
R325 24011334 CHIP, METAL FILM, 1/20W 330K OHM J
R326 24338109 OXIDE METAL FILM, 1W 1 OHM J
R327 24338109 OXIDE METAL FILM, 1W 1 OHM J
R336 #1 24382181 OXIDE METAL FILM, 1W 180 OHM J
#2 24382271 OXIDE METAL FILM, 1W 270 OHM J
R337 #1 24000525 METAL FILM, 1/4W 4.7K OHM F
#2 24367472 CARBON FILM, 1/6W 4.7K OHM G
R362 24011823 CHIP, METAL FILM, 1/20W 82K OHM J
R363 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R364 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R365 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R366 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R367 24011471 CHIP, METAL FILM, 1/20W 470 OHM J
R368 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R369 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R370 24366822 CARBON FILM, 1/6W 8.2K OHM J
R371 24366103 CARBON FILM, 1/6W 10K OHM J
R372 24366220 CARBON FILM, 1/6W 22 OHM J
R373 24366103 CARBON FILM, 1/6W 10K OHM J
R374 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R375 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R376 24011104 CHIP, METAL FILM, 1/20W 100K OHM J
R377 24011563 CHIP, METAL FILM, 1/20W 56K OHM J
R378 24011822 CHIP, METAL FILM, 1/20W 8.2K OHM J
R379 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R400 24946561 CARBON COMPOSITION, 1/2W 560 OHM K
R401 24946223 CARBON COMPOSITION GF 1/2W 22K K
R405 24553682 OXIDE METAL FILM, 1W 6.8K OHM J
R410 24366271 CARBON FILM, 1/6W 270 OHM J
R411 24366331 CARBON FILM, 1/6W 330 OHM J
R414 24531560 FUSIBLE, 1/2W 56 OHM J
R415 24553472 OXIDE METAL FILM, 1W 4.7K OHM J
R417 #1 24510512 CERAMIC COVERED, 5W 5.1K OHM J
#2 24510562 CERAMIC COVERED, 5W 5.6K OHM J
R425 24366561 CARBON FILM, 1/6W 560 OHM J
R426 24366751 CARBON FILM, 1/6W 750 OHM J
R427 24366392 CARBON FILM, 1/6W 3.9K OHM J
R428 24366561 CARBON FILM, 1/6W 560 OHM J
R431 24366103 CARBON FILM, 1/6W 10K OHM J
R432 24366473 CARBON FILM, 1/6W 47K OHM J
R433 24366681 CARBON FILM, 1/6W 680 OHM J
R434 24366472 CARBON FILM, 1/6W 4.7K OHM J
R441 24532102 FUSIBLE, 1W 1K OHM J
R445 24546229 FUSIBLE, 1/2W 2.2 OHM J
R451 24011123 CHIP, METAL FILM, 1/20W 12K OHM J
R452 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J
R462 24366103 CARBON FILM, 1/6W 10K OHM J
R463 24366152 CARBON FILM, 1/6W 1.5K OHM J
R464 24366102 CARBON FILM, 1/6W 1K OHM J
R465 24011682 CHIP, METAL FILM, 1/20W 6.8K OHM J
R469 24338569 METAL FILM 1W 5R6 J
R470 24338568 OXIDE METAL FILM, 1W 0.56 OHM J
R471 24381271 OXIDE METAL FILM, 1/2W 270 OHM J
R472 24366101 CARBON FILM, 1/6W 100 OHM J
R473 24366183 CARBON FILM, 1/6W 18K OHM J
R474 24376393 CARBON FILM, 1/2W 39K OHM J
R476 24366471 CARBON FILM, 1/6W 470 OHM J
R477 24366102 CARBON FILM, 1/6W 1K OHM J
R479 24381680 OXIDE METAL FILM, 1/2W 68 OHM J
R483 #1 24366104 CARBON FILM, 1/6W 100K OHM J
#2 24366224 CARBON FILM, 1/6W 220K OHM J
R484 #1 24366823 CARBON FILM, 1/6W 82K OHM J
#2 24366683 CARBON FILM, 1/6W 68K OHM J
R490 24366101 CARBON FILM, 1/6W 100 OHM J
R491 24366101 CARBON FILM, 1/6W 100 OHM J
R492 24366332 CARBON FILM, 1/6W 3.3K OHM J
R503 24366331 CARBON FILM, 1/6W 330 OHM J
R506 24011473 CHIP, METAL FILM, 1/20W 47K OHM J
R511 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R512 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R514 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R515 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R516 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R517 24011102 CHIP, METAL FILM, 1/20W 1K OHM J
R521 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R522 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R523 24011222 CHIP, METAL FILM, 1/20W 2.2K OHM J
R601 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R602 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R603 24011123 CHIP, METAL FILM, 1/20W 12K OHM J
R604 24011123 CHIP, METAL FILM, 1/20W 12K OHM J
R607 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R608 24011223 CHIP, METAL FILM, 1/20W 22K OHM J
R609 24366229 CARBON FILM, 1/6W 2.2 OHM J
R610 24366229 CARBON FILM, 1/6W 2.2 OHM J
R611 24011104 CHIP, METAL FILM, 1/20W 100K OHM J
R618 24011103 CHIP, METAL FILM, 1/20W 10K OHM J
R619 24011224 CHIP, METAL FILM, 1/20W 220K OHM J
R661 24552221 OXIDE METAL FILM, 1/2W 220 OHM J
R662 24552221 OXIDE METAL FILM, 1/2W 220 OHM J
R801 24004716 METAL GLAZE 1/2W 2R2M J
R803 24553683 OXIDE METAL FILM, 1W 68K OHM J
R805 24366221 CARBON FILM, 1/6W 220 OHM J
R808 24019484 THERMISTOR, PTC, AC265 4R5A
R810 24366102 CARBON FILM, 1/6W 1K OHM J
R815 24366102 CARBON FILM, 1/6W 1K OHM J
SPECIFIC INFORMATIONS