Touchboards peerless-AV PRS-KIT0811 Guide

Installation and Assembly
Model: PRS-KIT0811, PRS-KIT1420, PRS-KIT2026
ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Max UL Load Capacity: 25 lb (11.3 kg)

2 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill with 5/16" and 5/32" drill bits
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings...............................................4
Installation to Concrete Ceilings.............................................................................................................................................5
Installation of Extension/Adjuster Tube Assembly .................................................................................................................6
Installation to Extension Column ...........................................................................................................................................7
Attaching Adapter Plate to Projector ......................................................................................................................................7
Installation of Projector...........................................................................................................................................................8
Projector Alignment ................................................................................................................................................................9
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by a qualified professional.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with
the hardware included in this product as specified in the installation sheet. To mount this product to an alternative
supporting surface, contact Peerless customer care at 1 800 865-2112.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Joist Included
• Wood Beam Included
• Solid Concrete Included
• Other or unsure? Contact Qualified Professional (not evaluated by UL)
WARNING

3 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
E
F
G
Parts List PRS-KIT0811 PRS-KIT1420 PRS-KIT2026
Description Qty. Part # Part # Part #
Aextension tube 1 154-1099 154-1100 154-1101
Badjuster tube 1 154-1095 154-1096 154-1096
CM8 x 10 mm phillips screw 2 520-1605 520-1605 520-1605
DM5 x 10 mm phillips screw 1 520-9250 520-9250 520-9250
Eceiling plate 1 580-1042 580-1042 580-1042
Fprojector mount assembly 1 054-1174 054-1174 054-1174
Guniversal adapter plate 1 055-1938 055-1938 055-1938
Hflat washer 2 540-1078 540-1078 540-1078
I#14 x 2.5 phillips hex head wood screw 2 5S1-015-C03 5S1-015-C03 5S1-015-C03
Jconcrete anchor 2 590-0320 590-0320 590-0320
K4 mm security t-wrench 1 560-1718 560-1718 560-1718
L#10-32 x 1/4" socket pin screw 1 520-1196 520-1196 520-1196
MM3 x 8 mm socket pin serrated washer head screw 4 510-1004 510-1004 510-1004
NM4 x 10 mm socket pin serrated washer head screw 4 510-1060 510-1060 510-1060
OM5 x 10 mm socket pin serrated washer head screw 4 510-1126 510-1126 510-1126
PM6 x 10 mm socket pin serrated washer head screw 4 510-1066 510-1066 510-1066
Q#6 flat washer 4 540-1025 540-1025 540-1025
R2 mm security allen wrench 1 560-1097 560-1097 560-1097
D
HIJ
L
K
ABC
NOTE: Parts shipped assembled.
MNO
PQ
R
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.

4 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
I
I
E
WOOD JOIST
CEILING
Drill two 5/32" (4mm) dia. holes to a minimum depth of 2.5" (64mm). Attach ceiling plate (E) with two #14 x 2.5"
(6mm x 65mm) wood screws (I) as shown using a 3/8" (10mm) socket wrench. Tighten wood screws (I) so ceiling
plate (E) is firmly attached.
Installation to Wood Joist Finished Ceilings, Exposed Wood Joists, or
Wood Beam Ceilings
1
Skip to step 2 on page 6.
• Tighten wood screws so that ceiling plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into
the center of the joist. The use of an "edge to edge"
stud finder is highly recommended.
WARNING

5 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
CONCRETE CEILING
Place ceiling plate (E) on ceiling as a template and
mark the center of the two mounting holes. Drill
two 5/16" (8mm) dia. holes to a minimum depth
of 2.5" (64mm). Attach ceiling plate (E) using two
concrete anchors (J) and #14 x 2.5" wood screws
(I). Tighten wood screws (I) using a 3/8" (10mm)
socket wrench, phillips screwdriver or 10mm open
end wrench until ceiling plate (E) is firmly attached.
Installation to Concrete Ceilings
1
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
I
E
J
CUTAWAY VIEW
INCORRECT CORRECT
plaster/
drywall
plaster/
drywall
concrete concrete
1
3
2
J
Drill holes and insert anchors (J).
Place plate (E) over anchors (J) and secure with screws (I).
Tighten all fasteners.
E
J
I
concrete
surface
E
E
WARNING
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage screws, greatly reducing
their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete anchors directly to load-
bearing concrete.
• Never attach concrete anchors to concrete covered
with plaster, drywall, or other finishing material.
If mounting to concrete surfaces covered with a
finishing surface is unavoidable (not evaluated by
UL), the finishing surface must be counterbored
as shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywall is thicker than 5/8", custom fasteners
must be supplied by installer. (not evaluated by UL)
WARNING
WARNING

6 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
There are two M8 x 10mm phillips screws (C)
that secure the extension tube (A) to the adjuster
tube (B). Loosen the M8 x 10mm phillips screw
(C) on the hook slot side of the adjuster tube (B)
and remove the other screw as shown in figure
3.1. Rotate extension tube (A)and slide down into
desired hook slot. Replace the M8 x 10mm phillips
screw (C) as shown in figure 3.2. Tighten both
screws.
Installation of Extension/Adjuster Tube Assembly
Thread adjuster tube (B) into threaded fitting on
ceiling plate (E) as shown in figure 2.1. Tighten
securely aligning slot in end of adjuster tube (B)
with one of the holes in the side of threaded fitting
on ceiling plate (E). Insert and tighten one
M5 x 10mm phillips screw (D) to lock adjuster tube
(B) to threaded fitting on ceiling plate (E) as shown
in figure 2.2.
2
3
figure 2.1
B
E
figure 2.2
E
D
B
figure 3.1
LOOSEN
(DO NOT REMOVE)
figure 3.2
C
A
C
HOOK
SLOT
B
• Installer must verify that the ceiling will safely sup-
port the combined weight of all attached equipment
and hardware.
• Adjuster tube (B) must be fully threaded (six or
seven full turns) onto threaded fitting in ceiling plate
and then locked with screw (C).
WARNING
WARNING

7 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
Installation to Extension Column
Screw projector mount assembly (F) onto extension tube (A). Tighten swivel stop screw against extension tube
using t-wrench (K). NOTE: The swivel stop screw is used to jam against threads of extension tube (A) to prevent
any excess movement of projector mount assembly (F). Do not overtighten screw; overtightening screw will
damage threads making it difficult to separate products.
F
SWIVEL STOP SCREW
BACK OF MOUNT
A
4
GENERIC PROJECTOR
Note: The projector you are installing may differ in appearance from the sample illustrated below.
Place projector upside down. Locate adapter plate (G) with notch facing forward as close to projector center of
gravity as possible without covering any mounting holes. Loosen channels using t-wrench (K), and if there are
only three mounting holes remove fourth channel. Using one channel for each mounting hole, position feet of
channels over mounting holes as shown below. IMPORTANT: If projector does not have at least three mounting
holes, do not use this adapter plate.
NOTE: Some projectors have feet which can be removed and the corresponding threaded insert can be used for a
mounting hole.
NOTE: Once channels are in position retighten fasteners.
*Notch indicates front of projector.
*
MOUNTING HOLE
G
5
CHANNEL
FOOT OF CHANNEL
Attaching Adapter Plate to Projector

8 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
Slide connection block of adapter plate (G) with projector into projector mount assembly (F) as shown. Tighten
captive screw to secure projector to projector mount assembly (F).
Installation of Projector
CAPTIVE SCREW
F
FRONT OF MOUNT
CONNECTION BLOCK
G
7
Attach adapter plate (G) to projector using one screw (M, N, O or P) for each channel as shown below. Tighten
all screws, while keeping the center of gravity. Be sure that adapter plate (G) is straight. Adjust the feet of the
channels to keep the adapter plate level. Tighten all screws using t-wrench (K) while keeping the center of
gravity. If M3 screws (M) are used, tighten using 2mm security allen wrench (R).
NOTE: Projectors will require different size screws for mounting. Use a combination of screws (M, N, O or P)
and foot adjustment that will result in channels of adapter plate (G) fitting tightly against projector.
IMPORTANT: In order to properly engage the threads in the mounting holes, the screw must be turned at least
3 full turns. NOTE: If using screw (M), place washer (Q) between screw (M) and foot of channel.
• It is the responsibility of the installer to ensure that
the projector is properly ventilated. Feet of channels
are used to raise the mount off the projector surface.
CAUTION
6
G
M, N,
O or P
FOOT OF
CHANNEL
• Always use an assistant or mechanical lifting
equipment to safely lift and position the projector.
WARNING

9 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
Projector Alignment
To adjust yaw (swivel): Loosen screw on projector mount assembly (F) indicated below until projector mount can
be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Loosen two screws on projector mount assembly (F) indicated be-
low. Tilt mount to desired position and retighten screws.
To adjust roll (side to side tilt): Loosen two screws on projector mount assembly (F) indicated below. Tilt mount
to desired position and retighten screws.
IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (L) through projector mount as-
sembly (F) and into connection block as shown.
F
CONNECTION BLOCK
L
SCREW FOR SWIVEL STOP
F
SCREWS FOR ROLL ADJUSTMENT
SCREWS FOR PITCH
ADJUSTMENT
8
9
© 2012, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerlessmounts.com

10 of 10 ISSUED: 06-02-05 SHEET #: 054-9124-11 01-27-12
© 2012 Peerless Industries, Inc.
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
This warranty gives specific legal rights, and you may also have other rights which vary from state to state.
LIMITED FIVE-YEAR WARRANTY
www.peerlessmounts.com