on stage SMS4500Pv2 Manual

SMS4500Pv2
Desktop Monitor Stands
Assembly and Set Up Instructions
A
Medium Bolt (x2)
B
Large Bolt (x2)
M
Rubber Feet (x8)
K
Lower-Shaft Bolt (x2)
F
Angle-Adjustment
Knob (x2)
E
Nut (x2)
G
Shaft (x2)
H
Platform with
Pad (x2)
J
Height-Adjustment
Pin (x2)
L
Base (x2)
I
Allen Key (x1)
C
Large Washer (x2)
D
Medium Washer (x2)
N
Desktop Clamp (x2)
Components (drawings not to scale):
Please follow all instructions carefully.
CAUTION
EXCEEDING THE WEIGHT CAPACITY OR FAILURE TO OBSERVE PROPER ASSEMBLY INSTRUCTIONS AND
WARNINGS MAY CAUSE BODILY INJURY OR EQUIPMENT DAMAGE AND WILL VOID THE PRODUCT WARRANTY.
© 2021 The Music People, a division of JAM Industries USA, LLC.

BEFORE ASSEMBLY: Remove all contents from the box and identify the components using the diagrams.
Instructions:
1. Remove both bolts (A, B), both washers (C, D), the nut
(E), and the angle-adjustment knob (F) from the bracket
at the upper end of the shaft (G).
4. Insert the medium bolt (A) through
the smaller holes of both brackets, then
through the medium washer (D). Screw
the nut (E) onto the bolt.
5. Insert the large bolt (B) through the larger
holes of both brackets, then through the large
washer (C). Screw the angle-adjustment knob
(F) onto the bolt.
2. Loosen the clutch knob on the lower section of the
shaft (G). Slide the upper shaft section to its longest
setting. Insert the height-adjustment pin (J) into the
hole closest to the clutch. Lower the upper shaft section
slightly so that the pin rests on the clutch. Tighten the
clutch knob to prevent movement.
3. Slide the platform (H) bracket inside the
shaft (G) bracket. Align the holes of the
brackets as shown.
Large bolt (B)
Medium bolt (A)
The square part of the
large bolt (B) must be
seated inside the hole.
© 2021 The Music People, a division of JAM Industries USA, LLC.
6. Remove the lower-shaft bolt (K) from the
bottom of the shaft (G) using the allen key (I).
For use with the base:
7. Place the base (L) on the bottom
of the shaft (G) with the recess for the
bolt head facing away from the shaft.
Align the center hole of the base with
the hole on the bottom of the shaft.
Insert the lower-shaft bolt (K) through
the base and into the shaft. Tighten
the bolt using the allen key (I).
8. Screw the four rubber feet (M) into the holes at the
corners of the base (L). The rubber part of the feet should
be on the bottom of the base, facing away from the shaft.
© 2021 The Music People, a division of JAM Industries USA, LLC.
9. Place the unit upright on its feet.
10. To adjust the stand’s height, loosen
the clutch knob on the lower section of
the shaft (G). Slide the upper shaft section
to the desired height. Insert the height-
adjustment pin (J) into the hole closest to
the clutch. Lower the upper shaft section
slightly so that the pin rests on the clutch.
Tighten the clutch knob.
Do not adjust the height with a speaker on the stand.
11. To adjust the angle of the platform, loosen the
angle-adjustment knob (F). Tilt the platform to the
desired angle. Tighten the angle-adjustment knob.
Do not adjust the platform angle with a speaker on the stand.

For use with the desktop clamp:
12. Place the desktop clamp (N) on the
bottom of the shaft (G) with the clamp
knob pointing away from the shaft. Align
the center hole on top of the clamp with
the hole on the bottom of the shaft. Insert
the lower-shaft bolt (K) through the clamp
and into the shaft. Tighten the bolt using
the allen key (I).
13. To mount the stand to a desktop, loosen the knob
on the desktop clamp (N) until there is clearance for
the thickness of the desktop. Slide the clamp onto the
desktop. Tighten the clamp knob.
© 2021 The Music People, a division of JAM Industries USA, LLC.