Toyota RS3200 PLUS User manual

2003- MR2 SPYDER TVIP V5 RS3200 PLUS
OWNER’S GUIDE
R emote K eyless
Security system
Designed Specifically for y our Vehicle
owner’s guide
RS3200
090002-25200700
Rev. A 6/07/02
FOR MR2-SPYDER
PLUS

Page 12 TOYOTA RS3200 PLUS Security system
To better understand the features and functions of this security system, please read this
Owner’s Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTION PAGE
INTRODUCTION 2
BRIEF DESCRIPTION–RS3200 PLUS FEATURES 3, 4
OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING) 5
DISARMING THE RS3200 PLUS(except PASSIVE DISARMING) 6
PASSIVE (AUTOMATIC) ARMING & DISARMING 7
AUTOMATIC REARMING 8
ALARM INFORMATION
ALARM TRIGGERS 9
ALARM DESCRIPTIONS 10
STOPPING AN ALARM 10
RADAR SENSOR INFORMATION 11
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 12
WARNING AND CAUTION INFORMATION 13
TOYOTA RS3200 PLUS Security system Page 1
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 PLUS is factory-set to not PASSIVELY ARM. To change the system’s operation for
PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For
more information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
a. Using the remote control,
lock, then unlock the
doors 3 times.
b. Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = PASSIVE ARMING OFF
3 times = PASSIVE ARMING ON,
0 Sec. ENTRY DELAY
4 times = PASSIVE ARMING ON,
15 Sec. ENTRY DELAY
5 times = PASSIVE ARMING ON,
30 Sec. ENTRY DELAY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the
door in 2 seconds; if this
does not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is
now complete.
e. Unlock the driver’s door
inside lock button.

INTRODUCTION
Congratulations on your choice of the RS3200 PLUS security system to protect your vehicle! To
get the most from the system, we strongly recommend that you read this Owner’s Guide complete-
ly to learn all of its features and functions.
The RS3200 PLUS provides comprehensive security protection through point-of-entry monitoring,
intrusion detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and
sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when someone
intrudes into the vehicle. This system is a vehicle theft deterrent and will not prevent theft of
personal goods in vehicle. For additional security, it is recommended that the vehicle top
be in the closed position. During the ALARM, the vehicle’s horn will sound and the headlights,
tail lights and front marker lights will flash. A lso, the vehicle’s starter is disabled, to prevent engine
start.
An important note about your system
Throughout this guide, there are references to the STATUS MONITOR for this system. This panel
holds the LED indicator (for the system’s operating status). In vehicles with an engine immobilizer,
there is already a LED installed in the vehicle. If your vehicle falls into this category, remember
to look at that LED when the information refers to the STATUS MONITOR. If you do not know where
the LED is located, refer to your vehicle’s owner’s guide for specific information.
* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will
elapse when a door is opened before an ALARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
Page 2 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 11
123
123
RADAR SENSOR INFORMATION
RADAR SENSOR CHECK PROCEDURE
1. ARM the system.
Press the LOCK button on the remote control or lock the doors
with the key.
(Remember, the system will not ARM if any door is open.)
2. Wait until the STATUS MONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or hatch
is closed.
3. Move inside the vehicle.
When movement occurs inside the vehicle, A WARN AWAY ALARM
activates for 20 seconds. If sensor detects 2nd movement within 60
seconds after the 1st warn away alarm trigger, then a regular ALARM
activates for 60 seconds.
Note: If you find that the system does not perform as expected,
contact your Toyota dealer for more information.
4. DISARM the system to stop the WARN AWAYALARM.
Press the UNLOCK button on the remote control or use the key to
DISARM the system.
RADAR SENSOR OFF MODE
THE RADAR SENSOR CAN BEDEACTIVATED. PERFORM THE
FOLLOWING: PUSH THE SENSOR OFF SWITCH ON THE INSTRUMENT PANEL
BEFORE ARMING BY KEY OR REMOTE CONTROL.
IMMOBILIZER LED STARTS BLINKING.
ARM THE SYSTEM WITH THE REMOTE CONTROL OR KEY WHILE THE
IMMOBILIZER LED IS BLINKING.
THE RADAR SENSOR WILL DEACTIVATE DURING ARMING.
NOTE: IFYOU DISARM THE SYSTEM AFTER YOU SET THE RADARSENSOR
OFF, YOU HAVETO REPEAT THE ABOVE PROCEDURE WHEN YOU ARM THE
SYSTEM IF YOU WANT TO DEACTIVATE THE RADAR SENSOR AGAIN. THE
SYSTEM WILL AUTOMATICALLY CANCEL THE RADAR SENSOR OFF MODE
WHEN DISARMED.
OFF

Page 10 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 3
FEATURES FUNCTIONS
The RS3200 PLUS will ARM 30 seconds after the LOCK button on the
remote control is pressed, and DISARM when the UNLOCK button is
pressed. If your vehicle is equipped with a buzzer that chirps when
the lock and unlock buttons on the remote controls are pressed, the
buzzer will also chirp when the system is REMOTE ARMED and
DISARMED.
The RS3200 PLUS will automatically RELOCK the vehicle’s doors if no
door is opened within 30 seconds after REMOTE DISARMING, then will
REARM 30 seconds later.
The RS3200 PLUS will ARM 30 seconds after you close the trunk (if
open) and lock the vehicle’s doors with the key, and will DISARM when
you unlock a door with the key.
The RS3200 PLUS may be programmed to automatically ARM 30
seconds after the ignition key is removed, the vehicle exited and the
last doorand the trunk closed, without the necessity of locking the
doors.
The RS3200 PLUS may be DISARMED with the vehicle’s ignition key
after it was PASSIVELY ARMED.
When the RS3200 PLUS has been PASSIVELY ARMED, an ENTRY
D
ELAY (user-selectable at 0, 15, or 30 seconds) will start when a door
is opened before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a
door is open), the RS3200 PLUS will ARM 30 seconds after you close
all the doors and the trunk (if open).
The RS3200 PLUS may be DISARMED by inserting the key into the
ignition switch and turning it to “ON.”
Forcibly unlocking or opening a door, hatch or trunk while the
RS3200 PLUS is ARMED will TRIGGER an ALARM immediately. (If the
system was PASSIVELY ARMED,the ENTRY DELAY must pass before the
ALARM is TRIGGERED.)
The RS3200 PLUS utilizes RADAR SENSOR to sense the intrusion
from outside, and TRIGGER an ALARM . It is fine tuned to detect
unauthorized movement inside the vehicle.
When RADAR SENSOR detects the intrusion, it TRIGGERS a WARN
A
WAY ALARM; the headlights and tail and marker lights flash, and the
horn sounds for 20 seconds, but the starter is not disabled. If there is
another detection of a door is opened or unlocked without a key, the
regular ALARM is TRIGGERED.
While ARMED, the RS3200 PLUS monitors the ignition switch. If an
attempt is made to start the vehicle without a key, an ALARM is trig-
gered.
REMOTE
ARMING/DISARMING
AUTOMATIC
REARMING
KEY
ARMING/DISARMING
PASSIVE (AUTOMATIC)
ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
RADAR SENSOR
WARN AWAY ALARM
IGNITION SWITCH
MONITORING
BRIEF DESCRIPTION–RS3200 PLUS FEATURES
ALARM INFORMATION
ALARM DESCRIPTIONS
Regular ALARM
When an ALARM is triggered in any way other than initial detection by the RADAR SENSOR,
the following occur:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The starter is disabled (no engine start) until the system is DISARMED.
The door lock will be relocked if someone reaches in and unlocks the inside lock button.
After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.
WARN-AWAYALARM
Upon initial detection of noise when sensor detects intrusion.
The horn sounds repeatedly for 20 seconds.
The headlights flash repeatedly for 20 seconds.
The tail and marker lights flash repeatedly for 20 seconds.
The interior lights turn on for 20 seconds.
If the RADAR SENSOR detects noise again within one minute, or if a door or trunk or hatch is opened
while the system is still ARMED, the regular ALARM (described above) is activated.
STOPPING AN ALARM
Simply DISARM the system using the remote control or key as described on page 6.
THE HORN SOUNDS
FOR 20 SECONDS
HEADLIGHTS FLASH
FOR 20 SECONDS
MARKER LIGHTS FLASH
FOR 20 SECONDS
TAIL LIGHTS FLASH
FOR 20 SECONDS
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH
FOR 60 SECONDS
THE STARTER IS DISABLED
UNTIL THE SYSTEM IS DIS-
ARMED
MARKER LIGHTS FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 20 SECONDS
123
123
123
123

Page 4 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 9
FEATURES FUNCTIONS
When an ALARM is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (DISARMED).
During an ALARM, the system will lock the doors if one is unlocked,
and will continue to do so for the duration of the ALARM.
The user is notified that an ALARM occurred. Upon DISARMING the
system after an ALARM was TRIGGERED, the vehicle’s tail and marker
lights will be turned on, and the BUZZER sounds, for 2 seconds.
The RS3200 PLUS flashes the vehicle’s tail and marker lights during
REMOTE ARMING and REMOTE DISARMING,as well as during an ALARM.
Also, the headlights flash during an ALARM.
During an ALARM,the RS3200 PLUS activates the vehicle’s horn.
If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM
is TRIGGERED once power is restored.
This panel houses the flashing LED that indicates the operating status
of the security system. (In vehicles with an engine immobilizer system,
that system’s LED and a separate microphone are used instead.)
STARTER DISABLE
FORCED LOCK
DURING ALARM
TRIGGER MEMORY
EXTERIOR LIGHT
ACTIVATION
HORN ACTIVATION
POWER LOSS
MEMORY
STATUS MONITOR
BRIEF DESCRIPTION–RS3200 PLUS FEATURES ALARM INFORMATION
ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
Forcibly opening a door without a key
Manually unlocking a door
Manually operating an inside lock button will TRIGGER an ALARM.
Note: Because this action will TRIGGER an ALARM, it is important
that you do not ARM the system while someone is in the
vehicle.
“Hot wiring” the vehicle
The RS3200 PLUS can detect the absence of the ignition key if the
ignition circuit is shorted in attempt to start the vehicle.
Intrusion Detection
When the radar sensor detects intrusion, it TRIGGERS a WARN AWAY
ALARM first, then a regular ALARM. See the description of how the
RADAR SENSOR TRIGGERS ALARMS on page 11.
Power restoration
If power to the system is interrupted while it is ARMED, an ALARM will
be TRIGGERED immediately when power is restored.
123
123
123
123
123

Page 8 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 5
OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The STATUS MONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.
Close the trunk or hatch, if necessary.
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The STATUS MONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
THE BUZZER CHIRPS ONCE WHEN
THE SYSTEM IS REMOTE ARMED
123
123
123
123
123
123
123
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
123
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 PLUS is DISARMED at the same
time. However, if you do not open a door or the trunk or hatch within 30 seconds, the system will
relock the doors and the RS3200 PLUS will REARM 30 seconds later
0
15
30
45
THE DOORS ARE
UNLOCKED BY PRESSING
THE UNLOCK BUTTON ON
THE REMOTE CONTROL...
WHEN NO DOOR, TRUNK
OR HATCH IS OPENED...
FOR MORE THAN 30
SECONDS...
THE RS3200 PLUS
AUTOMATICALLY RELOCKS
THE DOORS, THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP
FOR 30 SECONDS
(PRE-ARM), THEN
FLASHES WHEN THE
SYSTEM IS ARMED

Page 6 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 7
OPERATION
DISARMING THE RS3200 PLUS (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the door key switch and turn it toward the
rear of the vehicle:
The IMMOBILIZER LED stops flashing. The system
is now DISARMED.*
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The STATUS MONITOR’SLED stops flashing. The system
is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The STATUS MONITOR’SLED stops flashing. The system
is now DISARMED.*
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer
sounds for 2 seconds when the system is DISARMED, the
TRIGGER MEMORY was activated; an ALARM was TRIGGERED while
you were away from the vehicle.
* Please note, if the system utilizes your vehicle’s engine immobilizer system LED instead of the
STATUS MONITOR, the LED will continue to flash.
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO
DISARM THE SYSTEM
THE DRIVER’SDOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE
DISARMED
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-
RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM
IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS
REMOTE DISARMED
123
123
123
123
123
123
123
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
123
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 PLUS is programmed to PASSIVELY ARM, the system will ARM after the igni-
tion key is removed and all doors and the trunk or hatch are closed; you do not need to lock the
doors. When you come back to your vehicle and open a door, you must insert the key into the
ignition switch and turn it to “ON” during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will
be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no
ENTRY DELAY. See the PROGRAMMING section on page 15 to activate the PASSIVE ARMING mode,
as well as select the ENTRY DELAY time.
To PASSIVELY ARM the system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (The system will not ARM
while any of the doors are open.)
After the last door is closed:
The STATUS MONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
To DISARM the PASSIVELY ARMED system:
Enter the vehicle through a front door.
The ENTRY DELAY begins:
The STATUS MONITOR’SLED turns on (no flashing.)
Insert the key into the ignition switch and turn it to
“ON” before the
ENTRY DELAY ends.*
The LED turns off. The system is now DISARMED.
You may also DISARM the system following any of the methods
described on page 7.
NOTE: If your vehicle’s tail and marker lights turn on and the
buzzer sounds for 2 seconds when the system is
DISARMED, the TRIGGER MEMORY was activated; an ALARM
was TRIGGERED while you were away from the vehicle.
* If the ENTRY DELAY time elapses before the ignition switch is turned to “ON”, an ALARM will be
TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to “ON”, or
press and release the remote control’s UNLOCK button.
THE SYSTEM ARMS 30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR, TRUNK OR HATCH)
IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN
IT TO “ON”
123
123
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
123

Page 6 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 7
OPERATION
DISARMING THE RS3200 PLUS (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the door key switch and turn it toward the
rear of the vehicle:
The IMMOBILIZER LED stops flashing. The system
is now DISARMED.*
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The STATUS MONITOR’SLED stops flashing. The system
is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The STATUS MONITOR’SLED stops flashing. The system
is now DISARMED.*
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer
sounds for 2 seconds when the system is DISARMED, the
TRIGGER MEMORY was activated; an ALARM was TRIGGERED while
you were away from the vehicle.
* Please note, if the system utilizes your vehicle’s engine immobilizer system LED instead of the
STATUS MONITOR, the LED will continue to flash.
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO
DISARM THE SYSTEM
THE DRIVER’SDOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE
DISARMED
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-
RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM
IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS
REMOTE DISARMED
123
123
123
123
123
123
123
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
123
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 PLUS is programmed to PASSIVELY ARM, the system will ARM after the igni-
tion key is removed and all doors and the trunk or hatch are closed; you do not need to lock the
doors. When you come back to your vehicle and open a door, you must insert the key into the
ignition switch and turn it to “ON” during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will
be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no
ENTRY DELAY. See the PROGRAMMING section on page 15 to activate the PASSIVE ARMING mode,
as well as select the ENTRY DELAY time.
To PASSIVELY ARM the system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (The system will not ARM
while any of the doors are open.)
After the last door is closed:
The STATUS MONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
To DISARM the PASSIVELY ARMED system:
Enter the vehicle through a front door.
The ENTRY DELAY begins:
The STATUS MONITOR’SLED turns on (no flashing.)
Insert the key into the ignition switch and turn it to
“ON” before the
ENTRY DELAY ends.*
The LED turns off. The system is now DISARMED.
You may also DISARM the system following any of the methods
described on page 7.
NOTE: If your vehicle’s tail and marker lights turn on and the
buzzer sounds for 2 seconds when the system is
DISARMED, the TRIGGER MEMORY was activated; an ALARM
was TRIGGERED while you were away from the vehicle.
* If the ENTRY DELAY time elapses before the ignition switch is turned to “ON”, an ALARM will be
TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to “ON”, or
press and release the remote control’s UNLOCK button.
THE SYSTEM ARMS 30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR, TRUNK OR HATCH)
IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN
IT TO “ON”
123
123
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
123

Page 8 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 5
OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The STATUS MONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.
Close the trunk or hatch, if necessary.
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The STATUS MONITOR’SLED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
THE BUZZER CHIRPS ONCE WHEN
THE SYSTEM IS REMOTE ARMED
123
123
123
123
123
123
123
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
123
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 PLUS is DISARMED at the same
time. However, if you do not open a door or the trunk or hatch within 30 seconds, the system will
relock the doors and the RS3200 PLUS will REARM 30 seconds later
0
15
30
45
THE DOORS ARE
UNLOCKED BY PRESSING
THE UNLOCK BUTTON ON
THE REMOTE CONTROL...
WHEN NO DOOR, TRUNK
OR HATCH IS OPENED...
FOR MORE THAN 30
SECONDS...
THE RS3200 PLUS
AUTOMATICALLY RELOCKS
THE DOORS, THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP
FOR 30 SECONDS
(PRE-ARM), THEN
FLASHES WHEN THE
SYSTEM IS ARMED

Page 4 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 9
FEATURES FUNCTIONS
When an ALARM is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (DISARMED).
During an ALARM, the system will lock the doors if one is unlocked,
and will continue to do so for the duration of the ALARM.
The user is notified that an ALARM occurred. Upon DISARMING the
system after an ALARM was TRIGGERED, the vehicle’s tail and marker
lights will be turned on, and the BUZZER sounds, for 2 seconds.
The RS3200 PLUS flashes the vehicle’s tail and marker lights during
REMOTE ARMING and REMOTE DISARMING,as well as during an ALARM.
Also, the headlights flash during an ALARM.
During an ALARM,the RS3200 PLUS activates the vehicle’s horn.
If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM
is TRIGGERED once power is restored.
This panel houses the flashing LED that indicates the operating status
of the security system. (In vehicles with an engine immobilizer system,
that system’s LED and a separate microphone are used instead.)
STARTER DISABLE
FORCED LOCK
DURING ALARM
TRIGGER MEMORY
EXTERIOR LIGHT
ACTIVATION
HORN ACTIVATION
POWER LOSS
MEMORY
STATUS MONITOR
BRIEF DESCRIPTION–RS3200 PLUS FEATURES ALARM INFORMATION
ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
Forcibly opening a door without a key
Manually unlocking a door
Manually operating an inside lock button will TRIGGER an ALARM.
Note: Because this action will TRIGGER an ALARM, it is important
that you do not ARM the system while someone is in the
vehicle.
“Hot wiring” the vehicle
The RS3200 PLUS can detect the absence of the ignition key if the
ignition circuit is shorted in attempt to start the vehicle.
Intrusion Detection
When the radar sensor detects intrusion, it TRIGGERS a WARN AWAY
ALARM first, then a regular ALARM. See the description of how the
RADAR SENSOR TRIGGERS ALARMS on page 11.
Power restoration
If power to the system is interrupted while it is ARMED, an ALARM will
be TRIGGERED immediately when power is restored.
123
123
123
123
123

Page 10 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 3
FEATURES FUNCTIONS
The RS3200 PLUS will ARM 30 seconds after the LOCK button on the
remote control is pressed, and DISARM when the UNLOCK button is
pressed. If your vehicle is equipped with a buzzer that chirps when
the lock and unlock buttons on the remote controls are pressed, the
buzzer will also chirp when the system is REMOTE ARMED and
DISARMED.
The RS3200 PLUS will automatically RELOCK the vehicle’s doors if no
door is opened within 30 seconds after REMOTE DISARMING, then will
REARM 30 seconds later.
The RS3200 PLUS will ARM 30 seconds after you close the trunk (if
open) and lock the vehicle’s doors with the key, and will DISARM when
you unlock a door with the key.
The RS3200 PLUS may be programmed to automatically ARM 30
seconds after the ignition key is removed, the vehicle exited and the
last doorand the trunk closed, without the necessity of locking the
doors.
The RS3200 PLUS may be DISARMED with the vehicle’s ignition key
after it was PASSIVELY ARMED.
When the RS3200 PLUS has been PASSIVELY ARMED, an ENTRY
D
ELAY (user-selectable at 0, 15, or 30 seconds) will start when a door
is opened before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a
door is open), the RS3200 PLUS will ARM 30 seconds after you close
all the doors and the trunk (if open).
The RS3200 PLUS may be DISARMED by inserting the key into the
ignition switch and turning it to “ON.”
Forcibly unlocking or opening a door, hatch or trunk while the
RS3200 PLUS is ARMED will TRIGGER an ALARM immediately. (If the
system was PASSIVELY ARMED,the ENTRY DELAY must pass before the
ALARM is TRIGGERED.)
The RS3200 PLUS utilizes RADAR SENSOR to sense the intrusion
from outside, and TRIGGER an ALARM . It is fine tuned to detect
unauthorized movement inside the vehicle.
When RADAR SENSOR detects the intrusion, it TRIGGERS a WARN
A
WAY ALARM; the headlights and tail and marker lights flash, and the
horn sounds for 20 seconds, but the starter is not disabled. If there is
another detection of a door is opened or unlocked without a key, the
regular ALARM is TRIGGERED.
While ARMED, the RS3200 PLUS monitors the ignition switch. If an
attempt is made to start the vehicle without a key, an ALARM is trig-
gered.
REMOTE
ARMING/DISARMING
AUTOMATIC
REARMING
KEY
ARMING/DISARMING
PASSIVE (AUTOMATIC)
ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
RADAR SENSOR
WARN AWAY ALARM
IGNITION SWITCH
MONITORING
BRIEF DESCRIPTION–RS3200 PLUS FEATURES
ALARM INFORMATION
ALARM DESCRIPTIONS
Regular ALARM
When an ALARM is triggered in any way other than initial detection by the RADAR SENSOR,
the following occur:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The starter is disabled (no engine start) until the system is DISARMED.
The door lock will be relocked if someone reaches in and unlocks the inside lock button.
After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.
WARN-AWAYALARM
Upon initial detection of noise when sensor detects intrusion.
The horn sounds repeatedly for 20 seconds.
The headlights flash repeatedly for 20 seconds.
The tail and marker lights flash repeatedly for 20 seconds.
The interior lights turn on for 20 seconds.
If the RADAR SENSOR detects noise again within one minute, or if a door or trunk or hatch is opened
while the system is still ARMED, the regular ALARM (described above) is activated.
STOPPING AN ALARM
Simply DISARM the system using the remote control or key as described on page 6.
THE HORN SOUNDS
FOR 20 SECONDS
HEADLIGHTS FLASH
FOR 20 SECONDS
MARKER LIGHTS FLASH
FOR 20 SECONDS
TAIL LIGHTS FLASH
FOR 20 SECONDS
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH
FOR 60 SECONDS
THE STARTER IS DISABLED
UNTIL THE SYSTEM IS DIS-
ARMED
MARKER LIGHTS FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 20 SECONDS
123
123
123
123

INTRODUCTION
Congratulations on your choice of the RS3200 PLUS security system to protect your vehicle! To
get the most from the system, we strongly recommend that you read this Owner’s Guide complete-
ly to learn all of its features and functions.
The RS3200 PLUS provides comprehensive security protection through point-of-entry monitoring,
intrusion detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and
sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when someone
intrudes into the vehicle. This system is a vehicle theft deterrent and will not prevent theft of
personal goods in vehicle. For additional security, it is recommended that the vehicle top
be in the closed position. During the ALARM, the vehicle’s horn will sound and the headlights,
tail lights and front marker lights will flash. A ls o, the vehicle’s starter is disabled, to prevent engine
start.
An important note about your system
Throughout this guide, there are references to the STATUS MONITOR for this system. This panel
holds the LED indicator (for the system’s operating status). In vehicles with an engine immobilizer,
there is already a LED installed in the vehicle. If your vehicle falls into this category, remember
to look at that LED when the information refers to the STATUS MONITOR. If you do not know where
the LED is located, refer to your vehicle’s owner’s guide for specific information.
* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will
elapse when a door is opened before an ALARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
Page 2 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 11
123
123
RADAR SENSOR INFORMATION
RADAR SENSOR CHECK PROCEDURE
1. ARM the system.
Press the LOCK button on the remote control or lock the doors
with the key.
(Remember, the system will not ARM if any door is open.)
2. Wait until the STATUS MONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or hatch
is closed.
3. Move inside the vehicle.
When movement occurs inside the vehicle, A WARN AWAY ALARM
activates for 20 seconds. If sensor detects 2nd movement within 60
seconds after the 1st warn away alarm trigger, then a regular ALARM
activates for 60 seconds.
Note: If you find that the system does not perform as expected,
contact your Toyota dealer for more information.
4. DISARM the system to stop the WARN AWAYALARM.
Press the UNLOCK button on the remote control or use the key to
DISARM the system.
RADAR SENSOR OFF MODE
THE RADAR SENSOR CAN BEDEACTIVATED. PERFORM THE
FOLLOWING: PUSH THE SENSOR OFF SWITCH ON THE INSTRUMENT PANEL
BEFORE ARMING BY KEY OR REMOTE CONTROL.
IMMOBILIZER LED STARTS BLINKING.
ARM THE SYSTEM WITH THE REMOTE CONTROL OR KEY WHILE THE
IMMOBILIZER LED IS BLINKING.
THE RADAR SENSOR WILL DEACTIVATE DURING ARMING.
NOTE: IFYOU DISARM THE SYSTEM AFTER YOU SET THE RADARSENSOR
OFF, YOU HAVETO REPEAT THE ABOVE PROCEDURE WHEN YOU ARM THE
SYSTEM IF YOU WANT TO DEACTIVATE THE RADAR SENSOR AGAIN. THE
SYSTEM WILL AUTOMATICALLY CANCEL THE RADAR SENSOR OFF MODE
WHEN DISARMED.
OFF

Page 12 TOYOTA RS3200 PLUS Security system
To better understand the features and functions of this security system, please read this
Owner’s Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTION PAGE
INTRODUCTION 2
BRIEF DESCRIPTION–RS3200 PLUS FEATURES 3, 4
OPERATION
ARMING THE RS3200 PLUS (except PASSIVE ARMING) 5
DISARMING THE RS3200 PLUS(except PASSIVE DISARMING) 6
PASSIVE (AUTOMATIC) ARMING & DISARMING 7
AUTOMATIC REARMING 8
ALARM INFORMATION
ALARM TRIGGERS 9
ALARM DESCRIPTIONS 10
STOPPING AN ALARM 10
RADAR SENSOR INFORMATION 11
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 12
WARNING AND CAUTION INFORMATION 13
TOYOTA RS3200 PLUS Security system Page 1
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 PLUS is factory-set to not PASSIVELY ARM. To change the system’s operation for
PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For
more information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
a. Using the remote control,
lock, then unlock the
doors 3 times.
b. Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = PASSIVE ARMING OFF
3 times = PASSIVE ARMING ON,
0 Sec. ENTRY DELAY
4 times = PASSIVE ARMING ON,
15 Sec. ENTRY DELAY
5 times = PASSIVE ARMING ON,
30 Sec. ENTRY DELAY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the
door in 2 seconds; if this
does not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is
now complete.
e. Unlock the driver’s door
inside lock button.

TOYOTA RS3200 PLUS Security system Page 13
Warning
•This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do
not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result.
•To prevent accidents from occurring, keep the remote controls’ batteries out of the reach of chil-
dren. In the event a battery is swallowed, consult a physician immediately.
•Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric
shock may result.
•When replacing fuses, be sure to use fuses with the same specified capacity (amperage.)
Otherwise, damage to the unit or vehicle, fire or electric shock may result.
•If an abnormal condition occurs, such as liquids spilling onto the product, or the product
emitting smoke or strange odors, stop using it immediately and consult the dealer from whom
you purchased the product. Continued use of the product before corrective actions are taken
may result in an accident, injury or fire.
•Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation
may occur.
Caution
•Do not use batteries other than the type specified.
•When placing batteries into the product, insert them as shown, paying close attention to the
polarities (+ and -). If inserted improperly, the battery may explode, or leak electrolyte and
contaminate the surrounding area.
•Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock
or injury may result.
•Do not allow children to play with the remote controls. Otherwise, the doors may be locked or
unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.
•If this product is dropped or its case is damaged, disconnect the power supply lead and
contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric
shock may result.

R emote K eyless
Security system
Designed Specifically for y our Vehicle
owner’s guide
RS3200
090002-25200700
Rev. A 6/07/02
FOR MR2-SPYDER
PLUS