Traceable 08610-25 User manual

OPERATION
The Traceable Clock©contains a pre-tuned internal radio
receiver that receives a 60 kHz frequency signal generated
by the U.S.Atomic Clock. The U.S.Atomic Clock is located
in Boulder Colorado and is operated by NIST (National
Institute of Standards and Technology).
Upon installing batteries, unit automatically activates its
receiver. Upon successful reception of signal from the US
Atomic Clock, it then attempts to receive the signal every
four (4) hours and make any necessary changes to the
display.
Unit might not receive a signal immediately. It may take as
long as 72 hours to receive a complete signal from the US
Atomic Clock. While the unit is attempting to receive a com-
SOHWHVLJQDOIRUWKH¿UVWWLPHWKHFORFNPD\EHVHWPDQXDOO\
(see “Manual Clock Setting” section). Best reception often
occurs between midnight and 4 a.m.
Successful reception of theAtomic Clock signal is depen-
GHQWXSRQSRVLWLRQLQJDQGORFDWLRQRIWKHXQLW,QVXI¿FLHQW
signal strength or external electrical interference may
prevent unit from receiving a complete signal. Main causes
for poor reception are heavily reinforced concrete and
steel structures and/or placement of unit close to video
or PC monitors. Certain areas of Eastern United States
may experience urban interference from United Kingdom’s
Atomic Clock that distort or interfere with the signal from
U.S.Atomic Clock.
GETTING STARTED
1. Remove the battery door.
2. Insert two newAAsize battery according to the polarity
information marked on the battery compartment, press
the “RESET” key by using a metal wire to reset the clock.
3. Replace the battery door.
4. Once the battery is inserted, all the segments of LCD
will be shown before entering the radio controlled time
reception mode.
5. The RC clock will automatically start scanning for the
radio controlled time signal in 8 seconds.
Note: Solar panel on unit can absorb light to power clock,
but the solar power provided is limited and batteries should
EHLQVHUWHG¿UVW7KHVRODUSDQHOFDQUHGXFHWKHSRZHU
consumption of batteries and may prolong battery life.
Due to the atmospheric disturbance, the best reception
often occurs during nighttime.
QUICK REFERENCE
SNOOZE/LIGHT Press it to turn on the backlight for 5
seconds. Press to stop the current alarm
when sounding.
TIME SET Press and hold for 2 seconds to enter
time setting mode. In setting mode, press
to step the setting items. In setting mode,
press and hold for 2 seconds to save
and exit setting mode.
ADJUST In setting mode, press to change the
setting values.
ALARM ON/OFF Press to turn on/off the alarm and
snooze. Press and hold for 2 seconds to
enter alarm time setting mode. In setting
mode, press to step the setting items. In
setting mode, press to save and exit the
setting mode.
RECEIVE Press to switch between °C/°F. Press
and hold for 3 seconds to receive the RC
signal for reception testing.
RECEIVE Press to return all values to default
values. In case of malfunction, the unit
may be required to reset.
PRODUCT DESCRIPTIONS
1. LCD display
2. Solar panel
3. TIME SET key
4. ADJUST key
5. SNOOZE/LIGHT key
6. ALARM ON/OFF key
7. RECEIVE key
8. RESET key
9. Battery compartment
DISPLAY SYMBOLS
NORMAL TIME MODE
1. Time
2. Month & Date
3. Time zone map
4. Daylight saving time
5. Signal strength indicator
6. Humidity
7. Day of the week
8. Temperature
DAYLIGHT SAVING TIME (DST)
The clock has been programmed to automatically switch
when daylight saving time is in effect. Your clock will show
“DST” during the summer.
SETTING THE TIME ZONE
1. In the Normal Time Display, press and hold the TIME
SET key for 2 seconds to enter the time setting mode.
2. Press theADJUST key to set the desired time zone.
5HIHUWRWKH7LPH=RQHPDSRQWKHGLVSOD\3 3DFL¿F
M=Mountain, C=Central, and E=Eastern.
3. Press the TIME SET for 2 seconds to return to normal
time mode.
1
2
5
3
4
6
7
8
9
1
2
3
4
5
6
78
SIGNAL STRENGTH INDICATOR
The signal indicator displays signal strength in 4 levels. The
ZDYHVHJPHQWÀDVKLQJPHDQVWLPHVLJQDOVDUHEHLQJUH-
FHLYHG7KHVLJQDOTXDOLW\FRXOGEHFODVVL¿HGLQWRIRXUW\SHV
If the RC clock receives signal successfully, a sync-time
symbol “ ” will appear on the LCD. The unit has already
synchronized with the time signal transmitter. Otherwise the
antenna segment will disappear from the LCD.
NOTE: You may use the “RECEIVE” key to receive the time
signal manually. Be caution of using the RECEPTION mode,
which will consume more battery power and thus may
reduce the battery lifetime. The RECEPTION mode will be
off automatically in 6-12 minutes.
TIME AND CALENDAR SETTING
If out of reach of Radio Controlled transmitter or if reception
is not reachable, the time and calendar can be set manually.
As soon as the signal of transmitter is received again, the
clock will automatically synchronize with the exact time and
calendar.
1. In normal time mode, press and hold the “TIME SET” key
IRUVHFRQGVXQWLOWKH<HDUGLJLWÀDVKHV
2. Press the “ADJUST” key to change its value.
3. Repeat the above operations to set time and calendar in
WKLVRUGHU$!&!'!(!)!*!+!,!-'&)06)$!%
!&!'!(!)!*!+!,!-::9%
4. Press the “TIME SET” key to save and exit the setting
mode, or let it exit automatically 30 seconds later without
pressing any key.
ALARM TIME SETTING
1. Press and hold the “ALARM ON/OFF” key for 2 seconds
XQWLOWKH+RXUGLJLWÀDVKHV
2. Press the “ADJUST” key to change its value.
Normal Time Display Year Setting
Month Setting
Date Setting
12/24 Hour SettingMinute Setting
Second Setting
A
Time Zone Setting
BC
D
E
F
Hour Setting
G
H
I
Language Setting
J
3. Repeat the above operations to set the alarm Minute.
4. Press the “ALARM ON/OFF” key to save and exit the
setting mode, or let it exit automatically 30 seconds later
without pressing any key.
NOTE: The alarm will be turned on automatically when you
set the alarm time.
USING THE ALARMAND SNOOZE FUNCTION
1. Set the alarm time as described in the previous section.
2. Press the “ALARM ON/OFF” key once to turn on the
alarm until the bell icon “ ” appears.
3. Press it twice to turn on the snooze until the icon “Zz”
appears.
4. Press it again to turn off the alarm and snooze until both
icons disappear.
NOTE:
1. If alarm and snooze are turned on, press the “SNOOZE/
LIGHT” key to stop current alarm and enter snooze
mode.
2. Press “ALARM ON/OFF” key to turn off alarm and
snooze function.
3. Once Snooze function is turned on, the alarm will sound
4 times in 4-minute interval. The alarm duration is 60
seconds.
SUGGESTION
)RUWKHEHVWUHFHSWLRQ
1. It is strongly recommended to start clock at night and let
clock receive signal automatically during midnight.
2. Always place unit away from interfering sources such as
TV set, computer, etc.
3. Avoid placing unit on or next to metal plates.
4. Closed area such as airport, basement, tower block or
factory is not recommended.
5. Do not start reception in moving articles such as vehicles
or trains.
ALL OPERATIONAL DIFFICULTIES
If this Traceable Clock does not function properly for any
reason, please reset the unit. To reset the unit, depress the
RESET button located in the battery compartment. If the unit
still does not function properly, please replace the batteries
with new high quality batteries (see “Battery Replacement”
section). Low battery power can occasionally cause any
QXPEHURI³DSSDUHQW´RSHUDWLRQDOGLI¿FXOWLHV5HSODFLQJWKH
EDWWHULHVZLWKQHZIUHVKEDWWHULHVZLOOVROYHPRVWGLI¿FXOWLHV
BATTERY REPLACEMENT
Erratic readings, a faint display, no display are indicators
that the batteries must be replaced. Open the battery cover
as indicated in the illustration. Remove the exhausted
batteries and install newAAAlkaline batteries. Close the
battery cover.
Alarm Time Hour Setting Minute Setting
No signal quality Weak signal quality
Acceptable signal quality Excellent signal quality
www.calcert.com [e-mail]1.800.544.2843 0
5
10
15
20
25
30

©2017 92-5003-40 Rev. 0 102417
TRACEABLE
ATOMIC CLOCK
INSTRUCTIONS
®
www.calcert.com [e-mail]1.800.544.2843 0
5
10
15
20
25
30