Tradecraft Specialties DUMPTR-3 User manual

Model DUMPTR-3 Dump Truck Bed Revised 1/17/2015 1 of 5
Model DUMPTR-3
Read all i structio s before assembly a d use.
Keep i structio s for future use.
ADULT ASSEMBLY REQUIRED
Due to the prese ce of small parts duri g assembly, keep out of
reach of childre u til assembly is complete.
1900 Alfa Drive
La caster, PA 17601
[phone]
[email protected]
www.tradecraftspecialties.com
Instruction Manual
Bed For Full Mattress

Model DUMPTR-3 Dump Truck Bed Revised 1/17/2015 2 of 5
Use and Warnings
Your child’s safety is our top priority. Please observe the followi g safety war i gs to e sure
the safe use of this product:
● Mattress size: This bed is i te ded for use o ly with a sta dard full mattress 74” - 75”
lo g by 52 1/2” - 53 1/2” wide (mattress ot i cluded). Use of a i correctly sized
mattress may leave space betwee the edge of the mattress a d the edge of the bed.
Excess space may result i e trapme t which may lead to serious i jury or death.
● Weight limitatio : mi imum weight requireme t for this bed is 50 lbs. This product is ot
to be used by a y occupa t u der 50 lbs. Do ot let a y child u der 50 lbs. play or sleep
o or arou d the bed. Maximum weight is 350 lbs.
● Do ot sta d or sit o shelf.
● Do ot sta d, sit, or otherwise occupy or apply weight to bed slats u til a mattress or box
spri g has bee i stalled. The slats are ot rated or tested for i dividual loads without the
applicatio of mattress or box spri g.
● Do ot allow jumpi g or horseplay o the bed.
● Do ot use bed if a y parts are missi g or damaged.
● Do ot use substitute parts. Co tact ma ufacturer should replaceme t parts be
ecessary.
● Do ot use a water or sleep flotatio mattress.
● Before assembly a d use, i spect bed for damaged hardware, loose joi ts, missi g
pieces or sharp edges.
●
War i g: hardware i cluded with this product may have sharp poi ts or edges. Assembly
by a adult is required. Keep all loose hardware out of reach of childre .
● War i g: small parts are a choki g hazard for childre . Make sure that all hardware is
properly a d tightly i stalled to preve t access to loose parts by childre . Properly discard
excess hardware after assembly to preve t access of loose parts to childre . Properly
discard all packi g materials.
● Always make sure the mattress is firmly seated agai st the headboard. Excess space
may result i e trapme t which may lead to serious i jury or death.
Important Information
Each o e of our beds is ha dmade, ha d pai ted, a d ha d packaged. Mi or imperfectio s
may occur that are ot ma ufacturi g defects, but rather a result of the ha dcrafti g process
that makes our beds u ique a d special.
General Specifications
Assembled dime sio s (approximate): 89" lo g, 54.5" wide, 24" high
Disassembly
To disassemble, reverse order of steps for assembly.

Model DUMPTR-3 Dump Truck Bed Revised 1/17/2015 3 of 5
Care and Maintenance
● Check all faste ers periodically for tight ess.
● Clea the surface usi g a slightly damp cloth if ecessary. Do ot use a y corrosive
clea i g products or abrasives that may degrade or damage the surface. Fur iture polish
may be used to clea dust off the surface.
● We recomme d that a y clea i g materials first be tested o a surface that would ot be
visible duri g the course of ormal use.
● Lift slightly whe movi g o carpet or rough surface to avoid be di g or damagi g the
supporti g structure of the bed.
● Use of a vaporizer close to bed may cause the surface to swell a d the surface to peel.
● Check the mattress periodically a d whe cha gi g sheets to e sure mattress is tight
agai st headboard.
Assembly
Hardware notes: do ot fully tighte a y faste ers u til all hardware is i place. Failure to
follow these i structio s may cause faste ers to misalig duri g assembly. If usi g power tools
to aid i assembly, use cautio . Power tools may over-tighte faste ers a d split or damage
the material.
ools required (not included):
Phillips head screw driver
7/16” wre ch or adjustable wre ch
Parts List:
Part #: Quantity: Description: Reference image only (not to scale):
[A] (2) Side assembly
[B] (11) Mattress support bar
[C] (1) Shelf fro t sectio
[D] (1) Shelf rear sectio
[E] (1) Shelf [shelf is flat, thi sheet]
[F] (6) ¼” Lag bolt
[G] (6) ¼” Metal flat washer
[H] (40) Screw

Model DUMPTR-3 Dump Truck Bed Revised 1/17/2015 4 of 5
Assembly (continued)
Step 1: E sure there is e ough room to lay out all parts. Carefully u pack all parts a d hard-
ware a d check that everythi g is prese t a d u damaged. It is helpful to have more tha
o e perso available for assembly.
Step 2: Loosely faste side assemblies [A] to shelf rear [D] a d shelf fro t [C] usi g lag bolts
[F] a d flat washers [G], (3) lag bolts per side with a washer o each lag bolt. Do not yet
fully tighten lag bolts.
Step 3: Faste shelf [E] to shelf fro t sectio [C] a d shelf rear sectio [D] usi g (18) screws
[H].

Model DUMPTR-3 Dump Truck Bed Revised 1/17/2015 5 of 5
Assembly (continued)
Step 4: Faste mattress support bars [B] to mattress support rail of side assemblies [A] usi g
screws [H]. Use (1) screw at each e d of support bar. Make sure support bar e d is tight with
side of bed. Start at rear of bed a d work towards fro t. Leave 4.5” gaps betwee each sup-
port bar.
Step 5: Tighte all hardware. Make sure all assembled parts are tight a d secure.