Tradecraft Specialties GASHLF-7 User manual

Bed Frame Accessory
Model GASHLF-7
Model GASHLF-7 Bed Frame Accessory Revised 11/18/2016 Page 1 of 5
Read all instructions before assembly and use.
Keep instructions for future use.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep
out of reach of children until assembly is complete.
1900 Alfa Drive
Lancaster, PA 17601
[phone]
[e-mail]
www.tradecraftspecialties.com
Instruction Manual

Use and Warnings
Your child’s safety is our top priority. Please observe the following safety warnings to ensure the safe
use of this product:
● STRANGULATION HAZARD - Never attach or hang items to any part of this product that are not
designed for use with the product; for example, but not limited to, hooks, belts and jump ropes.
● Do not allow jumping or horseplay around or near this product.
● Do not use product if any parts are missing or damaged.
● Do not use substitute parts. Contact manufacturer should replacement parts be necessary.
● Before assembly and use, inspect product for damaged hardware, loose joints, missing pieces
or sharp edges.
● Warning: hardware included with this product may have sharp points or edges. Assembly by an
adult is required. Keep all loose hardware out of reach of children.
● Warning: small parts are a choking hazard for children. Make sure that all hardware is properly
and tightly installed to prevent access to loose parts by children. Properly discard excess
hardware after assembly to prevent access of loose parts to children. Properly discard all
packing materials.
General Specifications
Assembled dimensions (approximate): 24" long, 50.5" (on full) or 35.5" (on twin) wide, 13" high.
Important Information
Each one of our products is handmade, hand painted, and hand packaged. Minor imperfections may
occur that are not manufacturing defects, but rather a result of the handcrafting process that makes
our products unique and special.
Care and Maintenance
● Check all fasteners periodically for tightness.
● Clean solid surfaces using a slightly damp cloth if necessary. Do not use any corrosive cleaning
products or abrasives that may degrade or damage the surface. Furniture polish may be used to
clean dust off solid surfaces.
● We recommend that any cleaning materials first be tested on a surface that would not be visible
during the course of normal use.
● Use of a vaporizer close to this product may cause the surface to swell and the surface to peel.
Model GASHLF-7 Bed Frame Accessory Revised 11/18/2016 Page 2 of 5

Disassembly
To disassemble, reverse order of steps for assembly.
Assembly Notes
Hardware notes: do not fully tighten any fasteners until all hardware is in place. Failure to follow
these instructions may cause fasteners to misalign during assembly. If using power tools to aid in
assembly, use caution. Power tools may over-tighten fasteners and split or damage the material.
Tools required (not included):
Phillips head screw driver
7/16” wrench or adjustable wrench
Model GASHLF-7 Bed Frame Accessory Revised 11/18/2016 Page 3 of 5

Parts List
Model GASHLF-7 Bed Frame Accessory Revised 11/18/2016 Page 4 of 5

Assembly Steps
Step 1: Ensure there is enough room to lay out all parts. Carefully unpack all parts and hardware
and check that everything is present and undamaged. It is helpful to have more than one person
available for assembly.
Step 3: Tighten all hardware. Make sure all assembled parts are tight and secure.
Model GASHLF-7 Bed Frame Accessory Revised 11/18/2016 Page 5 of 5
Step 2:
--Fasten shelves [D] to side panels [E] with lag screws [A] using (1) washer [B] on each lag screw.
--Fasten back [F] to unit using wood screws [C] through pre-drilled holes.