Better Homes and Gardens BH47-021-399-03 User manual

PB 1
model# BH47-021-399-03
model# BH47-021-399-04
model# BH47-021-399-05
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
gray
ivory
black
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
LAUREL COFFEE TABLE

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
UPPER RAIL
LOWER RAIL
PARTITION
FIXED SHELF
SHELF RAIL
BACK PANEL
DRAWER FRONT [X2]
LEFT DRAWER SIDE [X2]
RIGHT DRAWER SIDE [X2]
DRAWER BACK [X2]
DRAWER BOTTOM [X2]
DRAWER SUPPORT [X2]
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Knob
x4
3. Cam
x28
4. Cam Cover
x4
1. Wood Dowel
x38
2. Cam Bolt
x28
6. Knob Bolt
x4
7. Flat Head Screw
x17

4
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

4 5
x2 x2
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6
x2 x2 x2
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x4 x8 x8
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x2 x3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 4
1. Wood
Dowel
7. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8 9
x4 x4
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 5
1. Wood
Dowel
7. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x10 x10 x10
STEP 6
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
x12 x6 x6 x4
x2
x2
STEP 7
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
4. Cam Cover

12
x10x4 x4x4
x2
x2
STEP 8
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
1. Wood
Dowel
5. Knob 7. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
6. Knob Bolt

12 13
STEP 9

14
80 lbs. / 36.3 kg.
15 lbs. per drawer /
6.8 kg. por cajón
80 lbs. / 36.3 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.

PB 1
model# BH47-021-399-03
model# BH47-021-399-04
model# BH47-021-399-05
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
gris
marl
negro
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
MESA PARA CAFÉ LAUREL
Instrucciones de Ensamble

2
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
RIEL SUPERIOR
RIEL INFERIOR
DIVISOR
REPISA FIJA
RIEL REPISA
PANEL POSTERIOR
CAJÓN FRONTAL [X2]
CAJÓN IZQUIERDO [X2]
CAJÓN DERECHO [X2]
CAJÓN POSTERIOR [X2]
CAJÓN INFERIOR [X2]
SOPORTE DE CAJÓN [X2]
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Martillo Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Perilla
x4
3. Leva
x28
4. Cubierta del Tornillo
x4
6. Perno de Perilla
x4
2. Tornillo de Leva
x28
1. Clavija de Madera
x38
7. Tornillo de Cabeza
Plana
x17

4
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

4 5
x2 x2
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6
x2 x2 x2
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.