Tradecraft Specialties SEMITR-2 User manual

Model SEMITR-2 Tractor/Trailer Bed Revised 1/18/2015 1 of 4
Model SEMITR-2
Read all instructions before asse bly and use.
Keep instructions for future use.
ADULT ASSEMBLY REQUIRED
Due to the presence of s all parts during asse bly, keep out of
reach of children until asse bly is co plete.
1900 Alfa Drive
Lancaster, PA 17601
[phone]
tradecraftspecialties@g ail.co
www.tradecraftspecialties.co
Instruction Manual
Bed For Twin Mattress

Model SEMITR-2 Tractor/Trailer Bed Revised 1/18/2015 2 of 4
Important Information
Each one of our beds is hand ade, hand painted, and hand packaged. Minor i perfections
ay occur that are not anufacturing defects, but rather a result of the handcrafting process
that akes our beds unique and special.
Disassembly
To disasse ble, reverse order of steps for asse bly.
Use and Warnings
Your child’s safety is our top priority. Please observe the following safety warnings to ensure
the safe use of this product:
● Mattress size: This bed is intended for use only with a standard twin attress 74” - 75”
long by 37 1/2” - 38 1/2” wide ( attress not included). Use of an incorrectly sized
attress ay leave space between the edge of the attress and the edge of the bed.
Excess space ay result in entrap ent which ay lead to serious injury or death.
● Weight li itation: ini u weight require ent for this bed is 50 lbs. This product is not
to be used by any occupant under 50 lbs. Do not let any child under 50 lbs. play or sleep
on or around the bed. Maxi u weight is 350 lbs.
● Do not stand or sit on shelf.
● Do not stand, sit, or otherwise occupy or apply weight to bed slats until a attress or box
spring has been installed. The slats are not rated or tested for individual loads without the
application of attress or box spring.
● Do not allow ju ping or horseplay on the bed.
● Do not use bed if any parts are issing or da aged.
● Do not use substitute parts. Contact anufacturer should replace ent parts be
necessary.
● Do not use a water or sleep flotation attress.
● Before asse bly and use, inspect bed for da aged hardware, loose joints, issing
pieces or sharp edges.
●
Warning: hardware included with this product ay have sharp points or edges. Asse bly
by an adult is required. Keep all loose hardware out of reach of children.
● Warning: s all parts are a choking hazard for children. Make sure that all hardware is
properly and tightly installed to prevent access to loose parts by children. Properly discard
excess hardware after asse bly to prevent access of loose parts to children. Properly
discard all packing aterials.
● Always ake sure the attress is fir ly seated against the headboard. Excess space
ay result in entrap ent which ay lead to serious injury or death.
General Specifications
Asse bled di ens
ions (approxi ate): 81" long, 39.5" wide, 12" high

Model SEMITR-2 Tractor/Trailer Bed Revised 1/18/2015 3 of 4
Care and Maintenance
● Check all fasteners periodically for tightness.
● Clean the surface using a slightly da p cloth if necessary. Do not use any corrosive
cleaning products or abrasives that ay degrade or da age the surface. Furniture polish
ay be used to clean dust off the surface.
● We reco end that any cleaning aterials first be tested on a surface that would not be
visible during the course of nor al use.
● Lift slightly when oving on carpet or rough surface to avoid bending or da aging the
supporting structure of the bed.
● Use of a vaporizer close to bed ay cause the surface to swell and the surface to peel.
● Check the attress periodically and when changing sheets to ensure attress is tight
against headboard.
Assembly
Hardware notes: do not fully tighten any fasteners until all hardware is in place. Failure to
follow these instructions ay cause fasteners to isalign during asse bly. If using power tools
to aid in asse bly, use caution. Power tools ay over-tighten fasteners and split or da age
the aterial.
ools required (not included):
Phillips head screw driver
7/16” wrench or adjustable wrench
Parts List:
Part #: Quantity: Description: Reference image only (not to scale):
[A] (2) Side asse bly
[B] (11) Mattress support bar
[C] (1) Shelf front section
[D] (4) ¼” Lag bolt
[E] (4) ¼” Metal flat washer
[F] (22) Screw

Model SEMITR-2 Tractor/Trailer Bed Revised 1/18/2015 4 of 4
Assembly (continued)
Step 1: Ensure there is enough roo to lay out all parts. Carefully unpack all parts and hard-
ware and check that everything is present and unda aged. It is helpful to have ore than
one person available for asse bly.
Step 2: Loosely fasten side asse blies [A] to headboard [C] using lag bolts [D] and flat
washers [E], (2) lag bolts per side with a washer on each lag bolt. Do not yet fully tighten
lag bolts.
Step 3: Fasten attress support bars [B] to attress support rail of side asse blies [A] using
screws [F]. Use (1) screw at each end of support bar. Make sure support bar end is tight with
side of bed. Start at rear of bed and work towards front. Leave 4.5” gaps between each sup-
port bar.
Step 6: Tighten all hardware. Make sure all asse bled parts are tight and secure.