TradeQuip 1192T User manual

04/20 Product Code: 1192T
Made in China to TQB Brands Pty Ltd specifications.
Visit us at www.tqbbrands.com.au
About the TradeQuip brand
The 'TradeQuip' brand of workshop equipment, is designed for use in a demanding workshop
environment by professional users. With proven and trusted “Made for the
Trade” reliability, 'TradeQuip' branded products offer the very best in performance for an
affordable price. All backed by a 1year trade guarantee across 1,000+ distributors Australia wide.
Product Code: 1192T
T
TRANSMISSION
ENGINE CRANE
LIFTER
ENGINE
STAND FOLDING
Specifications:
Safe Working Capacity: 900kg
Operating Height (A) : 800mm Floor to
mounting plate centre
Width(B) : 530mm
Length (C): 1110mm
ID between legs (D): 780mm
OD between legs (E): 930mm
Lower steel tubing: 60x60mm
Column tubing: 70x70mm
Nett Weight: 45kg
Carton: 910 x 210 x 180mm
Gross Weight: 47kg

04/20 Product Code: 1192T
Made in China to TQB Brands Pty Ltd specifications Page 2
Visit us at www.tqbbrands.com.au
WARNING
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
WARNING
The instructions and warnings contained in this manual should be read and understood before using or operating this equipment.
Do not allow anyone to use or operate this equipment until they have read this manual and have developed a thorough
understanding of how this equipment works. Failure to observe any of the instructions contained in the manual could result in
severe personal injury to the user or bystanders, or cause damage to the equipment and property. Keep this manual in a
convenient and safe place for future reference.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the TQB Brands Pty Ltd policy of
continuous improvement determines the right to make modifications without prior warning.
CONTENT
WARNING............................................................................................................................................................................................ 2
CONTENT............................................................................................................................................................................................. 2
STANDARD OPERATING PROCEDURE ................................................................................................................................................. 3
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE .................................................................................................................... 4
PARTS DIAGRAM ................................................................................................................................................................................. 5
PARTS LIST........................................................................................................................................................................................... 5
WARRANTY ......................................................................................................................................................................................... 6

04/20 Product Code: 1192T
Made in China to TQB Brands Pty Ltd specifications Page 3
Visit us at www.tqbbrands.com.au
PRE-OPERATIONAL SAFETY CHECKS
Save these instructions. For your safety, read, understand, and follow the information provided.
Before using the engine stand ensure it is in sound condition, and good working order.
Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate
the warranty.
Keep the stand clean for best and safest performance.
Locate the stand in an adequate working area for its function, keep area clean and tidy and free from unrelated materials,
and ensure there is adequate lighting.
Use on a firm, level surface capable of sustaining the engine stand and the load.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Ensure all non essential persons keep a safe distance whilst the stand is in use.
Lock mounting plate in position before fixing a load, and ensure the load is centred and securely mounted on the locking
plate.
Always ensure the Stand and the load is stable.
To move a loaded stand, push it from the load side, above the two fixed wheels. DO NOT move the stand from the castor end
and never pull the stand towards yourself. Also ensure surface over which the stand is to travel is strong enough to take the
stand load and that it is not cracked, uneven or obstructed.
DO NOT operate unit if damaged.
DO NOT allow untrained persons to operate the stand.
DO NOT exceed the rated capacity of 900kg.
DANGER: DO NOT work under an engine mounted on the stand.
Intended Use
For safe handling and positioning of most 6 and 8 cylinder passenger car engines during dismantling and re-assembly.
STANDARD OPERATING PROCEDURE
DO NOT use this machine unless you have been trained and assessed to a competent level in its sate use and operation, and
have been given permission to use this
Safety glasses must be worn when operating this
equipment
Long loose hair must be contained when operating
this equipment
Safety footwear must be worn when operating
this equipment
Close fitting/protective clothing must be worn
when operating this equipment
Rings and jewellery must not be worn when
operating this equipment

04/20 Product Code: 1192T
Made in China to TQB Brands Pty Ltd specifications Page 4
Visit us at www.tqbbrands.com.au
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE
1. FEATURES
The 1192T 900kg Engine Stand accepts a wide variety of engines and transmissions. The head swivels 360º for accessibility
to all parts of the engine. It has fully adjustable mounting arms.
Swivel castors provide excellent manoeuvrability. This model also offers a higher than average capacity and features
foldable legs for easier storage and transport.
2. ASSEMBLY
1. Bolt the three castor wheels to the main frame (4) using M8x10mm bolts (6) and lock washers (17).
2. Assemble the legs (9) to the frame using the 4 ringed pins provided (8). Lay each leg into the open channel and insert
the first pin into the hole nearest the back of the frame. This will be the folding leg pivot. Retain the pin with an ‘R’ clip
(7). Lock the leg in the down position by inserting a second pin into the hole nearest the open end of the channel and
retain it with a ‘R’ clip.
3. Bolt the main upright (2) to the cross member between the open channels using two M14 bolts (14). Fix with the nuts
(15) and washers (16) provided but leave hand tight at this stage.
4. Take the two support struts (3) and loosely bolt them to the top of the main upright using an M16 100mm bolt (13).
Insert two M16 bolts (18) through the angled parts of the main base in the holes adjacent to the rear square section
ensuring that the bolt heads are on the outside of the frame. Slide the bottom of each support strut over the end of
each bolt in turn and secure with the nuts (21) and washers provided. Tighten all bolts holding the main upright and
struts.
5. Take the engine mounting plate (11 - turning plate) and insert it thought the tube at the top of the main upright.
Rotate the plate until one of the holes in the inner tube is aligned with a hole in the outer tube and insert the ringed pin
(1).
6. Take the handle (12) and insert it through the hole in the turning plate tube which protrudes from the top of the main
upright.
7. Attach the adjustable mountings to the turning plate using 65mm M14 bolts (19) ensuring that the washer (20) is
directly under the head of the bolt.
8. To fold up the legs remove the spring clips from the ring headed pins closest to the fixed wheels and pull out the pins.
Fold the legs up. Always retain the legs in the upright position by reinserting the pins through the holes in the frame
directly in front of the folded legs. Retain pins with clips.
3. BEFORE USE
Prior to each use conduct a visual inspection by checking for abnormal conditions, such as cracked joints and damaged,
loose, or missing parts.
4. STORAGE
This Engine Stand should always be stored in a dry location on a level surface.
5. MAINTENANCE
Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will
invalidate the warranty.
Keep the stand clean for best and safest performance.
6. SERVICE & REPAIR
Any Engine Stand found damaged in any way, or found to be worn or operates abnormally should be removed from service
until repaired by an authorised service agent. Owners and / or operators should be aware that repair of this product may
require specialised equipment and knowledge. Only authorised parts, labels and decals shall be used on this equipment.
Annual inspection of the engine stand is recommended and can be made by an authorised repair facility to ensure that your
equipment is in optimum condition and that the equipment has the correct decals and safety labels specified by the
manufacturer.

04/20 Product Code: 1192T
Made in China to TQB Brands Pty Ltd specifications Page 5
Visit us at www.tqbbrands.com.au
PARTS DIAGRAM
PARTS LIST
Part
Description
Part
Description
1
Pin
12
Handle
2
Vertical Pillar
13
Bolt M16x100
3
Support
14
Bolt M14x85
4
Base Frame
15
Nut M14
5
3 ½ “ Castor
16
Spacer diameter 14mm
6
Bolt M8x10
17
Washer diameter 8mm
7
Spring Pin
18
Bolt M16x90
8
Bolt (ring headed pin)
19
Bolt M14x65
9
Legs
20
Washer diameter 16mm
10
Shifting Stand
21
Nut M16
11
Turning Plate

04/20 Product Code: 1192T
Made in China to TQB Brands Pty Ltd specifications Page 6
Visit us at www.tqbbrands.com.au
WARRANTY
Tradequip products have been carefully tested and inspected before shipment and are guaranteed to be free from defective
materials and workmanship for a period of 12 months from the date of purchase except where tools are hired out when the
guarantee period is ninety days from the date of purchase.
Should the machine develop any fault, please return the complete tool to your nearest authorised warranty repair agent or contact
TQB Brands Pty Ltd Warranty team –[e-mail].
If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free
of charge. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless or
unsafe handling, alterations, accident, or repairs attempted or made by any personnel other than the authorised TQB Brands Pty
Ltd repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised.
Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your
proof of purchase within the 12 month period.
Consumer Guarantee
Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
All images and illustrations shown are for reference purposes only. All information, specifications and illustrations in this manual are based on
the latest information available at the time of publication and are subject to change without notice. The information in this manual is periodically
revised to ensure the latest information is included. Download the latest version of this manual and other related technical documentation from
www.tqbbrands.com.au