TradeQuip 1198T User manual

Aug_19 Product Code: 1198T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
OWNER’S MANUAL
PRODUCT CODE: 1198T
680kg UNDERHOIST AUXILIARY
STAND
Model
Safe Working Capacity
Minimum Height
Maximum Height
Base Diameter
1198
680kg
1360mm
2000mm
300mm

Aug_19 Product Code: 1198T
Made in China to TQB Brands Pty Ltd Specifications Page 2
Visit us at www.tqbbrands.com.au
WARNING INFORMATION
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
WARNING
The instructions and warnings contained in this manual should be read and understood before using or operating this
equipment. Do not allow anyone to use or operate this equipment until they have read this manual and have developed a
thorough understanding of how this equipment works. Failure to observe any of the instructions contained in the manual could
result in severe personal injury to the user or bystanders, or cause damage to the equipment and property. Keep this manual in
a convenient and safe place for future reference.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the TradeQuip policy of
continuous improvement determines the right to make modifications without prior warning.
CONTENT
WARNING INFORMATION................................................................................................................................................................... 2
CONTENT............................................................................................................................................................................................. 2
SAFETY INSTRUCTIONS........................................................................................................................................................................ 2
ASSEMBLY, OPERATION & PREVENTATIVE MAINTENANCE................................................................................................................ 3
PARTS DIAGRAM & LIST ...................................................................................................................................................................... 4
WARRANTY ......................................................................................................................................................................................... 5
SAFETY INSTRUCTIONS
SAFETY OPERATING INSTRUCTIONS
Check vehicle owner's manual for correct vehicle weight - DO NOT exceed parts stands' safe working capacity.
Use only as specified by the manufacturer.
Use only on a hard, level surface.
Securely support the vehicle before placing parts stands in place.
Install and lock the ratchet bar in position as described in these instructions.
For your safety, do not modify or alter these auxiliary parts stands.
Use the right product for the job. There are certain applications for which the Jack Stands was designed. Do not modify
the Jack Stands and do not use the Jack Stands for a purpose for which it was not intended.

Aug_19 Product Code: 1198T
Made in China to TQB Brands Pty Ltd Specifications Page 3
Visit us at www.tqbbrands.com.au
ASSEMBLY, OPERATION & PREVENTATIVE MAINTENANCE
1. FEATURES
TradeQuip Auxiliary Parts Stands are intended to be used as a means of partial support and the positioning of vehicle
components during their installation/removal. The Auxiliary Parts Stand is not for use in stabilising or supporting vehicles. These
are for use under a 2 or 4 post overhead vehicle lift or in a garage pit. Heavy gauge steel construction to ensure safety, strength
and stability.
2. ASSEMBLY
Insert smaller end of threaded column through the bottom of upright, allowing small end of threaded column to project
out of the top of upright.
Place bearing over threaded portion with upright/threaded column assembly in the horizontal position.
Spin adjusting handle clockwise onto threaded portion.
Insert the roll pin through saddle & threaded column to fasten saddle.
Insert upright assembly onto base with slot in upright facing foot pedal mount.
Secure upright using the larger pin, washer and r-clip.
Insert pedal into slot and secure with remaining pin, washer, and r-clip.
3. BEFORE USE
Conduct a thorough visual inspection checking for any abnormal conditions, such as cracked welds, and damaged, loose, or
missing parts.
4. OPERATION
Prior to each use always conduct a visual inspection checking for any abnormal conditions, such as cracked welds, and
damaged, loose, or missing parts.
To Raise:
Turn adjusting handle clockwise until saddle contacts load. Be sure to centre load on saddle.
Slight upward adjustments can be made to the saddle height by pressing downward on the foot pedal.
This may or may not be necessary depending on the application. It is provided as a means of making temporary
adjustments on load height without using your hands. This leaves your hands free to engage, handle and control the
workpiece.
WARNING
The stands must be positioned on a hard level (concrete) surface.
The safe working load must not be exceeded under any circumstances.
DO NOT lower overhead lift in order to accommodate load on stand.
Contact with the desired vehicle component shall only be done by means of the vertical adjustments provided on the
stand.
Always centre the component load on the saddle.
To Lower Vehicle:
Turn adjusting handle counter clockwise
Carefully remove stand from underneath vehicle.
Slowly lower vehicle to the ground with overhead lift hoist control.
5. STORAGE
These Jack Stands should always be stored in a dry indoor location in the upright position.
6. MAINTENANCE
Periodically inspect each stand. Ensure all parts move freely. Do not apply oil or grease to any part of this product. If rust
appears, sand the affected area and cover with suitable paint. This product has no replacement parts.
7. SERVICE & REPAIR
Any Auxiliary Parts Stands found damaged in any way, or found to be worn or operates abnormally should be removed from
service until repaired by an authorised service agent. Owners and / or operators should be aware that repair of this product
may require specialised equipment and knowledge. Only authorised parts, labels, decals shall be used on this equipment.
Annual inspection of the Jack Stands is recommended and can be made by an authorised repair facility to ensure that your
equipment is in optimum condition and that the equipment has the correct decals and safety labels specified by the
manufacturer.

Aug_19 Product Code: 1198T
Made in China to TQB Brands Pty Ltd Specifications Page 4
Visit us at www.tqbbrands.com.au
PARTS DIAGRAM & LIST
Part #
Description
QTY
Part #
Description
QTY
1
Lifting Screw
1
8
Flat Washer 16
2
2
Spring 6x26
1
9
Clevis Pin with Head 16x70
1
3
Handle
1
10
Clevis Pin with Head 12x35
1
4
Handle Sleeve
2
11
Flat Washer 12
2
5
Bearing
1
12
Base
1
6
Upright Column
1
13
Foot Bar
1
7
Pedal Lever
1
14
"R" Clip
2

Aug_19 Product Code: 1198T
Made in China to TQB Brands Pty Ltd Specifications Page 5
Visit us at www.tqbbrands.com.au
WARRANTY
TradeQuip products have been carefully tested and inspected before shipment and are guaranteed to be free from defective
materials and workmanship for a period of 12 months from the date of purchase except where tools are hired out when the
guarantee period is ninety days from the date of purchase.
Should the machine develop any fault, please return the complete tool to your nearest authorised warranty repair agent or
contact TQB Brands Pty Ltd Warranty team –[e-mail].
If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out
free of charge. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless
or unsafe handling, alterations, accident, or repairs attempted or made by any personnel other than the authorised TQB Brands
Pty Ltd repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised.
Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your
proof of purchase within the 12 month period.
Consumer Guarantee
Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.