Tradinco TRAQC-5 P User manual

TRAQC-5 P & TRAQC-1
Pneumatic Hand Pump Types P40 / P60
&
Digital Manometer
User Manual

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 2
Contents
1. Warranty ............................................................................................ 4
2. About this operating manual.................................................................. 5
TRAQC-5 P40/P60 ............................................................................................ 6
3. Device description ................................................................................ 7
3.1 Scope of delivery and accessories ...................................................... 7
3.2 Accessories (optional)....................................................................... 7
3.3 Intended use ................................................................................... 8
4. Safety instructions ............................................................................... 9
4.1 Qualified personnel........................................................................... 9
4.2 General safety instructions ................................................................ 9
4.3 Special safety instructions ............................................................... 10
5. Design and function............................................................................ 11
5.1 Function........................................................................................ 11
6. Initial setup....................................................................................... 12
7. Operation.......................................................................................... 13
7.1 Creating pressure........................................................................... 14
7.2 Increasing pressure with the fine adjustment valve ............................ 15
7.3 Creating vacuum............................................................................ 16
7.4 Pressure / vacuum measurements.................................................... 17
7.5 Carrying out the pressure or vacuum measurements .......................... 17
7.6 Completing the pressure or vacuum measurements............................ 17
8. Practical / usage guidelines ................................................................. 18
8.1 Setting the spring preload / stroke limitation ..................................... 18
8.2 Pumping process............................................................................ 18
9. Problems........................................................................................... 19
10. Maintenance/cleaning, storage and transportation.................................. 20
10.1 Maintenance .................................................................................. 20
10.2 Cleaning ....................................................................................... 20
10.3 Storage and transportation.............................................................. 20
11. Disposal............................................................................................ 21
12. Technical data and accessories ............................................................ 22
TRAQC-1 DPG.................................................................................................. 23
13. Introduction TRAQC-1 DPG.................................................................. 24
13.1 Notes on safety / production selection .............................................. 24
13.2 Device versions and range of delivery ............................................... 25
14. Commissioning .................................................................................. 26
14.1 Replacing the batteries ................................................................... 26
15. Functions and keys............................................................................. 27
15.1 Display ......................................................................................... 27
15.2 Keys............................................................................................. 27
15.3 Display mode................................................................................. 28
15.4 Menu functions .............................................................................. 28
16. Connection ........................................................................................ 30
17. Operating.......................................................................................... 31
17.1 Turning on (ON)............................................................................. 31
17.2 Turn off (OFF)................................................................................ 31
17.3 Turn on backlight ........................................................................... 32
17.4 MIN/MAX indication ........................................................................ 32
17.5 FS FullScale display ........................................................................ 32
17.6 Erasing MIN/MAX values ................................................................. 32
17.7 OFL Display ................................................................................... 32
17.8 Zero point correction (ZERO) ........................................................... 33
17.9 Resetting the zero point correction ................................................... 33
17.10 Automatic power off ....................................................................... 34
17.11 Changing the unit........................................................................... 35
17.12 Filter settings ................................................................................ 36

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 3
17.13 Display serial number ..................................................................... 37
18. Technical data ................................................................................... 38

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 4
1. Warranty
During the design and manufacturing of this instrument the at most attention has been given to
quality and durability.
This manual contains information needed for the safe and effective use of the
capabilities of the instrument.
Please read the manual carefully before operating the instrument. By doing so possible
damage to the instrument or damage caused by the incorrect use of the instrument can
be avoided.
TRADINCO INSTRUMENTS warrantees the instrument in accordance with the Standard Terms and
Conditions of the Instrument Trade as issued by the Association bearing the name "Federation
Het Instrument" (The Instrument Federation, (filed with the Clerk of Utrecht District Court on 13
January 1993 under number 16/93 and with the Chamber of Commerce and Industry in
Amersfoort on 18 January 1993. A copy is available on request.
TRADINCO INSTRUMENTS warrantees that this product will be free from defects in materials and
workmanship for a period of 5 years from the date of shipment. If any such product proves
defective during this warranty period, TRADINCO INSTRUMENTS, at its option, will either repair
the defective product without charge for parts or labour, or will provide a replacement in
exchange for the defective product.
In order to obtain service under this warranty, Customer must notify TRADINCO INSTRUMENTS of
the defect before the expiration of the warranty period and make suitable arrangements for the
performance of the service.
Customer shall be responsible for packaging and shipping of the defective product to the service
centre designated by TRADINCO INSTRUMENTS, with shipping charges prepaid.
If no defect can be found Customer may be charged for costs of the investigation.
This warranty does not apply to any defect, failure or damage caused by:
a. Improper use of the instrument.
b. Normal wear of the product.
c. Modification or repair carried out by or on behalf of the owner or by a third party.
d. Implementation of modifications to the product that are not supplied or implemented by
TRADINCO INSTRUMENTS.
TRADINCO INSTRUMENTS and its vendors will not be liable for any indirect, special, incidental or
consequential damages irrespective of whether TRADINCO INSTRUMENTS or the vendor has
advance notice of the possibility of such damages.
The type number of the product, as listed on the instrument tag plate, should always be
mentioned in any correspondence concerning the product.
Tradinco Instrumenten-Apparaten b.v.
Radonstraat 250
2718 TB Zoetermeer
The Netherlands
[phone]
www.tradinco.com
[e-mail]

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 5
2. About this operating manual
The operating manual is aimed at specialists and semi-skilled personnel.
Before each step, read through the relevant advice carefully and keep to
the specified order.
Thoroughly read and understand the information in the section “Safety
instructions”.
If the term 'pressure' is used in a very general way, then both positive
pressure and negative pressure (vacuum) are intended.
If you have any problems or questions, please contact your supplier or contact
us directly:
Tradinco Instrumenten-Apparaten b.v.
Radonstraat 250
2718 TB Zoetermeer
The Netherlands
[phone]
www.tradinco.com
[e-mail]
Hazard symbols and other symbols used:
CAUTION! Crushing hazard!
This symbol indicates hazards which could result in the crushing of fingers or
hands.
CAUTION! Risk of injury in the case of excessive pressure!
This sign indicates dangers which could arise from excessive pressure in a piece
of equipment.
CAUTION! Material damage!
This symbol indicates actions which could lead to possible damage to material or
environmental damage.
ADHERE TO OPERATING MANUAL!
NOTICE!
This symbol indicates important
notices, tips or information.
Pay attention to and comply with
information that is marked with this
symbol.
Follow the specified instructions and
steps.
Adhere to the given order.
Check the specified points or notices.
Reference to another section,
document or source.
•Item
+p

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 6
TRAQC-5 P40/P60
Pneumatic Hand Pump Types P40 / P60
User Manual

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 7
3. Device description
The hand pump creates positive pressure or a
vacuum for the inspection, adjustment or
calibration of pressure devices of all kinds.
The hand pump can be used for test items
directly on location, thanks to its light weight
and compact design.
When the hand pump is used, it needs to be
connected to a reference gauge and to the
test item.
Versions:
The hand pump is available for two pressure
ranges:
Type
Pressure range
P40
-0,95 … 40 bar
P60
-0,95 … 60 bar
3.1 Scope of delivery and accessories
Check the delivered items.
Hand pump.
Pressure hose:
The pressure hose is supplied from the factory already screwed onto the hand
pump.
The pressure hose should remain attached to the hand pump during
operation, storage and transportation. Removing the pressure hose should be
avoided.
Operation manual.
3.2 Accessories (optional)
Transportation cases, adapter sets, seal sets and reference gauges can be
ordered as accessories.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 8
Transportation case (Item No.:
HP40CASE01):
The transportation case provides optimal
protection for the hand pump and other
accessories with its tight-fitting rigid foam
inlay.
A document compartment is located in the
lid behind the burl foam inlay.
Adapter set (Item No.: HP40ADAPT01):
The adapter set comprises 11 adapters for
all common pressure connections with or without pins.
Seal set (item No.: HP40SEAL01):
The seal set contains flat seals made of plastic and O-rings for all common
pressure connections.
Replacement pressure hose with seals (item No.: HP40HOSE01):
The pressure hose is available separately as a replacement part with the
necessary seals.
3.3 Intended use
The P40 and P60 hand pumps may only be used for the creation of air pressure
or air vacuum. Use with any other media, particularly hydraulic oil, will result in
damage to the hand pump.
The hand pump may not be attached to external pressure sources.
The delivered appliance is only guaranteed to operate safely if used for the
intended purpose. The specified limits may not be exceeded under any
circumstances.
Before ordering and installation, check that the hand pump is suitable for your
needs.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 9
4. Safety instructions
Before you install the User Manual, read through this operating manual
carefully. If the instructions contained within it are not followed, in particular
the safety guidelines, this could result in danger for people, the environment,
and the device and the system it is connected to.
The User Manual correspond to the state-of-the-art technology. This concerns the
accuracy, the operating mode and the safe operation of the device.
In order to guarantee that the device operates safely, the operator must act
competently and be conscious of safety issues.
TRADINCO provides support for the use of its products either personally or via
relevant literature. The customer verifies that our product is fit for purpose based
on our technical information. With this verification all hazards and risks are
transferred to our customers; our warranty is not valid.
4.1 Qualified personnel
The personnel who are charged for the installation and operation of the User
Manual must hold a relevant qualification. This can be based on training or
relevant tuition.
The personnel must be aware of this operating manual and have access to it
at all times.
4.2 General safety instructions
In all work, the existing national regulations for accident prevention and safety
in the workplace must be complied with. Any internal regulations of the
operator must also be complied with, even if these are not mentioned in this
manual.
Never use the hand pump together with an external pressure source. Do not
attach an external pressure generator to the hand pump.
Do not remove any attached components (test item, pressure hose, reference
gauge) when the hand pump is under pressure:
Open the pressure relief valve before removing any of the components.
Do not use Teflon tape to seal the pressure connections. Surplus Teflon tape
can enter the hand pump and damage it.
Only use adapters and seals that are available as accessories.
Non-pressurised storage: Only store the hand pump with the pressure relief
valve open. This ensures that no pressure can be built up by unintentional
pumping movements.
Avoid external force of all kinds towards the hand pump and its operating
elements.
Do not use the hand pump if it is damaged or defective.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 10
4.3 Special safety instructions
Warnings that are specifically relevant to individual operating procedures or
activities can be found at the beginning of the relevant sections of this operating
manual.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 11
5. Design and function
Operating elements:
Hand grips
Fine adjustment valve (handwheel)
Pressure relief valve (rotary knob)
'Pressure / vacuum' switch valve
(rotary knob)
Knurled nut (two parts with lock nut)
Connectors:
Connector reference gauge
Pressure hose with cap screw (test
item connection)
Main components:
Pump body
Piston rod with internal spring
5.1 Function
The test item respectively the pressure device to be tested (hereafter referred to
as 'test item') is connected to the cap screw of the pressure hose.
Pumping is carried out by repeatedly pushing the hand grips together (for a
vacuum, by pulling them apart). An internal spring returns the hand grips to their
start position.
The pumping movements are transferred to the pistons in the pump body via the
push rods.
Pressure or vacuum is generated there, depending on the switch valve setting.
The construction of the hand pump means that the same pressure/vacuum is
generated for the test item as for the reference test gauge.
The pressure or the vacuum is set to the necessary value using the fine
adjustment valve. Using the pressure relief valve, the pressure or the vacuum
can be reduced as needed or completely released. The generated pressure or
vacuum is displayed on the reference test gauge and compared with the
measurements of the test item.
The knurled nut is used to set the spring preload settings and limit the pumping
range.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 12
6. Initial setup
In order for the hand pump to be operated, it is vital that its connections with the
reference gauge and the test item are pressure-resistant. The pressure hose is
supplied already bolted on to the hand pump and should not be removed.
CAUTION! Material damage!
The test item must have absolutely nothing adhering to it (oil, grease, water
...).
Impurities can be transported into the hand pump via the pressure hose,
causing damage to the pump.
Maximum torque of the pressure connections!
Reference: 15 Nm
Test item: 15 Nm
Complete the following steps before use:
Screw the reference gauge tightly to the top of the hand pump with the
correct seal (Connector reference gauge G ¼).
Clean the connection of the test item and ensure that no oil or other
substances can enter into the pressure hose.
Select the suitable adapters and seals for the test item's connection.
Join the adapters and seals to the test item and the cap screw of the pressure
hose (G ¼). Whilst doing this ensure that the O-ring is correctly positioned in
the cap screw.
FIRST PUMPING PROCESS
The first pumping process can require a large amount of energy due to
adhesive forces.
Carry out the first pumping process with the pressure relief valve open.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 13
7. Operation
Generating pressure and generating vacuum not only differ in their operating
procedures and their range of settings, but also in the amount of energy needed
to work the operating elements.
Adhere to the following safety guidelines when operating the hand pump:
CAUTION! Crushing hazard!
During the pumping procedure ensure that fingers or other body parts are
kept away from the area between the hand grips and the piston rod.
CAUTION! Damage to switch valve!
Only operate the switch valve with the pressure relief valve open.
Using the switch valve under pressure causes damage to the hand pump
components.
CAUTION! Damage to valve stop!
If put under too much strain the stop and the hand pump will be damaged.
Only continue to tighten the valves (the fine adjustment, pressure relief
and switch valves) by hand, once the stop has been reached.
Before creating pressure or vacuum consider:
Before you create pressure or vacuum with the hand pump you should check for the
following requirements:
The reference gauge is connected to the hand pump.
The test item is joined to the pressure hose with the correct adapters and
seals.
All pressure connections are correctly in place, so that they resist pressure.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 14
7.1 Creating pressure
As the counter pressure of the test item increases, more energy is needed for the
pumping movements of the hand grips.
CAUTION! Damage to test item!
Adhere to the maximum pressure of the test item!
Only create an admission pressure with the hand grips that is lesser than the
necessary testing pressure. Following this carefully increase the pressure
using the fine adjustment valve.
In practical use the following operation methods have proved themselves to be
useful:
Operation with one hand:
Operation with both
hands:
Pumping against a base:
20 bar can be built up
safely and smoothly.
Above 20 bar, creating
pressure becomes
progressively more
difficult.
35 … 40 bar can be
generated quite quickly.
Above 40 bar the
pressure should be
increased with the fine
adjustment valve.
50 ... 55 bar can be
created in this way.
In this process it is
important that the lower
hand grip is placed on a
non-slip base.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 15
Pressure creation - operating steps
Switch on reference gauge and test
item (if necessary).
Close pressure relief valve:
•Turn the knob of the valve in a clockwise
direction until the stop is reached.
Set the switch valve to 'pressure':
•Turn the knob of the valve in a clockwise
direction until the stop is reached.
Create pressure:
•Push the hand grips together:
The pressure is built up.
•Repeat the pumping movements until the
necessary testing pressure has roughly
been reached.
Adjust the testing pressure.
The necessary testing pressure is precisely
adjusted with the fine adjustment valve:
• Turn the handwheel in a clockwise
direction to increase the pressure.
• Turn the handwheel of the valve in an
anti-clockwise direction to reduce the
pressure.
• Set the necessary testing pressure by turning the wheel as needed.
7.2 Increasing pressure with the fine adjustment valve
Alternatively, above ~ 20 … 30 bar you can
increase the pressure with the fine
adjustment valve.
Turn the handwheel in a clockwise
direction in the direction of the 'pump
body stop collar'. Depending on the
pressure of the test item and the setting
of the handwheel, pressure increases of
max. 15 …30 bar can be achieved quite easily.

FINE ADJUSTMENT VALVE
When it is not under pressure the fine adjustment valve moves very freely.
The wide handwheel of the fine adjustment valve can be moved into the
needed position very easily using with the palm of the hand.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 16
7.3 Creating vacuum
Vacuum creation - operating steps
Switch on reference gauge and test
item (if necessary).
Close pressure relief valve:
• Turn the knob of the valve in a clockwise
direction until the stop is reached.
Set the switch valve to 'vacuum':
• Turn the knob of the valve in an anti-
clockwise direction until the stop is
reached.
Create vacuum:
• Push the hand grips together:
The springs create the first negative
pressure, but cannot completely open the
hand grips.
• Now pull the hand grips apart until the
stop is reached.
• Push the hand grips together again: the
vacuum is increased.
• Repeat this process several times
(depending on the volume of the test
item) until the desired vacuum has been
reached.
Adjust the testing pressure.
The necessary testing pressure is adjusted
precisely with the fine adjustment valve:
• Turn the handwheel of the valve in a clockwise direction to decrease the
vacuum.
• Turn the handwheel of the valve in an anti-clockwise direction to increase
the vacuum.
• Set the necessary testing vacuum by turning the wheel as needed.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 17
7.4 Pressure / vacuum measurements
For adjustments, calibrations or an inspection of accuracy, it is vital that the test
item and the reference have the same pressure / vacuum.
The pressure / vacuum needed for the test points is built up and adjusted with
the hand pump (§ . 0 + 7.3).
The pressure relief valve makes a regulated, continuous decrease in pressure
possible, enabling measurements to be carried out accurately and simply even
when the pressure is falling.
The necessary procedures for measuring pressure or vacuum are configured by
the operator.
7.5 Carrying out the pressure or vacuum measurements
Carry out the necessary tests and measurements.
Document your results.
7.6 Completing the pressure or vacuum measurements
Once the pressure or vacuum measurements have been completed, the positive or
negative pressure in the hand pump, the test item and in the pressure hose need to be
brought into balance.
CAUTION! Risk of injury through excessive pressure!
Do not remove any connected components (test item, pressure hose,
reference gauge) if the hand pump is under pressure.
Open the pressure relief valve before removing any of the components.
Releasing pressure / equalising vacuum:
Turn the pressure relief valve knob 2-3 rotations in an anti-
clockwise direction and wait until there is no longer any
positive or negative pressure.
Remove the test item with adapters and seals from the
pressure hose.
Put the hand pump away along with any accessories which have been used.
(§ 10: "Maintenance/cleaning, storage and transportation")
REFERENCE GAUGE + PRESSURE HOSE
The common reference models fit into the gaps in the transportation case and
do not need to be removed. The pressure hose can also remain attached to
the hand pump. It should generally never be removed.
+p

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 18
8. Practical / usage guidelines
Preloading the springs / stroke limitation:
The preloading of the springs changes how much power the hand grips have to
reset themselves. The stroke limitation changes the size of the pumping strokes
and therefore the pumping volume of the hand pump.
The spring preload settings and the stroke limitation are set with the knurled nut.
KNURLED NUT
The knurled nut is made up of two parts. The upper part is used to adjust the
spring preload settings and the pumping stroke. The lower part is the lock nut
and fixes the setting.
8.1 Setting the spring preload / stroke limitation
Loosen the countering of the knurled nut.
Set the desired spring preload / pumping
stroke with the knurled nut.
Turn to the upper stop:
• the spring preload increases.
• the pumping stroke decreases.
Turn to the lower stop:
• the spring preload decreases
• the pumping stroke increases.
Fix the setting with the lock nut of the knurled
nut.
8.2 Pumping process
The pressure increase per pump stroke can be set with the stroke limitation and
the settings of the fine adjustment valve.
Furthermore the pressure increase is dependent on the current counterpressure,
the total volume of the test item and the energy of the pumping movements.
The following diagram shows, as an example, the pumping process with the hand
pump at different settings.
Stroke limitation:
max. pump stroke ()
min. pump stroke ()
Setting the fine adjustment valve:
Pump body stop collar (▬▬)
Storage / transportation (▬▬)
Pressure relief valve stop collar
(▬▬)

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 19
9. Problems
CAUTION! Material damage!
The hand pump cannot be repaired by the user. In case of a defect, the
device must be replaced or returned to the manufacturer for repair.
Never open up the hand pump and / or perform any repairs yourself.
The following table details what problems you can solve yourself and how to
solve them.
Problem
Possible cause
Remedy
Pressure cannot be built
up
(creation of vacuum).
Defective / incorrect seal.
Check seal (size / material /
wear).
Seal incorrectly positioned.
Check positioning of seal.
Pressure relief valve open.
Close pressure relief valve.
Switch valve in mid-position.
Turn the switch valve to the
desired position.
Pressure / vacuum fades
(unstable).
Leakage in the test item.
Check connections.
Check positioning of seals.
The first pump stroke is
stiff.
Not a defect. Due to adhesive
forces the first pumping
process requires a large
amount of energy.
Carry out the first pumping
process with the pressure
relief valve open.
Pumping stroke stiff.
High counter pressure in the
test item.
Increase the pressure with
the hand wheel of the fine
adjustment valve.

User Manual
TRAQC-5
P40 / P60
TRAQC-5 P40 / P60 & TRAQC-1 rev. 0 page : 20
10. Maintenance/cleaning, storage and transportation
10.1 Maintenance
No maintenance is required for the hand pump and it cannot be repaired by the
operator either. In the case of a defect the appliance must be sent back to the
manufacturer for repair.
Check the seals and O-rings for fractures and wear before use.
Replace defective or worn seals and O-rings.
10.2 Cleaning
Clean the hand pressure pump with a dry or slightly damp lint-free cloth.
Do not use sharp objects or aggressive cleaning agents to clean the pump. Avoid
contact with fluid or aggressive media.
10.3 Storage and transportation
For storage and transportation we recommend our transportation case, which is
available as an accessory.
The tight-fitting rigid foam inlay offers optimum protection for the hand pump
with pressure hose and accessories. A reference gauge of a suitable size can be
transported and stored in the case without being removed.
Before storage, we recommend that you consider the following points:
Clean the hand pump and the accessories.
Turn the fine adjustment valve in a clockwise
direction until the thread is no longer visible
(illustration).
Check that the switch valve is at its usual setting
(pressure/vacuum).
Open the pressure relief valve.
IMPORTANT! Do not store under pressure!
Only store the hand pump with the pressure relief valve open. This ensures
that no pressure can be built up by unintentional pumping movements.