TRAMPA VESC WAND User manual
DATA SCREEN
Press button 2 while on the main screen to view;
-Board Battery (%)
-Estimated Range (Km)
-Trip Distance (Km)
-Board Efficiency (Wh/Km)
-Remote Battery (%)
TEMPERATURE SCREEN
Press button 2 while on the Data Screen to view;
-VESC Temperature (C°)
-Motor Temperature(s) (C°)
LOCK / UNLOCK THROTTLE
Lock: Full Brake & any button
Unlock: Full Throttle & any button
HOME / MAIN SCREEN
Shows Speed, Power-consumption levels & Modes.
Power On: Button 1 or 2
Power Off: Hold Button 2 for 3 Seconds,
or depower/ step 5M away from Skateboard.
Swap Imperial & Metric: Hold buttons 1 & 2
together for 3 seconds
MODES:
R = Reverse
CC= Cruise Control
REVERSE
Reverse On/Off: Double Click Button 1
Reverse Cruise Control :Press Button 1 in reverse.
Smart Reverse: Hold full brake at a stand still
CRUISE CONTROL
Cruise Controlon: Click Button 1.
Cruise Controloff: Click Button one or move throttle.
Increase Speed: Hold Button 1
1 2
20
CC R
20
CC R
Button 2
Button 1
Full Brake
(Throttle pulled back)
Full Brake
Internal Magnet Finger Trigger Slot
2x AAA Batteries
(Not Included)
Carbon Battery Cover
Slider - visual Throttle Lever feedback
Speed (km/h or mph)
Power Consumption
CC / R - Shows what modes are active
Pistol Grip
mounting holes
Bottom Panel
Phillips Head
screw
Torx Head
screw (x5)
Before each ride, slowly push the Throttle Lever
fully forward & backward to ensure the throttle
input is correctly synced up to slider.
Lanyard
Loop
Throttle
Lever
Full Throttle
(Throttle pushed forward)
Full Throttle
OLED Screen
CNCed Aluminium housing
NEXT GENERATION
SKATEBOARD
CONTROLLER
Safety
Warnings:
VESC
Manuals:
More manuals & tutorials on our YouTube Channel.
Search forTRAMPA Boards Ltd on YouTube.
NEXT GENERATION
SKATEBOARD
CONTROLLER
Safety
Warnings:
VESC
Manuals:
1Follow the steps in the image below
NOTE THISCANNOT BE DONE WITH THE VESC APP
2Select SWD PROG and click CONNECT
3Select BLE TRAMPA from the included firmwares and click UPLOAD
4Once the upload is complete click DISCONNECT
5Disconnect the VESC and remove the SWD program cable.
Now your Connect NRF Dongle is readyto pair with the WAND
Flashing Guide
If you ownan existing TRAMPA VESC-Connect NRF Dongle, you may need to update the Firmware on
the Dongle before connecting the WAND. Your WAND comes witha program cable that plugs into the
SWDport & connects it a VESC, allowing FW updates.
1Power on the VESC and connect to it through the APP or DESKTOP TOOL
2Select INPUT configuartion wizard
3Select the VESC the NRF dongle is connected to (usually ‘This VESC’)
then clickNEXT
4Select NRF controller and click next
5You will see a pop-up box explaining that once you hit OK the VESC will ‘listen’
for the WAND for 10 seconds.
PLEASE ENSURE THE WAND IS OFF BEFORE PRESSING OK
6While the VESC is ‘listening’ press any button on the WAND to power it on.
You will see a pop-up confirming that the WAND is paired
7Finish the setup wizard, disconnect and you’re readyto ride!
Pairing Guide
Indepth Instructions found here:
WAND pairing instructions: https://vesc-project.com/node/940
Flashing Guidance:https://vesc-project.com/node/1113
Firmware update instructions: https://vesc-project.com/node/1114
This Wand remote comes with a basic Firmware & thefunctionality described on
the frontpage. The VESC WAND Firmware will getupdates over time. VESC-Tool
will inform you about available updates. Always use the latest version of
VESC-Tool &check for updates. We strive to keep your product updated &
functional as long as we possibly can.
Please use the VESC-Tool Profiles to modify the power of your board. Limit the
top speed & power levels while trying out &testing the WAND.Get used to the
handling & check for stable connectivity before riding with higher powers. Stay
safe!
SAFETY WARNING! Before riding your Board, please always check perfect
functionality. Never ride with a damaged remote or board! Always wear
appropriate full body safety gear when riding TRAMPA boards. Please carefully
read our generalsafety warning.
under warranty
