Tranquil Mount TMO400B User manual

INSTALLATION GUIDE
Support 32" to 52" Screens
Load Capacity: 7.0~28.5 lbs (3~13 kg)
VESA And Non-VESA compatible
100mm x 100mm
300mm x 200mm
200mm x 100mm
400mm x 200mm
300mm x 100mm
300mm x 300mm
400mm x 100mm
400mm x 300mm
200mm x 200mm
400mm x 400mm
www.tranquilmount.co.uk
Tranquil Mount
Model: TMO400B

2 of 8
WARNING
•
•
Be sure to read this entire manual thoroughly and you
•Sufficient expertise is required for installing this product. Be sure to subcontract the installation to a qualified person.
Ensure special attention to safety is paid during installation. Tranquil mount Ltd is not liable for any damage or
injury caused by mishandling or improper installation, or by installing anything other than the specified product.
Your Statutory Rights, (if any) are not affected.
If the safety precautions are not observed or the product is used incorrectly, it may result in serious injury or damage
to your wall and TV. This instruction manual shows the correct handling of the product and important precautions
necessary to prevent accidents. Be sure to read this manual thoroughly and use the product correctly. Keep the
manual available for future reference.
•Ensure your hands and fingers stay clear from the adjustable moving mechanics at the back of the bracket. This is
to avoid your fingers getting trapped. Please supervise children when this product is in use.
•This product is supplied with small parts for installation. For your children’s safety, please keep out of reach of chi-
ldren at all times.
fully understand all the instructions and warning before
attempting to begin your installation.
Before you begin installation, please verify that all components are included and undamaged. If any parts are missing or damaged,
contact Tranquil Mount Ltd or the store you purchased from. Never proceed with missing or damaged parts. Lay out all components
and make sure you identify that each one has a match in the diagram. Some of the parts included willnot be used during installation.
Do not proceed if you do not understand and identify all of the components.
We recommend in order to have a better installation, it is necessary to have in-wall wiring or wall AV and power plates installed to
hide the cords behind the wall. We advise you get a professional installer to do this.
Table of Contents
Parts List ........................................................................................................................................................................ 3
87,
Installation of Screen & adjustment of the spring pressure & Elevation adjustment
.......................................................
Installation of the bracket ........................................................................... ................................................................... 5, 6
.................................................... .................................................................................. ...........................
8
Product dimensions
Critical requirements of the installation . ... .. ... . ......................................................................................................... 4
Tools required for assembly
Required Tools Optional Tools
40mm
6mm 10mm
www.tranquilmount.co.uk
•This product should only be installed by someone who has a basic knowledge of buildings construction, installations
and fully understands these instructions.
•Make
•In order to have a better installation, it is necessary to have in-wall wiring or wall AV and power plates installed to
hide the cords behind the wall. We advise you get a professional installer to do this.
sure that the supporting surface will safely support the combined load of the mount, the display and all
attached hardware and components.
•This wall bracket will only support flat panel displays (LCD, Plasma). The maximum load capacity is 32kg.
•If mounting to a wall of wood stud construction, be sure that mounting bolt are anchored to the centre of the stud,
when installing the TV mount on a concrete wall, the wall must be at least 8"(203mm) thick with a minimum
compressivestrength of 2500 to 3000 psi (17.2 to 20.7 MPa), the concrete wall must meet ASTM C39. When installing
the TV mount on a cinder block wall, the cinder blocks must meet ASTM C216 specifications and have a minimum
nominal width of 8” (203mm). Be sure to mount in a solid part of the block, generally 1"(25 mm) minimum from the
side of the block. Do not drill into mortar joints! If plaster/drywall is thicker than 16mm, custom fasteners must be
supplied by the installer.
•Always have someone assist you to lift and position your equipment.
•T
•Screws must be tightly secured, but do not overtighten any screws (especially the four hex bolt screws M8x63.5mm)
or damage can occur and product may fail.
ighten screws and bolts firmly, but do not over tighten. Over tightening can damage the items and greatly reduce
their ability to hold. Please refer to suggested torque values where applicable in these instructions.

3 of 8
AA CC
DD
EE
BB
hook(x2)handle(x1)
front-panel(x1)
connecting rod(x1)
bracket(x1)
E
F
C
D
B
H
J
K
L
G
N
M
I
O
with your product.
Parts may appear slightly different than illustrated.
Before you b egin, make sure all parts shown are
included
Parts List
Description
A
KJI L M
A B C
D E F
G H
N
2
plastic washer(x4)
Hex bolt screw
M8x63.5 (x4)
washer (x4)
Expansion pipe
M10x60 (x4)
washer (x4)
screw M6x8 (x4)
screw M6x20 (x2)
screw M8x10 (x4)
1
Hexagon wrench
M8(x2)
O
Hexagon wrench
M5(x1)
M10(x1)
Cable Ties(x2)
4
4
4
4
4
4
4
4
M8x25
M8x12
M6x25
M6x12
6.2x16x1.5
philips pan head screw
washer(1)
4
philips pan head screw
philips pan head screw
philips pan head screw
4
4
M8x40
M8x35
philips pan head screw
philips pan head screw
4
spacer(1)
4
spacer(2)
M6x8
philips pan head screw
2M6x20
M8x10
philips pan head screw
allen pan head screw
4
M8x63.5
M10x60
4
8.2x1.5x16
washer(2) 4
Hex bolt screw
Expansion pipe
1 M10
1 M5
Hexagon wrench
Spanner
2 L150
Cable ties
Magentic Spirit Level
Magentic Spirit
Level(x1)
2 M8
Hexagon wrench
115x15x40
www.tranquilmount.co.uk
Spanner
6.2x16x1.5
washer(1)
M6
Non-slip nuts
Non-slip nuts(x4)

4 of 8
•Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and
components. Bracket installation need two people together to complete.
WARNING
CRITICAL requirements of the installation
If the equipment is installed above the fireplace, it is recom
mended that it is never turned on while the TV is in front or
located directly above the fire, However, the front edge of
mantle should never exceed110℉(43℃).
Mantle must not extend from mounting surface
more than 320mm.
The space above the mantle must be taller than the wallboard. The required space
depends on how far out the mantle extends. Refer to chart below and add this
additional height to wallboard height to determine if space is tall enough.
If the main wall is wooden, there must be at least 1 studs
available for mounting. If the main wall is concrete or brick
wall, please refer to the S4 installation points. Mind you,
the wall covering must not exceed 16mm thick.
TV weight must be between 7.0 ~28.5Ibs(3~ 13kg) and
have a screen size from 32” to 49”. Consult
Manual for verification.
TV Owner's
110°F
MAX.
350mm
MAXIMUM
2 STUDS
(These two studs need along the
mantel centre-symmetric, and
the centre distance between
two studs not more than 406mm)
If mantle extends:
Less than 180mm
180 - 240mm
240 - 300mm
300 - 350mm
This is required space height:
TV wallboard height plus 135mm
TV wallboard height plus 150mm
TV wallboard height plus 195mm
TV wallboard height plus 265mm
Wallboard height
Mantle
Extends
Space height
from 32” to 49”
12
3
5
4
WEIGHT:
7~28.5Ibs
(3~13kg)
C
L
www.tranquilmount.co.uk

www.tranquilmount.co.uk
5 of 8
Installation of the bracket
Measure the centreline of the mantle. Mark with tape on
the wall.
S1 S2
S4
Locate at least two studs with a stud finder. Locate the
centre of these studs by using a sharp awl or finish nail
poked through the drywall to locate each edge. Lag bolts
must be installed into the CENTRE of the studs.
C
L
C
L
Reference point 5 at page 4 to punch, please
make sure that the four mounting holes don't have
too big deviation.
S3
Cutout shown
for reference
C
L
C
L
C
L
4mm
CUTAWAY VIEW
INCORRECT
CORRECT
wall plate
plaster/
drywall
concrete
wall plate concrete
plaster/
drywall
Reference point 5 at page 4 to p unch, if the main
wall is concrete or brick wall, you must use the expansion
pipe we provided in M.
CL CL CL
plywood wall wood stud wall
CL
CAUTION CAUTION
Do not drill into mortar joints!
(68mm)
(10mm)
(68mm)
(4mm)
C
L
10mm
M
In order to have a better installation, it is necessary
to have in-wall wiring or wall AV and power plates
installed to hide the cords behind the wall. We
advise you get a professional installer to do this.
145mm
（5.7”）145mm
（5.7”）
50mm（1.97”）

6 of 8
Installation of the bracket
Take out EE L/N from the packaging, Detach EE and attach
through the hole as illustrated in the picture.
Take out K/DD/EE/N( ) from the
packaging, installation as illustrated in the picture.
S5 S6
Take out N/J from the packaging, lock the four allen pan head screws(M8x10) with Hexagon wrench in N, then use cable ties
in N to tie up the wires, as is shown in the pictures below.
S7
N
L
(magentic spirit level)
keep the up direction uniform
N
(Cable ties)
N
J
(Hexagon wrench M5)
(screw M8x10)
CAUTION
Don't over tighten!
www.tranquilmount.co.uk
the back wall plate to the wall. Then let the pre-set wire go
N
(spanner M10)
panner M10
EE
K
DD

7 of 8
Installation of Screen & adjustment of the spring pressure
Select the parts from the packaging,and according to your
TV situation to choose A+G; or B+G+H; or C; or D+H;
or E+H; or E+I; or F+H; or F+I, lock with cross screwdriver.
Take out J/AA/CC from the packaging, according to the
size of the TV, adjust to the approriate location, as shown
in the picture below, then lock with cross screwdriver.
S8 S9
Lift the TV through hooks for hanging onto the bracket panel,
then use a cross screwdriver to lock the two anti-off screws.
Adjust the spring pressure to the appropriate level with
energy saving wrench or O. Rotate clockwise to meet a
light tv (The present pressure is for around 13kg TV)
S11
S10
A/B (C/D/E/F don’t need G)
G
BB
H/I
(B/D/E/F need H/I, just
choose the suitable one)
AA
AA
CC
J
(screw M6x20)
J
(screw M6x8)
The energy saving wrench can be replaced by
O(hexagon wrench M8) which we provided.
_
_
+
+
counter-
clockwise
clockwise
www.tranquilmount.co.uk
6.0
11.0
16.0
19.0
22.0
26.0
30.0
KG
STOPLINE
!
STOPLINE
!
i
rp
s
ts
u
jA
e
l
b
a
ti
u
s
o
t
g
n
po t
n
e
r
e
f
f
i
d
n
o
n
o
i
t
i
s
.
t
h
g
i
e
w
d
a
o
l
ATTENTION
6.0
11.0
16.0
19.0
22.0
26.0
30.0
KG
STOPLINE
!
STOPLINE
!
Aj
t
s
uo
t
g
n
i
r
p
s
e
l
b
a
t
i
u
s
o
pi
t
i
st
n
e
r
e
f
f
i
d
n
o
n
o
lo e
w
d
a.
t
h
g
i
ATTENTION
Lose both screws to hang on:
Tighten both screws when hanging on.

8 of 8
TMO400B
www.tranquilmount.co.uk
S12
(The damping coefficient of the bracket's elevation angle is the factory value), the user can adjust the
weight of the device according to the elevation angle of the stent damping coefficient, the force to
match the actual requirements, so as to achieve satisfactory results.
tilt:-3°~+10°
Use the regulating handle
(we provided)
Tightening
(clockwise)
+
Loosing
(counter clockwise)
-
100 to400
Max to 400
445
425.0
swivel：±20°
°5±:level
140~425
Max to 470
°01+~°3-:tli
t
swivel:±20°
level：±5°
tilt:-3°~10°
TV:32” to 52”
load capacity: 3~13 KG
VESA: 100*100~400*400