Trap-it Abdlr-30 User manual

Caution: Always Wear Laser Protective Eyewear

OPERATION MANUAL

TRAP-IT® LR BEAM DUMP AND TARGET TRAP-IT® LR BEAM DUMP AND TARGET

DESCRIPTION

TRAP-IT™ low reectance beam dumps and targets are

designed to dissipate incoming laser power via heat dissi-

pation. The surface nish provides < 3.5% reectance from

190-10,600nm. Place these safety devices in a position along

the optical beam path to provide a nal beam stop.

For applications that range outside product specications,

we recommend that users expand the beam size with a

negative lens to lower the power density level.

2 .

REFLECTANCE GRAPH

TRAP-IT® LR BEAM DUMP AND TARGET TRAP-IT® LR BEAM DUMP AND TARGET

LASER SAFETY

Depending on the operating parameters of the laser source

and the potential for MPE (Maximum Permissible Exposure)

limits to be exceeded, there may be a signicant risk of eye

injury. Under such conditions, we recommend the use of

appropriate laser protective eyewear. Laser protective

eyewear must be evaluated in accordance with ANSI Z136.1

standard for the Safe Use of Lasers.

INSTRUCTIONS

1. Calculate your laser beam average power and maximum

power density.

2. Never place the product in a location above

the maximum suggested power density as damage could

occur to the product nish.

3. Position the laser beam centerline within the TRAP-IT™

target.

4. If this product is to be used as a control measure make

sure it is fastened to the table to prevent it from being

moved or knocked over.

3 .

4 .

TRAP-IT® LR BEAM DUMP AND TARGET TRAP-IT® LR BEAM DUMP AND TARGET

PREVENTIVE MAINTENANCE

Depending on the frequency of use and the number of

personnel that may have access to the laser application we

recommend you establish a daily or weekly inspection of

the product.

• Verify the product is in the correct orientation to the

incoming laser beam.

• Verify that the absorbing target surface hasn’t been

damaged by the laser.

• Clean with ethanol, IPA, or acetone, very light pressure

coating sensitive to physical damage.

COMPLIANCE

This product line is RoHS, Reach, ISO 9001:2015, AS9100

6 .

5 .

TRAP-IT® LR BEAM DUMP AND TARGET TRAP-IT® LR BEAM DUMP AND TARGET

WARRANTY

Kentek warrants TRAP-IT™ products to be free from defects

caused by faulty material or poor workmanship. Liability

under this warranty is limited to the obligation to repair or,

at Kentek’s sole option, to replace without charge, any part

found to be defective under normal use within one year

from date of invoice. Kentek must receive written

notication within the warranty time period stating what

defects were noticed, or what problems occurred with this

product. This warranty shall not apply to items that have

been subject to abuse or misuse after delivery, or to items

that have been altered in a means not authorized by Kentek

personnel.

Part Number Target Aperture Spectral Sensitivity Max. Average Power Damage Threshold Thermal Management

ABDLR-30 1.18 inch [30mm] 190-10,600nm 50 watts 20 watts/cm2Convection Cooled

ABDLR-30NP 1.18 inch [30mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled

ABDLR-51 2.00 inch [50.8mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled

ABDLR-51NP 2.00 inch [50.8mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled

ABDLRT-90 3.54 x 3.54 inch [90 x 90mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled

ABDLRT-90NP 3.54 x 3.54 inch [90 x 90mm] 190-10,600nm 50 watts 20 watts/cm Convection Cooled

ABDLRT-50 2.00 inch [50.8mm] 190-10,600nm 20 watts 20 watts/cm Convection Cooled

STAND-ITM Optical Stand with M6 Thread

TRAP-IT® LR BEAM DUMP AND TARGET TRAP-IT® LR BEAM DUMP AND TARGET