Treesat FMB920 User manual
Installation manual FMB920 - version 22.04.12
WARNINGS
Please read this manual before proceeding with the installation. All
connection activities should be performed with extreme caution. For
safety reasons, the module should be installed by qualified specialists.
DESCRIPTION
The kit consists of a small electronic device and a mobile or web application. The
communication module is mounted in the vehicle. The communication module monitors
the GPS position in real time with GNSS and GSM connectivity, collects device coordinates
and other useful data and sends them via the GSM network to the server. Communication
with the server and the application via the mobile network means that the user receives a
number of functions, e.g. a theft alarm with a map or an accident detection system
informing about a possible collision. The map and navigation will also help you find a
vehicle left in a parking lot or in a foreign city. There is also an ignition lock function.
Detailed functionalities of individual products can be found at treesat.io.
The device is ideal for applications where location acquisition of distant objects is
required. It can be used by companies with a car fleet, car rental companies, taxi
companies, and ordinary users using their own passenger cars.
[email protected] treesat.io
Installation manual FMB920 - version 22.04.12
MOUNTING THE DEVICE IN THE VEHICLE
When mounting the device in a vehicle, remember to avoid sensitive places that may
suppress the GSM and GPS signal. The best place to mount the device is its installation
under elements made of plastic, e.g.: upholstery, post, etc. The recommended, exemplary
location of the device is shown in the figure below.
CONNECTION AND WIRE DESCRIPTION
Color
Destiny
Installation tips
Red
Powering the device
Connect to a permanent power supply
Black
Device weight
Connect to ground
Yellow
Ignition switch (DIN1)
Ignition signal (not lost during start-up)
Gray
AIN1
Voltage input (connect plus from alarm
siren)
White
DOUT1
(locking/unlocking) Normal Open, ground
control, max 300 mA
[email protected] treesat.io
Installation manual FMB920 - version 22.04.12
IGNITION CUT-OFF CONNECTION DIAGRAM
Remote ignition cut-off is only possible for Car Assistant services
To be sure of operation, perform a function test
“Ignition cut off” in the mobile application.
Connection in the car
Relay pin description
[email protected] treesat.io
Installation manual FMB920 - version 22.04.12
OPERATION CHECK
After connecting the device, check its correct operation by observing the diodes.
Behavior of the “Status” LED (GSM):
●The LED blinks every second – normal operation, GSM signal has been stabilized.
●LED flashes every two seconds – GSM is in deep sleep mode.
●The LED flashes quickly for a short time – GSM is sending data to the server.
●Constant flashing of the diode – the device is being updated.
●The LED is off – faulty GSM modem.
Behavior of the “Navigate” LED (GPS):
●LED flashes every second – normal operation, GPS signal has been stabilized.
●The LED is not lit at all – the GPS module is turned off, the GPS is in deep sleep or
the GPS antenna has a short circuit.
●The LED is lit continuously – no GPS signal, the module is searching for satellites.
[email protected] treesat.io
Installation manual FMB920 - version 22.04.12
START PINS
1. Download the application on your phone, create an account, then log in.
2. Add the car (device) to your account in the app. The serial number is located
on the device, below the barcode .
3. It may take up to 24 hours for your device to activate. Using the user manual,
install the device in the vehicle after receiving a notification in the application about
the activation of the SIM card.
STARTING CAR ASSISTANT
1. Download the application on your phone, create an account, then log in.
2. Add the car (device) to your account in the app. The serial number is located
on the device, below the barcode.
3. It may take up to 24 hours for your device to activate. Using the user manual,
install the device in the vehicle after receiving a notification in the application about
the activation of the SIM card.
4. Check the operation of the device by arming and triggering an alarm in the
application. The device is ready for operation.
5. If the functional test did not take place under the target account in the
application (test account of the fitter), then Delete the vehicle (device) from the test
account: go to Vehicle details > click on the Settings icon (gear in the upper right
corner) > click on Delete vehicle. All data will be erased. Then add the device to your
customer account again.
STARTING FLEET MANAGER
1. Using the manual, install the device in the vehicle. Your device is already
active.
2. Log in to the Web application – you will receive login details by e-mail.
3. The device has been added to your account by Treesat. Create a vehicle in
the system and assign the number of the mounted device. Your devices are in the
drop-down list.
[email protected] treesat.io
Installation manual FMB920 - version 22.04.12
TECHNICAL SPECIFICATIONS
GSM
●Quad band 850/900/1800/1900MHz
●GPRS class 12
interface
●1 digital input, 1 analog input
●1 digital output NO
●accelerometer
●Internal high-gain GSM antenna
●Internal high-gain GNSS antenna
●2 device status LEDs
●Operating temperature: -20 °C to +60 °C
●Humidity: 5% to 95%
●IP54
●Dimensions: L(79mm) x W(43mm) x
H(12mm)
GNSS
●GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS
●Tracking: 33 channels
●Sensitivity -165 dBM
●Hot start <1s
●warm start <25s
●Cold start <35s
●Accuracy <3m
Power
●Power supply 6~30V DC, 1A Max.
●Integrated backup battery: 170 mAh
Li-Ion 3.7 V (0.63 Wh)
●Current consumption at 12V DC
●Sleep: <6mA
●Nominal operation: <35mA
●Maximum: < 1A
[email protected] treesat.io
Installation manual FMB920 - version 22.04.12
SIGNS
CE mark. This marking informs that the device complies with the terms of
Directive 2014/30/EU regarding the compliance of Member States with
electromagnetic compatibility regulations and the terms of Directive
2014/35/EU regarding compliance by Member States with low voltage
regulations and safety related to the operation of electrical equipment.
The symbol of the crossed-out waste bin attached to the product means that
the product is covered by the European Directive 2012/19/EU. Information on
separate collection points for waste electrical and electronic products can be
obtained from the place of residence. Please follow the guidelines of your
local authorities and do not dispose of this type of equipment with other
household waste. The correct disposal of your old products helps prevent
environmental pollution and loss of health.
If this logo is found on the product, it means that the fees related to the
appropriate recycling and recovery system have been paid.
This logo informs that the device is compliant with the terms of Directive
2011/65/EU (commonly known as the Restriction of Hazardous Substances
Directive or RoHS). The RoHS Directive covers restrictions at the production
stage on the introduction of hazardous substances in electronics.
CONTACT DETAILS
Treesat sp. z o.o
Wędkarska 38b
10-180 Olsztyn
[email protected] treesat.io
Table of contents
Other Treesat GPS manuals
