TRENDware TE100-H8E User manual

Quick Installation Guide
Note : Please read this quick installation Guide first.
PACKAGE CONTENTS
 The TE100-H8E Fast Ethernet 100Base-TX 8-port Mini Hub
 AC to DC (+12VDC 800mA) Power Adapter*
 This Quick Installation Guide
*Model: WP 481012D(for USA), WP481012DJ(for JPN)
WP 481012DV(for EUR), AM-12800B(for UK)
HARDWARE DESCRIPTION
The Front Panel
The front panel indicates LEDs status. The LED indicators monitor
the status of each port and connected segments. There are 5
different LEDs on the front panel; power (PWR), collision (COL),
Link/Activity, Error and Utilization.
LED Function Color Description
Power Green Lit : Power On
Unlit : Power Off
Collision Amber Lit : Data collision occurs
Link/Activity Green Lit : Indicates connected segment
Glitter : Receiving data
Error Yellow Flashing : Data error occurs
Lit : Indicates partition and port isolation
Utilization Green Indicates hub traffic
The Rear Panel
The rear panel contains the DC power socket, 8 Shielded Twisted-
Pair (STP) ports and one uplink slide switch.
Use any one of the STP ports for connecting to a 100Base-TX node
using Category 5 UTP/STP cabling. The uplink port provides
cascading capability to the second 100Base-TX Fast Ethernet hub.
The DC power socket is capable of accepting DC power input from
+9V to +12V.
HARDWARE INSTALLATION
Quick Installation Procedure
1. Place the TE100-H8E on a smooth surface.
2. Connect AC/DC power adapter to the wall jack and connect
power adapter’s plug to the DC power socket on the hub.
3. Connect workstations to the TE100-H8E by using Category 5
UTP/STP cabling.
Distance between the hub and the workstations can be no
more than 100 meters.
4. Connect each device (up to 8) to the TE100-H8E using the
same procedure in Step 3.
Uplink Multiple Hubs
If you would like to connect more than 8 Fast Ethernet devices, you
can use the uplink port cascading to another hub. In compliance with
IEEE802.3u Class II specification, two repeaters can be cascaded
using 5-meter cable in a single collision domain.
1. Connect a Category 5 UTP/STP cable to the Uplink port # 1 of
the first TE100-H8E. Uplink Switch should be set to Uplink
mode.
2. Connect other end of the cable to any available ports on the
second TE100-H8E. Note: If port 1 is used, make sure the
Uplink Switch is set to Node mode.
3. Connect workstations by using Category 5 UTP/STP cabling.
4. Connect each device (up to 8) to the TE100-H8E using the
same procedure in Step 3.
5. Connect AC/DC power adapter to the wall jack and connect
power adapter’s plug to the DC power socket on the hub.
Do not connect port # 1 of the first hub to port # 1 of the second
hub when both Uplink switches is set to the same mode.
Product Specifications

Standard IEEE802.3u, 100Base-TX Class II
Repeater
Number of 100Base-TX
ports
8
Uplink port Port # 1 (Sliding Switch)
Cable Distance 5 Meters for hub-to-hub
100 Meters for hub-to-workstation
Cabling UTP/STP Category 5 wiring
Expandability 14 ports on class II standard
LEDs Power – Green
Collision – Amber
8 Link/Activity – Green
8 Error – Yellow
4 Utilization – Green
Power Adapter AC to DC (+12V 800mA)
Temperature Operation 0oC to 50oC
Humidity 5% to 95% non-condensing
Dimensions 245 x 120 x 30 mm
Certification FCC Class A, CE, VCCI
Copyright Notice
Contents is subject to revision without prior notice.
All rights reserved.
Trademarks
All other trademarks belong to their respective owners.
FCC Compliance Statement
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules . These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
residential installation . This equipment generated, uses, and can
radiate radio frequency energy and if not installed and used in
accordance with the instruction manual may cause harmful
interference to radio communications. However, these is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected .
.Consult the dealer or an experienced radio TV technician for
help .
NOTICE:
I. The changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the equipment.
II. Shielded interface cables and AC power cord, must be used in
order to comply with emission limits.
CE Mark Declaration of Conformance
This is to certify that this product complies with ISO/IEC Guide 22
and EN45014. It conforms to the following specifications :
EMC : EN55022(1988)/CISPR 22(1985) Class A
EN60555-2(1987) Class A
prEN55024-2(1990)/IE801-2(1991) 4KV CD, 8KV AD
prEN55024-3(1991)/IE801-3(1984) 3V V/m
PrEN55024-4(1992)/IE801-4(1988) 1KV - (power line)
0.5KV - (signal line)
This product complies with the requirements of the Low Voltage
Directive 73/23/EEC and the EMC Directive 89/336/EEC.
TE100-H8E
ProXpress 100Base -TX
Mini Hub
User’s Guide
TRENDware international, Inc.
2421 W. 205th Street,
Torrance, CA 90501 U.S.A
Tel: [phone]
Fax: [phone]
www.trendware.com