Trinamic PANdrive PD-1021 User manual

Getting started PD-1021
TRINAMIC Motion Control GmbH & Co. KG
Hamburg, Germany
www.trinamic.com
STARTING UP
1. Connect the RS485 interface using pin 1, pin 3,
and pin 4 of the connector for power and RS485
communication.
Use an interface converter (e.g. USB-2-485)
between module and PC and install it.
2. Turn power ON. The green LED for power starts
flashing slowly and the motor is powered but
in standstill now.
If this does not occur, turn power OFF and
check your connections and power supply!
3. Start the TMCM-IDE program (see next page how
to configure the connection and to use the IDE)
4. Type in the open window:
ROL 0, 10000 //Rotate motor 0 with speed 10000
WAIT TICKS, 0, 500
MST 0
ROR 0, 10000 //Rotate motor 0 with speed 10000
WAIT TICKS, 0, 500
MST 0
5. Click the Assemble icon. Thereafter click the
Download icon to download the code to the
module. Click the Run icon. The program will
now be executed.
6. Click the Stop icon and start TMCL™Direct Mode
to issue the following commands:
ROR rotate right, motor 0, value 10000 -> click Execute
The motor is rotating now.
MST motor stop, motor 0 -> click Execute
The motor stops now.
FIRST STEPS ARE MADE.
Please refer to the PD-1021 Hardware and Firmware
Manuals, too.
YOU NEED
-PD-1021
-Power supply with nominal supply voltage of
+12 V or +24 V DC (9… 28 V DC)
-RS485 interface converter (e.g. USB-2-485)
-PC with TMCL-IDE program
(available from www.trinamic.com)
-Cables for interface and power
PRECAUTIONS
-Do not mix up connections or short-circuit
pins.
-Avoid bounding I/O wires with motor
power wires.
-Do not exceed the maximum power supply
of +28 V DC!
-Do not connect or disconnect the motor
while powered!
-START WITH POWER SUPPLY OFF!
QSH2818
Pin 1 B2
Pin 2 B1
Pin 3 A2
Pin 4 A1
Converter
e.g. USB-2-485
1
1
RS485
Pin 1 GND
Pin 3 RS485+
Pin 4 RS485-
Note, that the
GND pin has to be
used for the
power supply and
for the RS485
interface.
Power Supply
Pin 1 GND
Pin 2 9… 28V DC

Getting started PD-1021
TRINAMIC Motion Control GmbH & Co. KG
Hamburg, Germany
www.trinamic.com
TMCL-IDE
The TMCL-IDE is available on www.trinamic.com.
6. Click Assemble first, then Download and
Run to start the program.
Assemble
Download Run StopDissemble Continue
7. Stop all running programs by clicking
Stop and start Direct Mode by clicking the
appropriate icon.
8. The PD-1021 is automatically detected, if
the communication is established.
9. Issue a command by choosing Instruction,
Type, Motor, and Value and click Execute
to send it to the module.
1. Make sure the COM port you intend to
use is not blocked by another program.
2. Open TMCL-IDE by clicking TMCL.exe.
3. Choose Setup and Options and
thereafter the Connection tab.
4. Choose COM port and Type. Click OK.
5. Enter the program code and save it with
File/Save.
Note, that TMCL programs run
standalone on the module, too.
TROUBLESHOOTING
IF COMMUNICATION IS NOT ESTABLISHED
-Check if the green LED lights up. If not,
check your power supply.
-Try to start Direct Mode and check, if the
module is detected automatically.
-Check, if you are using the right COM port
and it is not blocked by another program.
-Check, if the file TMCM-1021.inf is installed
correctly.
-Check your connection settings. Default: 9600
baud, address 1.
-Check if your RS485 converter functions.
IF MOTOR DOES NOT RESPOND
-Usually the communication is not
established (see above).
-Check the motor connection.
-If you are using a TMCL program try a
movement command in Direct Mode to
check if there is a problem with it.
-Restore factory settings by using instruction
137 for cancelling all settings modified by
the user.