Tripp Lite AG-0072 User manual

1
Owner’s Manual
Warranty
Registration
Register online today for a
chance to win a FREE Tripp Lite
product! www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/supportCopyright © 2013 Tripp Lite. All rights reserved. SmartPro®is a registered trademark of Tripp Lite.
Important Safety Instructions 2
Mounting 4
Quick Installation 6
Optional Installation 7
Basic Operation 9
Storage and Service 17
Battery Replacement 18
Warranty Registration 24
Español 25
Français 49
Русский 73
SmartPro®2U Rackmount
Intelligent, Line-Interactive UPS Systems230V Sine Wave Output • 1000VA—3000VA Capacities
Extended Runtime OptionsSMX1000RT2U
(Series Number: AG-0072)
SMX1500XLRT2U
(Series Number: AG-0071)
SMX2200XLRT2U
(Series Number: AG-0070)
SMX3000XLRT2UA
(Series Number: AG-0069)
Not suitable for mobile applications.
13-09-242-93-3184.indb 1 12/9/2013 10:13:37 AM

2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during the installation,
operation and storage of this product. Failure to heed these warnings may affect the warranty.
UPS Location Warnings
•UsecautionwhenliftingtheUPS.BecauseoftheconsiderableweightofallrackmountUPSsystems, at least two people should assist in lifting and installing them.
•InstalltheUPSindoors,awayfromexcessmoistureorheat,dustordirectsunlight.•Forbestperformance,theambienttemperatureneartheUPSshouldbebetween0°Cand40°C(between32°Fand104°F).•LeaveadequatespacearoundallsidesoftheUPSforproperventilation.Donotobstructitsventsor fan openings.
•WhenmountingtheUPSsysteminatowerorientation,makesuretheLCDScreenpanelisatthetopoftheUPS,notatthebottom.•Donotmountunitwithitsfrontorrearpanelfacingdown(atanyangle).Mountinginthismannerwill seriously inhibit the unit’s internal cooling, eventually causing product damage not covered
under warranty.
UPS Connection Warnings
•TheUPScontainsitsownenergysource(battery).TheoutputterminalsmaybeliveevenwhentheUPSisnotconnectedtoanACsupply.•ConnecttheUPStoaproperlygroundedACpoweroutlet.DonotmodifytheUPS’spluginawaythatwouldeliminatetheUPS’sconnectiontoground.DonotuseadaptersthateliminatetheUPS’sconnectiontoground.•ThepoweroutletthatsuppliestheUPSshouldbeinstalledneartheUPSandbeeasilyaccessible.
•DonotplugtheUPSintoitself;thiswilldamagetheUPSandvoidyourwarranty.•IfyouareconnectingtheUPStoamotor-poweredACgenerator,thegeneratormustprovidefiltered,frequency-regulatedcomputer-gradeoutput.ConnectingtheUPStoageneratorwillvoiditsUltimateLifetimeInsurance.Equipment Connection Warnings
•Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonablybeexpectedtocausethefailureofthelifesupportequipmentortosignificantlyaffectitssafetyoreffectivenessisnotrecommended.Donotusethisequipmentinthepresenceofaflammableanestheticmixturewithair,oxygenornitrousoxide.•DonotconnectsurgesuppressorsorextensioncordstotheoutputoftheUPS.ThismightdamagetheUPSandmayaffectthesurgesuppressorandUPSwarranties.13-09-242-93-3184.indb 2 12/9/2013 10:13:37 AM

3
Battery Warnings
•Batteriescanpresentariskofelectricalshockandburnfromhighshort-circuitcurrent.Observeproperprecautions.Donotdisposeofthebatteriesinafire.DonotopentheUPSorbatteries.Donotshortorbridgethebatteryterminalswithanyobject.UnplugandturnofftheUPSbeforeperformingbatteryreplacement.Usetoolswithinsulatedhandles.Therearenouser-serviceablepartsinsidetheUPS.Batteryreplacementshouldbeperformedonlybyauthorizedservicepersonnel using the same number and type of batteries (Sealed Lead-Acid). The batteries
arerecyclable.Refertoyourlocalcodesfordisposalrequirementsorvisitwww.tripplite.com/UPSbatteryrecyclingforrecyclinginformation.TrippLiteoffersacompletelineofUPSSystemReplacementBatteryCartridges(R.B.C.).VisitTrippLiteontheWebatwww.tripplite.com/support/battery/index.cfmtolocatethespecificreplacementbatteryforyourUPS.TheRBCTypecanalsobefoundonthelabelaffixedtotheBatteryRetentionPlate.•Duringhot-swapbatteryreplacement,theUPSwillnotprovidebackuppowerintheeventofablackout or other power interruptions.
•DonotoperatetheUPSwithoutbatteries.External Battery Connection Warnings
•Whenaddingexternalbatterypackstoselectmodelswithexternalbatterypackconnectors,connectonlyTrippLite-recommendedbatterypacksofthecorrectvoltageandtype.DonotconnectordisconnectbatterypackswhentheUPSisoperatingonbatterypower.
Visitwww.tripplite.com/support/battery/index.cfmtolocatethesupportedbatterytype(s)foryourUPS.Important Safety Instructions
13-09-242-93-3184.indb 3 12/9/2013 10:13:37 AM

4
A
AB
C
CB
1
2
3
4
DD
Mounting (Rack)
Mountyourequipmentineithera2-postor4-postrackorrackenclosure.Theusermustdeterminethefitnessofhardwareandproceduresbeforemounting.Ifhardwareandproceduresare not suitable for your application, contact the manufacturer of your rack or rack enclosure. The
procedures described in this manual are for common rack and rack enclosure types and may not
be appropriate for all applications.
Note: The illustrations may differ from your model.
4-Post Mounting
1The included plastic pegs Awill temporarily
support the empty rackmount shelves B
while you install the permanent mounting
hardware.Insertapegnearthecenterofthe front and rear bracket of each shelf as
shown. (Each front bracket has 6 holes and
each rear bracket has 3 holes.) The pegs
will snap into place.
Afterinstallingthepegs,expandeachshelfto match the depth of your rack rails. The
pegswillfitthroughthesquareholesintherack rails to support the shelves. Refer to
the rack unit labels to confirm that the
shelves are level in all directions. Note: The
support ledge of each shelf must face
inward.
2Secure the shelves Bto the mounting rails
permanently using the included screws and
cup washers Cas shown. Place the cup
washer between the screw and the rack so
that the screw enters the wider opening of
the cup washer first.
Place4screwstotalatthefrontand4screws total at the back.
Tighten all screws before proceeding.
Warning: Do not attempt to install your equipment until you have inserted and tightened the required screws. The plastic pegs will not support the weight of your equipment.3Attachyourequipment’smountingbracketsto the forward mounting holes of the
cabinet using the hardware included with
yourequipment.Themountingbracket“ears” should face forward. (Some
equipmentmayhavepre-installedorintegral mounting brackets.)
4Withtheaidofanassistant(ifnecessary),liftyourequipmentandslideitintotheshelves.Attachtheequipmentmountingbrackets to the forward mounting rails with
user-supplied screws and washers D.
Tighten all screws securely.
13-09-242-93-3184.indb 4 12/9/2013 10:13:42 AM

5
Mounting (Rack) continued
2-Post Mounting
2-postmountingrequiresaTrippLite2-PostRackmountInstallationKit(model:2POSTRMKITWM,sold separately).
Mounting (Tower)
Warning: When mounting the UPS system in a tower orientation, make sure the LCD Screen panel is at the top of the UPS, not at the bottom.Note: To mount the UPS in an upright (tower) position, 2-9USTAND is required (sold separately).
RotatetheLCDScreenpanelforeasyviewingwhiletheUPSistowermounted.Insertasmallscrewdriver, or other tool, in the slots on either
side of the panel. Pop the panel out, rotate it
and pop the panel back in place.
13-09-242-93-3184.indb 5 12/9/2013 10:13:43 AM

6
2
3A
1
Quick Installation
1Insert a user-supplied power
cord (with country-specific
plug) into the UPS Systems
IEC inlet connection. Plug the
other end into your country-
specific wall outlet.*
NOTE! After you plug the UPS into a live AC outlet, the UPS (in “Standby Mode”) will automatically charge its batteries, but will not supply power to its outlets until it is turned ON.*See the UPS systems nameplate for input
requirements. Additional input cords are also
available from Tripp Lite.
2Plug your equipment into
the UPS.*
AdditionalC13-to-C14interconnectioncord(s) are included to connect your
equipmenttotheUPS.NOTE: Additional interconnection cords are
available from Tripp Lite.
* Your UPS is designed to support only electronic
equipment. You will overload the UPS if the total
VA ratings for all the equipment you connect
exceeds the UPS’s Output Capacity. To find your
equipment’s VA ratings, look on their
nameplates. If the equipment is listed in amps,
multiply the number of amps by 230 to
determine VA. (Example: 1 amp × 230 = 230
VA). If you are unsure if you have overloaded
the UPS’s outlets, see LOAD icon description in
LCDInterfacesection underBasicOperation.
3Turn the UPS ON.
Press and hold the button Afor one
second. The alarm will beep once briefly.
Note: UPS system will function properly upon
initial startup, however, maximum runtime and a
successful self-test will only be accessible after it
has been charged for 24 hours.
13-09-242-93-3184.indb 6 12/9/2013 10:13:45 AM

7
1A
1B
2A
4-5
2B
Optional Installation
These connections are optional. Your UPS will function properly without these connections.
1USB and RS-232 Serial
Communications
UsetheincludedUSBcable(see1A) or
DB9serialcable(see1B) to connect the
communication port on your computer to
thecommunicationportofyourUPS.Installon your computer the Tripp Lite PowerAlert
Software appropriate to your computer’s
operating system.
2EPO Port Connection
This optional feature is only for those
applicationswhichrequireconnectiontoafacility’sEmergencyPowerOff(EPO)circuit.WhentheUPSisconnectedtothiscircuit,itenablesemergencyshutdownoftheUPS’sinverter.
Usingthecableprovided,connecttheEPOportofyourUPS(see2A) to a user-supplied
normally closed or normally open switch
according to the circuit diagram (see 2B).
TheEPOportisnotaphonelinesurgesuppressor;donotconnectaphonelinetothis port.
13-09-242-93-3184.indb 7 12/9/2013 10:13:48 AM

8
3
A
Optional Installation continued
3External Battery Connection
(Select Models)
YourUPScomeswitharobustinternalbatterysystem;externalbatteriesareneededonlytoextendruntime.Addingexternalbatterieswillincreaserechargetime as well as runtime. Contact Tripp Lite
tofindoutwhichexternalbatterypacksyour model supports.
The illustration (see 3)showsthelocationofyourUPS’sExternalBatteryConnectorAwhere
you will insert the battery pack cable. Complete installation instructions for your battery pack
appearinthebatterypackowner’smanual.Makesurethatcablesarefullyinsertedintotheirconnectors.Smallsparksmayresultduringbatteryconnection;thisisnormal.DonotconnectordisconnectbatterypackswhentheUPSisrunningonbatterypower.Caution! When an external battery pack is connected, make sure the AC load does not exceed the nameplate rating. Select models are derated when an external battery pack is connected. See UPS nameplate label for derating details.WhenconnectingexternalbatteriestotheUPS,gototheTrippLitewebsiteat
www.tripplite.com/en/support/bpconfig/index.cfmtodownloadtheExternalBatteryPackUtilitysoftwaretoconfigureyourUPSforexternalbatterysupport.Note:
1. The runtime and charge rate will automatically recalculate once the External Battery Pack Tool process is
complete.
2. If the setup will no longer include external batteries, the UPS can be configured to work without external
batteries via the LCD Screen. See ExternalBatterySettingsControlsection under BasicOperationfor
details.
3. If external battery packs are removed, the UPS must be reset to “NO EXTERNAL BATTERY” via the LCD
interface or the External Battery Configuration Program available on the Tripp Lite website. Failure to do
so may result in damage to the internal batteries due to over-charging.
13-09-242-93-3184.indb 8 12/9/2013 10:13:50 AM

9
Note: This LCD image is shown
with all icons illuminated. Under
normal conditions, only select
icons will be lit.
Basic Operation
LCD Interface
3-Digit Display: This display is generally used to show values for a given
“Display”or“Control”screen.“ON/OFF” Button• To turn the UPS ON:AfteryouplugtheUPSintoaliveACoutlet,theUPS(in”Standby” mode) will automatically charge its batteries, but will not supply
powertoitsoutletsuntilitisturnedON.WiththeUPSpluggedintoaliveACwalloutlet,pressandholdthe“ON/OFF”buttonforonesecond.*TheUPSwillbeeponcetoindicateONstatus.Releasethebutton.• To cold-start the UPS:Ifutilitypowerisabsent,youcan“cold-start”theUPS(i.e.:turnitONandsupplypowerforalimitedtimefromitsbatteries)bypressingandholdingthe“ON/OFF”buttonforonesecond.*TheUPSwillbeeponcetoindicateONstatus.Releasethebutton.• To turn the UPS OFF:WiththeUPSONandreceivingutilitypower,pressandholdthe“ON/OFF”buttonfor2.5seconds.*TheUPSwillbeeponcetoindicateOFFstatus.ThenunplugtheUPSfromthewalloutlet.TheUPSwillbecompletelyOFF.* If the user unintentionally presses the ON/OFF button, the OFF function can be
temporarily canceled by continuing to hold the ON/OFF button until the UPS beeps and
then momentarily pressing either the MODE button or the ENTER/MUTE button. Once
both buttons are released, the UPS will remain ON.
“MODE” ButtonTo enable viewing of power displays and control menu options, tap this button.
See“DisplayPowerConditions”&“ControlMenuOptions”fordetails.• CanbeusedinconjunctionwiththeON/OFFbuttontocancelthe“OFF”function.See“ON/OFFButton”instructionsabove.• CanbeusedinconjunctionwiththeENTER/MUTEbuttontorestoretheLCDtoFactoryMode.See“ControlMenuOptions”.13-09-242-93-3184.indb 9 12/9/2013 10:13:51 AM

10
Basic Operation continued
“ENTER/MUTE” ButtonTo toggle settings options while viewing a control menu option, tap this button.
TheUPSpowerfailurealarmcanalsobetemporarilysilencedbytappingthisbutton.Oncesilenced,analarmwillautomaticallyre-soundtoindicatelowbattery conditions and can no longer be silenced.
•CanbeusedinconjunctionwiththeON/OFFbuttontocancelthe“OFF”function.See“ON/OFFButton”instructionsabove.•CanbeusedinconjunctionwiththeENTER/MUTEbuttontorestoretheLCDtoFactoryMode.See“ON/OFFButton”instructions.Note: Alarm-free silent operation is available by setting the alarm to disable
(see CONTROL MENU OPTIONS / ALARM ENABLE-DISABLE section).
Battery Capacity:Thiswillbeactiveinall“Display”modes,butisnotshownin “Control” modes.
AC Input:ThisindicatesthattheunitisrunninginLineModeandsupplyingACpowertoequipmentconnectedtotheoutput.Battery Input:ThiswillflashtoindicatethattheUPSisnotreceivingACinputandisrunningininvertermode.TheBatteryInputiconisalsousedinconjunctionwiththeEVENTSicontoindicateOnBatteryevents.Replace Battery Icon: IntheeventthatUPSbatteriesexpireandrequirereplacement, this icon and the warning icon will flash. This icon will also flash
afterafailedUPSself-test(seetheBASICOPERATION/CONTROLMENUOPTIONS/SELF-TESTsectionformoreinformation).Warning: This will flash to let the user know that there’s a warning condition
and immediate action must be taken:
1.ForReplaceBattery:ReplaceBatteryandWarningiconsflashduringanynormal“Display”mode.2.ForOverload:Load,WarningandLoadPercentageiconswillflash,thealarmwillsoundrepeatedlyandtheLCDscreenwillswitchfromtheuser-selecteddisplaymodetoLoadPercentage.OverloadindicationisavailableinbothACandbatterymodes.CAUTION!AnyoverloadconditionthatisnotcorrectedbytheuserimmediatelymaycausetheUPStoshutdownandceasesupplyingpower in the event of a blackout or brownout.
EVENTS Icon:DisplayedinconjunctionwiththeAVRiconandBATTiconstoindicatethenumberofOnBatteryorAVReventsthathaveoccurred.Alarm Off:Indicatesthatthealarmisdisabled.Alarm On: Indicatesthatthealarmisenabled.13-09-242-93-3184.indb 10 12/9/2013 10:13:52 AM