Tripp Lite DWM1742S User manual

1
Owner’s Manual
Full Motion
Flat Screen Wall Mount
MODEL: DWM1742S
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2020 Tripp Lite. All rights reserved.
100x100
200x100
200x200
42”
MAX
20 kg
20 kg
(44 lbs)
(44 lbs)
Este manual esta disponible en español en la página de Tripp Lite: tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Tripp Lite по адресу: tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: tripplite.com
WARRANTY REGISTRATION
Register your product today and be
automatically entered to win an ISOBAR
surge protector in our monthly drawing!
tripplite.com/warranty

2
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and a full understanding of this instruction
manual.
• Make sure that the mounting surface can safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
• Use of this equipment in life support applications where failure of this equipment
can reasonably be expected to cause the failure of the life support equipment or
to significantly affect its safety or effectiveness is not recommended.

3
Warranty & Warranty Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and
illustrations may differ slightly from actual products.

4
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
installing. If any parts are missing or faulty, visit www.tripplite.com/support for service.
DWM1742S
4mm Hex Key (x1) 6mm Hex Key (x1)
Wrench (x1)
Nut (x1) M8 Hexagon Nut (x1) D8 Washer (x1)
D5 Washer (x4)
M4X14 (x4)
Anchor Bolt (x3) Concrete Anchor (x3)
D8 Washer (x4)
M5X14 (x4)
Small Spacer (x8)
M6X14 (x4) M8X20 (x4)
Package M
Package W

5
1. Separate VESA Plate from Wall Mount
2. Remove the Decorative Covers
• Using the supplied wrench, loosen the two
upper knobs
• Remove both lower knobs
• Remove VESA plate
Wrench

6
3a. Mount on Wood Stud Wall
3
Mark the exact location of the
mounting holes
Screw the wall
mount onto
the wall
Drill pilot holes
WARNING
• Make sure that mounting screws are anchored into the center of the studs.
Use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
Find a wood stud location for
mounting the wall mount
12
Anchor Bolt

7
3b. Mount on Solid Brick and Concrete Block
WARNING
• When installing wall mounts onto a concrete masonry unit (also known as a CMU or
“cinder block”), verify that the actual concrete thickness is at least 35mm (1-3/8”)
in order to hold the concrete anchors. DO NOT DRILL INTO MORTAR JOINTS! Be sure
to mount the wall mount with the included concrete anchors and anchor bolts onto
solid sections of the blocks. The solid sections can generally be found 25mm (1”)
toward the middle of the block from either end. An electric drill on a slow setting is
suggested to drill the hole rather than a hammer drill so as to avoid breaking out the
back of the hole when entering a hollow section.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
Screw the wall
mount onto
the wall
Drill pilot holes
2
Find and mark the
exact location of
mounting holes
1
Concrete Anchor
Anchor Bolt

8
4. Install Decorative Covers
5. Install VESA Plate
Top of Display
Wrench
D8 Washer
Nut
M8 Hexagon Nut

9
5. Install VESA Plate
Note: Firmly secure the VESA plate to the display using the appropriate screws, washers and spacers
(if necessary).
Do not over-tighten screws.
or
M8x20 M8x20
M4X14 / M5X14
M6X14 / M8X20
D5 Washer
D8 Washer
D8 Washer
Small Spacer Small Spacer
Small Spacer
D8 Washer
TV

10
6. Hook the TV onto the Wall Mount
· Position a level on the horizontal and vertical sides of the display and adjust as needed.
· Reattach the lower knobs to the VESA mount (removed in step 1). Using the supplied wrench, tighten all
upper and lower knobs.
Using an assistant or mechanical lifting equipment, lift the display with attached VESA plate. Set the
VESA plate’s upper thumbscrews over the top flange of wall plate arm. Make sure the VESA plate’s
lower screws fit inside of the wall plate arm’s lower hole.
4mm