2 3
PS10001
1000W
500W
240W
1%
600W
20Hz ~ 150Hz
90dB
0.2 ~ 6V
50Hz ~ 150Hz
260
Adjustable 0-12dB
45Hz
6.42”x5.12”x1.97”
PS15006
1500W
120W x 6
85W x 6
1%
2000W
20Hz ~ 25kHz
80dB
0.2 ~ 6V
50Hz ~ 500Hz
260
Adjustable 0-12dB
45Hz
10.75”x5.12”x1.97”
II.
Model
Peak Power
Power RMS 2Ω @ 14.4V
Power RMS 4Ω @ 14.4V
THD+N @ Nominal Power
THD+N @ 10% Nominal Power
Frequency Response (-3db)
SNR
Low Pass Filter
Damping factor (Nominal
Impedance @ 100Hz)
Bass Boost
Bass Boost Center Frequency
Dimensions
PS10004
1000W
120W x 4
85W x 4
X200W x 3
Power RMS Bridged 4Ω @ 14.4V
200W x 2
1%
1500W
20Hz ~ 25kHz
80dB
0.2 ~ 6V
50Hz ~ 500Hz
50Hz ~ 500Hz
High Pass Filter 50Hz ~ 500Hz X
260
Adjustable 0-12dB
45Hz
8.38”x5.12”x1.97”
11.(+)12 Volt Power
Connect this terminal through a FUSE or CIRCUIT BREAKER to the posive terminal
the vehicle baery or the posive terminal of an isolated audio system baery.
Wamning:Always protect this power wire by installing a fuse or circuit breaker of the appropriate
size within 12 inches of the baery terminal connecon.
12.FUSE
These fuses protect the amplifier against internal electrical damage and are meant to protect the amplifier only. All
other power connecons should be fused at the source.
PS1000.1:30A X 2 PS1000.4: 30A X 2 PS15006: 30A X 2
13.LED
Will illuminate Green to indicate the amplifier is on and operang normally, and will be illuminated RED if the
amplifier shuts down due to short circuit, DC offect, or overheang
detected by on board protecon circuitry
1.RCA input jacks
These RCA input jacks are for use with source units that have RCA or Line level outputs.A source unit with a minimum
level of 200mV is required for proper operaon. The use of high quality twisted pair cables is recommended to decrease
the possibility of radiated noise entering the system.
2.GAIN Control
The level control will match the amplifiers sensivity to the source units signal voltage.
The Operang range is 200mV minimum to 6V maximum.
CAUTION:Do not run the amplifier in high volume for long me,otherwise the loudspeakers will be damaged.
3.Full pass x-over switch
When the switch is in the"Full"posion,the full range is bypassed.
4.Low pass x-over switch
When the switch is in the "LPF"posion,frequencies lower than the low pass frequency
seng are passed.
4.1 Low pass x-over frequency control
This control is used to select the desired low pass x-over frequency.
The frequency can be adjusted between 50Hz and 500Hz.
5.High pass x-over switch
When the switch is in the"HPF"posion,frequencies higher than the high pass
frequency seng are passed.
5.1 High pass x-over frequency control
This control is used to select the desired high pass x-over frequency
The frequency can be adjusted between 50Hz and 500Hz.
6.Bass Boost
The boost can be adjusted between 0dB to12dB
7.Wireless Remote Sub Level Control
Controls the subwoofer amplifier gain,from a remote locaon for ease of adjustment
during listening.
Model:PS1000.4 Low pass x-over swith(3/4CH)
To use the wireless remote sub control set switch to “LPF”
Model:PS1500.6 Low pass x-over swith(5/6CH)
To use the wireless remote sub control set switch to “LPF”
8.PHASE
0-180 selectable for switching the phase of the output to the woofer.
9.GND
Connect this terminal directly to the sheet metal chassis of the vehicle,using the
shortest wire necessary to make this connecon.Always use wire of the same gauge
or larger than the (+)12 volt power wire.The chassis connecon point should be
scraped free of paint and dirt.Use only quality crimped and/or soldered connectors
at both ends of this wire.
Warning:Do not connect this terminal directly to the vehicle baery ground terminal or any other
factory ground points.
10.Remote Turn On
This terminal turns on the amplifier when (+)12 volt is applied to it.Connect it to the
remote turn on lead of the head unit or signal source.
CONTROL FUNCTIONS:
