Triumph Sports USA 45-6074 User manual

Item# 45-6074
If you have any problems with your new product,
please contact Triumph Sports USA at 1-866-815-4173,
or e-mail us at [email protected]
for any technical support or warranty issues.
Please keep this instruction manual for future reference
4-Piece Table Tennis Table

A PURCHASE RECEIPT (or other proof of purchase date) will be required before any
warranty service is initiated. All requests for warranty service can be submitted by email, in
writing or by contacting our Customer Service Department at:
1-866-815-4173 or email us at [e-mail].
IMPORTANT NOTICE! Please contact us before returning the product to the store.
All Triumph Sports USA, Inc. (TSU) games have a limited 90-day from date of purchase
warranty. This warrants the retail purchaser for any TSU game purchased to be free from any
defect in materials and construction for 90 days from the date of purchase. The only exceptions
to the warranty include main frames, tabletops, playing surfaces, batteries or tools. Damaged
main frames, tabletops, playing surfaces need to be returned to the store as we are unable to
replace these parts. Normal play wear and usage is not covered under the warranty, nor is wear
or damage due to improper use of the TSU game. This will void any and all TSU warranties.
Limited 90-Day Triumph Sports USA, Inc. Warranty
Triumph Sports USA
11327 W Lincoln Ave.
West Allis, WI 53227
www.triumphsportsusa.com
©2014 Triumph Sports USA. All Rights Reserved.
Warnings
WARNING:Choking Hazard—Product contains small balls and/or small parts.
Not for children under 3 years of age.

Parts List
1 2 3 4
5 6 7 8
9 10 11
P1 P2
Table Surface-A
2pcs Table Surface-B 2pcs Table Tennis Paddle
2pcs
PRE-INSTALLED PARTS
13 14
12
15 16
17 18 19 20
21 22 A1 A2
A3 A4 A5 A6
A7 A8 A9
Table Tennis Ball
2pcs
Curved Outer Leg
with Cap 2pcs Curved Inner Leg with Cap 2pcs Linkage Tube
with Stop Bracket 2pcs Linkage Tube 2pcs
Bracket
6pcs Gravity Lock
2pcs End Apron
(1.35m) 2pcs Side Apron
(1.25m) 4pcs
Safety Strap – Long
1pc Safety Strap – Short
2pcs Net 1pc Net Post 2pcs
Plastic Corner
4pcs Wheel 4pcs Leg Bracket - A
8pcs Leg Bracket - B
4pcs
Plastic Panel with
Frame 2pcs “T” Washer
2pcs M4 X 12MM Screw
47pcs M6 X 50MM Bolt
10pcs
M6 X 45MM Bolt
8pcs 6MM Washer
28pcs 16MM Spacer 8pcs M6 Nut 10pcs
M5 X 13MM Screw
88pcs Wrench 1pc Allen Key 1pc
Outer Leg Cap
4pcs Inner Leg Cap
4pcs

Assembly Instructions
NOTE: We recommend that two adults work together to assemble this game.
Find a clean, level place to begin the assembly of your Table Tennis Table. The table will be
assembled upside down and then turned over on its legs once the assembly is completed.
Remove all the parts from the box and verify that you have all of the parts as shown on the
parts list above. Carefully cut or tear the four corners of the box so that the bottom of the box
can be used as your work surface.
Step 1
Place Table Surface-A (#1)
and Table Surface-B (#2)
with the painted surface
facing down on a flat
surface.
Connect Table Surfaces
together using three
Brackets
(#9) using twelve Screws
(#A7). See FIG. 1 and 1A.
Attach the Safety Strap -
Long (#13) and Safety
Strap - Short (#14) to the
surface using three
Screws
(#A1). See FIG. 1.
Assembly Tips:
Attention: If you are using an electric screwdriver in the assembly, please set at low torque
and do not over tighten the hardware. When assembling individual parts, loosely tighten
screws until all screws are inserted, then tighten completely.
Note: Center gap
tolerance
approximately 10~13mm.
Note: Align the
inside seams of
each sections so
that pre-drilled
holes line up
across from
each other.

Step 2
Place one Curved Outer Leg with Cap (#5) on the player end of the table half and one
Curved Inner Leg with Cap (#6) on the center end of the table half.
Attach the Leg Bracket (#19 & #20) to the Curved Outer Leg (#5) and the Curved Inner Leg
(#6) using Screws (#A7). See FIG. 2A.
Repeat the above steps for the other table half.
Note: Make sure that the
oval cut-out in the Leg
Bracket are facing the
center of the table for
proper installation.
This is hole for “Gravity
Lock” assembly.

Step 3
Attach one end of the Linkage Tube (#8) to the inside of the Curved Outer Leg (#5) using
one Bolt (#A2), two Washers (#A4), one Spacer (#A5) and one Nut (#A6). See FIG. 3A.
Repeat the same for the other end of this LinkageTube, only attaching it to the outside of
the Curved Inner Leg (#6).
Attach one end of the Linkage Tube with Stop Bracket (#7) to the inside of the Curved Outer
Leg (#5) using one Bolt (#A2), two Washers (#A4), one Spacer (#A5) and one Nut (#A6).
Repeat the same for the other end of this LinkageTube, only attaching it to the outside of
the Curved Inner Leg (#6). See FIG. 3B.
Repeat the above steps for the other table half.
Note: Be careful of the
assembly direction on
pictures when you
assemble the Linkage
Tube #7 and #8 in order
to fit the folding function.

Step 4
Place the Plastic Corner (#17) flush with table corner and attach using three Screws (#A1)
per Corner. See FIG. 4A.
Place the EndApron (#11) between the corners and flush with the table edge at the Player
end of table using six Screws (#A1) per EndApron. See FIG. 4.
Place the SideApron (#12) flush with table edge at the side of the table using five Screws
(#A1) per SideApron. See FIG. 4.
NOTE: Make sure the all Aprons are inside the Plastic Corners.

Step 5
Make sure the Outer Leg Caps (P1) and Inner Leg Caps (P2) are installed into the ends of
the leg. Then place the Wheel (#18) into the Legs. See FIG. 5.
With the logo upside-down, attach the Plastic Panel with Frame (#21) to the Curved Inner
Leg (#6) using two Bolts (#A3) and two Washers (#A4) per frame.
NOTE: Do not tighten securely at this time.

CAUTION: Two adults are recommended to flip the table as shown.
1.Lift the table off the ground.
2.Turn the table over, using caution to clear the legs as you turn.
3.Place the table on all four legs at the same time.
HOLD
TABLE CABINET DO NOT
HOLD THE
LEGS
DO NOT LEAN THE ON
the LEGS !

Step 6
Before turning the table over, make sure to push the Curved Inner Leg (#6) towards the
center of the table in order to fix leg in right position.
NOTE: Two adults are required to turn this table over.
One person should stand at each center of the table and turn the table over completely so
that it rests on its legs.
Standing at the sides of the table, place the two table halves so they are inches apart.
NOTE: Be careful that you do not push either half backwards as this may cause the
legs to fold!
Attach the Plastic Panel with Frame (#21) to the opposite table half using two Bolts (#A3)
and two Washers (#A4) per frame.See FIG. 7.
Now go back and tighten all the connections.
Note: Center gap
tolerance
approximately 10~13mm.

Step 7
Attach one Gravity Lock (#10) to the Curved Inner Leg (#6) using one Bolt (#A2), two
Washers (#A4), one “T” Washer (#22) and one Nut (#A6) per Gravity Lock. See FIG. 8A.
HARDWARE AFTER
ASSEMBLY

Step 8
Attach the Net Post (#16) at the middle of the table and slide the net over the post. Stretch
the Net (#15) across the center of the table and slip the net over the post on the opposite
side. See FIG. 9A.

Step 9
Engage the Wheels Lock.
Folding the table - First fold the side of the table without the Net Post. Hold the end securely
and lift the table. Make sure the Gravity Lock (#10) is locked. Repeat for the other side.
Attach the Safety Strap Long and short (#13, #14) together to prevent the sides from
falling. See FIG.10
To unfold the table - First release the Gravity Lock (#10) and Safety Strap (#13 & #14).
Then pull the bottom of the outer leg and slowly lower the table to the floor.
NOTE: When the table is in its storage position, always attach the safety strap
to prevent the sides from falling.
Safety Straps
Gravity Lock