Triumph Sports USA DOUBLE SHOT BASKETBALL STAND User manual

DOUBLE SHOT BASKETBALL STAND

Parts List
Board L Tube
2pcs
Board Tube
2pcs
Left Tube
1pc
Right Tube
1pc
Horizontal
Frame Brace
U Tube
1pc
Left Mounting
Tube
1pc
Support Tube
2pcs
Right Mounting
Tube
1pc
Ramp Tube
2pcs
Ramp L Tube
2pcs
Ramp U Tube
1pc
Horizontal Tube
2pc
Ramp Chute
1pc
Electronic Scorer
1pc
Mechanical
Scoring Arm
2pcs
Rim
2pcs
Rim Support
Plate
2pcs
Inflation Pump
With Needle
1pc
Net
2pcs
Backboard
1pc
M6 x 1mm Thick
Washer
4pcs
M6 x 20mm Bolt
16pcs
M6 x 50mm Bolt
6pcs
M6 x 60mm Bolt
4pcs
M6 x 70mm Bolt
4pcs
M6 Lock Nut
32pcs
Basketball
4pcs
3.5 x 10mm Bolt
4pcs
Electronic Scorer
Face Plate
1pc
Wrench
1pc
M6 x 92mm Bolt
2pcs
Locking Pin
2pcs
Mechanical Arm
Support Plate
2pcs
2pcs
M6 x 2mm Thick
Washer
(Pack inside
EScorer Box)
Allen Wrench
1pc
Plastic Pole
insert-A
2 pcs
8 pcs
PRE-INSTALLED PARTS
P1 P2
Plastic Pole
insert-B Spring Lock
8 pcs
P3

Assembly Instructions
Find a clean, level place to begin the assembly of your Basketball Game. We recommend that two adults work
together to assembly this basketball game.
Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.
STEP 1
WARNING:
1) Do not mix old and new batteries.
2) Do not mix alkaline, standard (carbon zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.
3) Do not dispose of batteries in fire, batteries may explode or leak.
Attach the Board Tubes (#2) to the Left Tube (#3) and
Right Tube (#4) using Spring Lock as shown in
FIGURE 1. 2
3 4
FIGURE 1
P2 P2
STEP 2
Attach the Support Tubes (#7)
to the Left Mounting Tube (#6)
and Right Mounting Tube (#8)
using Spring Lock as shown
in FIGURE 2.
7
6 8
FIGURE 2 NOTE:
Triangle Plate
face inside
P2 P2

STEP 3
Attach tube from assembly STEP 2 to tube
assembly STEP 1 using Bolts (#24) and
Lock Nuts (#27) as shown in FIGURE 3.
Do not tighten Bolts
on this step.
6 8
7
43
22
NOTE:
Triangle Plate
face inside
NOTE:
Triangle Plate
face inside
7
24
27
2
7
2
24 27
7
FIGURE 3
STEP 4
Attach Horizontal Frame Brace U-Tube (#5) to tubes from assembly STEP 3 using Bolts (#26) and Lock
Nuts (#27) as shown in FIGURE 4.
Attach Horizontal Tube (#12) to tubes (#2) using Bolts (#24) and Lock Nuts (#27) as shown in FIGURE 4.
Use Wrench (#31) and Allen Wrench (#36) to tighten all Bolts.
Tighten, but do not overtighten.
P1
P1
2
2
7
7
8
6
3
4
5
12
24
27
24
27
26
27
27
26
27
27
26
26
FIGURE 4
24
27
12
2
7

STEP 5
Insert Board L-Tubes (#1) into Board Tubes (#2) as shown in FIGURE 5.
Attach Ramp Tubes (#9) to Left Mounting Tube (#6) and Right Mounting Tube (#8) using Bolts (#32),
Washers (#22), Washers (#34), Locking Pins (#33) and Lock Nuts (#27) as shown in FIGURE 5.
Use Wrench (#31) and Allen Wrench (#36) to tighten Bolts.
Note: This is a pivot point. “Snug” tighten
Lock Nuts (#27) only. Make sure this assembly
pivots freely.
Attach Ramp L-Tubes (#10) to Ramp Tubes (#9) using
Spring Locks as shown in FIGURE 5.
FIGURE 5
10
10
9
9
8
6
2
2
1
1
39
P2
P2
P2
P2
STEP 6
Attach Rims (#17) and Rim Support
Plates (#18) to the Backboard (#21)
using Bolts (#23) and Lock Nuts (#27)
as shown in FIGURE 6.
Attach Mechanical Scoring Arms (#15)
and Mechanical Scoring Arm Support
Plates (#35) to the Backboard (#21)
using Bolts (#23) and Lock Nuts (#27)
as shown in FIGURE 6.
Use Wrench (#31) and Allen
Wrench (#36) tighten all Bolts. 15
17
18
35
21
23
27
FIGURE 6
NOTE:
Mechanical Scoring Arm (#15)
sensor plug must pass through
Backboard (#21) and Mechanical
Scoring Arm Support Plate (#35)

STEP 7
Attach Electronic Scorer Face Plate to the
Backboard (#21) and connect with Electronic
Scorer (#14) using Bolts (#29)
as shown in FIGURE 7.
Loop the Rim Net (#20) through the ram horns
on the Rims (#17) as shown in FIGURE 7.
FIGURE 7
14
29
20
30
21
STEP 8
Slide elastic straps and the sleeve of the Ramp Chute (#13) onto the Board L-Tube (#1) as shown
in FIGURE 8 and DETAIL A.
Slide the Ramp U-Tube (#11) into the front sleeve of the Ramp Chute (#13) as shown in FIGURE 8
and DETAIL B.
Attach the Front U-Tube (#11) to the Ramp L-Tube (#10) using Spring Lock as shown in FIGURE 8
and DETAIL C.
Elastic
Strap
Ramp Chute
Upper Sleeve
13
1
DETAIL A
FIGURE 8
13
DETAIL B
11
13
Ramp Chute
Front Sleeve
11
10
DETAIL C

STEP 9
Place Horizontal Tube (#12) over the lower / front sleeve of Ramp Chute (#13) and then attach it to the
Ramp U-Tube (#11) using Bolts (#24) and Lock Nuts (#27) as shown in FIGURE 9 and DETAIL D.
Use Wrench (#31) and Allen Wrench (#36) to tighten Bolts. Tighten, but do not overtighten.
With the help of another adult, Attach the Backboard (#21) assembly to the Board L-Tubes (#1) using
Bolts (#25), Washers (#22) and Lock Nuts (#27) as shown in FIGURE 9 and DETAIL E.
At the bottom hole of the backboard, bring the ramp up behind the Tube (#12), attach the ramp tabs of
Ramp Chute (#13) using Bolts (#25) and Lock Nuts (#27) as shown in FIGURE 9 and DETAIL F.
Use Wrench (#31) and Allen Wrench (#36) to tighten Bolts. Tighten, but do not overtighten.
1
FIGURE 9
DETAIL E
DETAIL D
DETAIL F
13
21
25 22
27
27
25
21 1
13
12
24
27
13
12
11
vuV vmm
STEP 10
Connect the Sensor Wire of Mechanical Scoring Arms (#15) to Electronic Scorer (#14) as shown in FIGURE 10.
Connect the Control Wire (#37) to Electronic Scorer (#14) as shown in FIGURE 10 and DETAIL G.
14
15
FIGURE 10
DETAIL G
Mechanical
Scoring Arm
Sensor
Mechanical
Scoring Arm
Sensor

ELECTRONIC SCORER OPERATION
Unscrew bolt using a screwdriver and open the battery box. Insert 3 AA batteries ( not included) in the order of
polarity as shown on the inside cover. Then close the cover using a screwdriver. Turn the power ON using the
ON/OFF switch. (if the game will not be used for a long period of the time, we recommend that the batteries
should be removed).
To fold the basketball game into the storage position, remove the Lock Pins (#33) from the
playing position on the Mounting Tubes (#6) &(#8). Lift the Front Horizontal Ramp Support
Tube (#11) until the game is in the storage position as shown in FIG. 12
vuVvmm
jvu{yvs
~pyl
}pzp{vy
Insert the Lock Pins (#33)
back into the Mounting
Tubes (#6) & (#8), locking
the basketball game into
the storage position.
33
FIGURE 12
Trouble Shooting:
Game won't turn on
1.Make sure switch on scorer is in the on position.
2.Make sure switch mechanical scoring arm wires are in the home and visitor slots on the scorer.
Game shuts off during play
1.Check the batteries. Make sure they are new batteries.
2.The batteries might be lose causing the game to shut off. Take off the battery cover on the scorer. Take
a piece of paper, fold it so it fits over the batteries. Put the battery cover back on. This should better
secure the batteries and prevent them from being moving in any way.