TROJAN PRO PRIAM STUDIO WORKSTATION User manual

PRIAM STUDIO WORKSTATION
Assembly Instructions

Components:
Z1
Z2
Z3
Z4
Z5
Z6
Z7
Z8
Z9
Z10
Z11
Z12
Z13
A
B
C
D
E
F
G
H
I
Tapping Screw (x24)
Bolt (x22)
Bolt (x6)
Nut (x6)
Eccentric Nut (x32)
Derrick Screw (x32 )
Dial Pad (x8)
Feet Pad (x2)
Support Bracket (x3)
TYPE-R (x32)
Dial Wheel (x2)
Rail (x2)
4U Rack Strips (x4)
Mid-Leg Support (x1）
Left-Leg Support (x1）
Right-Leg Support (x1）
Rear Brace Support (x1）
Work Surface (x1）
Upper Shelf (x1)
Junction Plate (x4)
Speaker Tray (x2）
Keyboard Tray (x1)
Assembly Instructions
Studiospares Europe Ltd. 19 Bilton Way, Luton LU1 1UU, UK
www.studiospares.com [email protected] [phone]

Components:
Z1
Z2
Z3
Z4
Z5
Z6
Z7
Z8
Z9
Z10
Z11
Z12
Z13
A
B
C
D
E
F
G
H
I
Tapping Screw (x24)
Bolt (x22)
Bolt (x6)
Nut (x6)
Eccentric Nut (x32)
Derrick Screw (x32 )
Dial Pad (x8)
Feet Pad (x2)
Support Bracket (x3)
TYPE-R (x32)
Dial Wheel (x2)
Rail (x2)
4U Rack Strips (x4)
Mid-Leg Support (x1）
Left-Leg Support (x1）
Right-Leg Support (x1）
Rear Brace Support (x1）
Work Surface (x1）
Upper Shelf (x1)
Junction Plate (x4)
Speaker Tray (x2）
Keyboard Tray (x1)
Assembly Instructions
Studiospares Europe Ltd. 19 Bilton Way, Luton LU1 1UU, UK
www.studiospares.com [email protected] [phone]

You will receive three boxes.
Contents of box 1
Contents of box 2

Contents of box 3
1) Screw 2 x Foot Pads (Z8) to
Mid-Leg Support (A).

2) Attach Rail (Z12) to Left-
Leg Support (B) using screws
(Z2). Repeat for the Right-Leg
Support.
First disassemble double-folded
rail by extending the rail, lifting
the latch and seperating the two
sections of the rail.

Then continue attaching the rail.

When installing this screw, you
may need to use a washer.
The washers are included with
the Priam in a small postage bag.
3) Then t Derrick screws (Z6) in
the appropriate holes.

4) Fit the Rear Support Brace (D)
using Derrick Screws (Z6)

5) Install Eccentric nuts (Z5) to
Read Support Brace (D)
6) Using the installed Derrick
Screws (Z6) and Eccentrc Nuts
(Z5) attach the Left and Right-
Leg Supports.

7) Attach Mid-Leg Support (A)
using Derrick Screws (Z6) and
Eccentric Nuts (Z5)

8) Fit both sides of Work Surface
(E) with Derrick Screws (Z6)

9) Attach Work Surface (E) to Leg
Supports.
10) Connect the two sets of 4U
Rack Strips (z13) to Junction
Plates (G) using Tapping Screws
(Z1).

11) Fit the Junction Plates (G)
with Eccentric Nuts (Z5) and
attach them to the Work Surface
(E).

12) Attach the Dial Pads (Z7)
using Tapping Screws (Z14), then
install Dial Wheel (Z11) using Bolt
(Z14).

13) Connect Speaker Tray (H)
using Bolt (Z2) in the upper holes
of the Upper Shelf.
It’s easiest to turn the shelf
upside down to do it this.
14) Add Derrick Screws (Z6) to
Upper Shelf (F).

15) Connect Upper Work Shelf (F)
to the Juncton Plates (G) using
Eccentric Nuts (Z5).
16) Attach the 3 x Support
Brackets (Z9) using Tapping
Screws (Z1).

17) Install Keyboard Tray (I) with
Rails (Z12) using Bolts (Z3) and
Nuts (Z4).

18) Fit Keyboard Tray into the
Priam Studio Workstation.