TRU Audio SB-SLIM-44P User manual

User Manual
SB-SLIM-44P
Contents:
(1) Soundbar
(1) Cloth-Wrapped Grill
(1) Wall Mount Bar
(2) Wall Mount Blocks with leveling screws
(8) Rubber Pads
(1) TruAudio Logo Badge
Description
The SB-SLIM-44P soundbar was designed to work great
with most flat or curved screen TV’s. Our patent-pending
wire pass-through design makes terminating the soundbar
a breeze. The thin-profile aluminum enclosure not only
provides the soundbar with a luxurious look and feel, but
also guarantees its durability. Because of the 3-channel
design they are perfect for a discrete 5.1 system. The
SB-SLIM-44P offers a modern design and innovative
mounting features.
Installation
The soundbar can be mounted using the included wall
mount bracket, or mounted directly to the TV using the
optional SB-CUSTOM-TVB mounting bracket.
Using the (included) Wall Mount
Mount the wall mount bar to the wall using appropriate
screws. Make sure the bar is installed level with the TV.
When installed, the top of the soundbar will sit
approximately 3/8” (10mm) higher than the top edge of the
wall mount bar. The bottom of the soundbar will be
approximately 5.75” (146mm) below the top edge of the
wall mount bar.
Place one wall mount block on either side of the bar,
making sure the set screw is centered in the block prior to
placing it on the bar. Each block should be placed in the
recess just to the outside of the mounting screw for that
side of the bar. The soundbar will rest on these blocks
when installed and a wider placement gives the soundbar
more stability. Placing the blocks too far from the
mounting screws may allow the bar to bend.
Place the soundbar on the wall mount, taking care to not
disturb the wall mount blocks. It may be necessary to level
the soundbar slightly if mounted very close to the TV. If so,
remove the soundbar from the mount and adjust the set
screws in the blocks. Screwing the set screw further into
the block will raise that side of the soundbar slightly.
slightly. You should only
adjust the set screw a
maximum of 1/16” (1.5mm),
and should never unscrew
the set screw, as that could
make the soundbar unstable
on the mount. Wall Mount Block
Set Screw
Wall Mount Block
Mounting Screw
Wall Mount Block
Wall Mount Bar
Mounting Screw

It is the policy of TRUAUDIO to continuously incorporate improvements into our products. All specifications are subject to
change without notice. If you have any questions regarding this or any other TRUAUDIO products, please visit
www.TruAudio.com or contact us:
Office: 1-888-858-1555, Monday-Friday 7 am - 6 pm MST.
Fax: [phone]
Email: [email protected]
TruAudio
198 N Old Highway 91
Hurricane, UT 84737 USA
Using the (optional) TV Mount
Refer to the instructions included with the
SB-CUSTOM-TVB when mounting the SB-SLIM-44P soundbar to a TV directly.
Wiring the Soundbar
The magnetized cover panel on the front of the soundbar hides a 6-conductor Phoenix connector. To wire the soundbar,
remove the cover panel and pass the speaker wires through to the front of the soundbar. Remove the unterminated Phoenix
connector and terminate the speaker wires according to the markings on the Phoenix connector, making sure to keep the
polarity and position correct for each channel. Be careful to avoid any loose strands that could cause a short between
conductors.
In order for these soundbars to perform to their full potential, we
recommend pairing them with a quality home theater receiver or
amplifier. For more information on installing or wiring the
soundbar please see the installation videos posted online at
truaudio.com.
Color:
Speaker Type:
Tweeter:
Woofer:
Passive Radiator:
Grill Type:
Power:
Sensitivity:
Freq Response:
Impedance:
Finish Dims:
Black
Low Profile Passive LCR Soundbar
(3) 1” Silk Soft Dome
(3) 4.5” Injected Polypropylene
(3) 4.5” Injected Polypropylene
Cloth/Aluminum
100W per channel RMS
88 dB
80Hz to 20kHz
8 ohm
6.14” (156mm) H,
2.44” (62mm) D,
44.0” (1118mm)
SB-SLIM-44P
SoundVision Technologies dba TRUAUDIO
SPEAKER PRODUCT WARRANTY
All in-ceiling, in-wall, in-room speakers and volume controls have a limited lifetime warranty. This warranty includes lifetime parts
and repair labor on all components. The warranty extends only to the original purchaser of the product and not to any subsequent
owner. TRUAUDIO’s obligation under these warranties is limited to repairing or replacing any component found defective in
material or workmanship under normal conditions of use with an equal and/or current product. These warranties shall not apply to
products which have been abused, modified, or disassembled. Products to be repaired or returned under this warranty must be
returned to the factory through an authorized TruAudio dealer with all transportation and insurance charges prepaid.