Truck System Technologies 507 FT User manual

!!"#$%&'()*+,&!+$-./0/12+)&
770.889.9102
>43 ?! @?0/A5*-"/#1-B =.C >43 @D=:B
E#2$% F.)*=00=*2/. G#2C+
HIJJKFLG 'ML'NJ' !N !FJM ON'F!FNL'
1. Take Sensors out of package and decide which tires the sensors will be placed on.
Use number labels from kit and mark each sensor according to tire position. Use the
T1, T2, etc. numbers for a trailer or towed unit.
2. Turn monitor on. O"+)) =.C -/0C *-+ DNPM Q#**/. until it beeps, about 6 seconds.
(This will put you in the coding mode.)
3. Using the + and/or – button, ,/R+ $#")/" */ *-+ S2")* *2"+ :/)2*2/. you want to
add a sensor to.
4. T/0C *-+ )+.)/" for that tire position directly and quickly
:"+)) =.C "+0+=)+ *-+ DNPM Q#**/.
#.C+" *-+ ,/.2*/"
.(You will hear a short beep.)
5. Use the + and/or – button to ,/R+ */ *-+ .+U* *2"+ :/)2*2/. you want to add a
sensor to. Get the next sensor in your series and code it.
6. JMOMI! steps 4 and 5 until all of the tire sensors have been married to their correct
tire positions.
7. O"+)) =.C "+0+=)+ *-+ HNPM Q#**/.. (This will bring you to the standby screen
and you will see only the tire positions you have set.)
NOTE: If#the#front#right#tire#already#has#a#code!(instead!of!fff!fff,!indicating!there!is!
no sensor in that position), you can remove that code by pressing and holding the SET
button until it beeps. Now you can add a new sensor to that position. (The factory uses
this position to test the monitor and sometimes does not remove it.)
OJNGJIHHFLG TFGT ILP VN< OJM''WJM ILP TFGT !MHOMJI!WJM IVIJH'
1. O"+)) =.C -/0C *-+ HNPM Q#**/. until it beeps (approximately 6 seconds). You
should see PSI as the unit of measure on the screen.
TST-Doc-507-QI-(B)

2. O"+))&=.C&"+0+=)+&*-+&HNPM&Q#**/..!You!will!see!either!“F”!for!Fahrenheit,!or!“C”
for!Celsius.!Press!the!+!(plus)!button!to!change!to!the!unit!of!measure!you!want.
3. Press!and!release!the!MODE!button.!The!first!set!of!axles!will!be!flashing!along!with
the!high_pressure!icon.!W)2.1&*-+&HNPM&Q#**/.X&:"+))&=.C&"+0+=)+&#.*20&(/#&="+
/.&*-+&)+*&/S&=U0+)&(/#&A2)-&*/&:"/1"=,Y
NOTE: Set#the!high3pressure#alarm!using!the!–!(minus)!button!to!20%#
above!normal!operating!tire!pressure.!(The!default!high!pressure!is!175).
4. Press and Release the MODE button. The same set of axles will be flashing along
with the low_pressure icon. (The default low pressure is 100.)
NOTE: Set the low3pressure alarm using the – (minus) button at 10% below
normal operating tire pressure.
Example:Your normal tire pressure is 100 lbs. Set the high_pressure alarm to 120
lbs. and the low_pressure alarm to 90 lbs.
NOTE: IF THE NORMAL TIRE PRESSURE IS LOWER THAN 100 PSI,YOU MUST FIRST
SET THE LOW PRESSURE ALARMS. THEN, USING THE MODE BUTTON, SCROLL
THROUGH ALL AXLES AND BACK TO THE AXLES YOU ARE USING. NOW YOU CAN SET
THE HIGH PRESSURE ALARM FOR EACH AXLE.
5. When you reach the *"=20+"&)+$*2/. of the monitor, all of the axles/tires will be
flashing. '+*&*-+&-21-&=.C&0/A5:"+))#"+&=0=",)&=)&=Q/R+ for all of these axles at
one time, as a group.
6. O"+))&=.C&"+0+=)+&*-+&HNPM&Q#**/..You will see the default temperature of 158º.
This is the last setting. We recommend leaving the high temperature alarm here.
7. ?FLIV&'!MO; O"+))&=.C&"+0+=)+&*-+&'M!&Q#**/. to save all parameters. You will
hear a beep. The screen will change to the standby mode for normal operation.
You can now screw the sensors on the valve stems on the correct tire
positions and the monitor screen will display the current temperature
and pressures of your tires. The initial readings may take up to ½ hr. to
display. After the first time, the sensors should read after a few minutes.
TST-Doc-507-QI-(B)
<=""=.*(; 3years
More Info