Trusted Clean TPL-17-200-CE-HEAT-TCP User manual
GALAXY
OWNER’S MANUAL &
PARTS LIST
This equipment is intended for commercial use only.
TPL-17-200-CE-HEAT-TCP
BEFORE OPERATING THE MACHINE
Read the manual carefully and completely before attempting to operate the unit.This manual has important
information for the use and safe operation of the machine. Keep this manual handy at all times.This machine
will assure years of satisfactory service if operated and maintained according to recommendations in this
manual.If additional information is needed, please contact your local distributor or write to:
CleanFreak
P.O. Box 569
Wausau, WI 54402
WARNING
• Themachinewasdesignedforuseoncarpet,oorandupholsteryextractionapplicationsasper
instructions and recommendations written in this manual.Any deviation from its proper use or
purpose and the consequential damage that may occur is the sole responsibility if the end user.
• Disconnectthepowercordfromtheoutletbeforeservicing.Donotleavemachineconnectedtoan
electrical outlet when unattended.
• Donotimmerseorusethismachineinstandingwater.Suchusemaycauseelectricshock.
• Thisequipmentisnotdesignedtohandleorusecombustible/volatilesubstancessuchasgasolineor
kerosene,in,on,ornearthemachine.Theuseofsuchmaterialswillcauseextremehazardous
condition.
• Whenusinganextensioncord,useonlya3-prongconductorgroundingcord,12gaugewireorheavier.
• To avoidelectricshock,donotexposetheunittorain.Storeitindoorsonly.
• Donotusethemachinefordryvacuuming.
• Usedefoameratalltimestopreventdamagetothevacuummotor(s).
• Donotusewaterinexcessof170ºF(76ºC).
• To preventsealdamageandchemicalbuild-uptothepumpsystem,runcleanwaterthroughthe
solution lines after each day’s use.
• Useonlycommerciallyavailablecarpetcleaningsolutionsanddefoamerintendedforusewith
machines of this type.Do not use dyes, bleaches, ammonia, or other additives.The use of powdered
cleaning solution if not diluted properly may result in damage to the pump. If powdered chemicals are
used,premixinaseparatecontainerbeforeplacinginthesolutiontank.
• Donotexposemachinetofreezingtemperatures.
• AllrepairsmustbedonebyanauthorizedCleanFreakrepairstation.
• Donotusereplacementpartsotherthanthosespeciedonthepartslist.
For units with HEAT’N’RUN heater:
• ReadandunderstandtheHEAT’N’RUNownersmanualbeforeusingtheHEAT’N’RUNheateronyour
GALAXYExtractor.
• Donotrunheaterd r y.
• Waterhookupsmustbeinplaceandwaterowingthroughtheheaterpriortoturningiton.Failuretodo
so may cause internal component damage and will void warranty.
• Heatermustbelledwithwaterorwaterbasedsolutionsatalltimeswheninuse.Tu r n offtheswitchand
unplug the heater from outlet when not in use.
• Donotuseheaterwith any other machine and at any pressure higher than 250PSI.
• Donotimmerseheaterinwater.
• To avoidexplosionand /orre,donotusesolventsoranyammableliquidinheater.
FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS WILL VOID THE
WARRANTY
GALAXY 2000FX-HR (BASE) PARTS LIST
ITEM # PART
#
DESCRIPTION QT
Y
1C00297 #8 X .25 PAN HEAD 1
2J11863 HOSE, 3 IN 1
3J00639 SCREW CLAMP, 1.63-2.43 IN 3
4J00618 VACUUM HOSE, 2 IN GRAY, WIRE, 22 IN LG 1
5C00273 LOCKNUT, 1-4 X 20, NYLON, SS 16
6F11178-BLK INTERCOOLER, GALAXY, BLACK 1
7C00233 WASHER, FLAT, .25 IN 26
8F00449 GROMMET 6
9C00284 SCREW, 10-32 X .375 GROUND 2
10 B11150 GROUND WIRE, GALAXY 2
11 G02522L VACUUM, 135 IN 115 V 5.7 IN 2
12 J00657 HOSE CLAMP, 2 IN SLDPRT 1
13 J00618 VACUUM HOSE, 2 IN GRAY, WIRE, 4 IN LG 1
14 C00261 NUT, .25-20 HEX 10
15 C00254 LOCK WASHER, 1-4 IN SPLIT 1
16 D11134 VAC PLATE 1
17 C11189 SCREW, 1-4 X 20 X 4.5 IN HEX 5
18 C02312 LOCK WASHER, .25 IN., INTERNAL STAR 1
19 C11516 SCREW, 1-4 X 20 X 4.5 IN, FLAT HEAD, PHILIPS 1
20 J11154 SOLUTION HOSE, .375, 100PSI, WIRE, 31 IN. LG 1
21 J11508 SCREW CLAMP #6, .43 TO .875 IN 8
22 G11904 POWER PRIME 1
23 A00060 .25 MALE X .375 BARB, BRASS 1
24 A00053 45 ELBOW, .25MP X .25FP 1
25 G03523-1 VALVE, REGULATOR, 200PSI 1
26 A00052 90 ELBOW, .25MP X .25FP 3
27 00580-13IN-MF-A HOSE ASSEMBLY, 13 IN X .25 HP 1
28 G00516-3 GAUGE, 0-600 PSI 1
29 C11244 WASHER, .56 X 1.5 X .05 4
30 A00104 QD, 1-4 M X 1-4 FP, BRASS 1
31 A00161 TEE, .25 FP, BRASS 1
32 A00111 NIPPLE, .25 IN 2
33 C00232 WASHER, .5IN, FLAT 1
34 A00154 90 ELBOW, .25NPT X .25 NPT 1
35 C11440 SPACER, HEATER MOUNTING PLATE 4
36 K10510 PLUG, 1.25 IN, BLACK 1
37 C02322 HEX BOLT, 1-4 X 20 X 1.75 IN 4
38 D010379 HEATER MOUNTING PLATE 1
39 C11165 SCREW, #8 X 1 IN, PAN, BLACK 5
40 F11790 HEATER, TUNNEL COVER, BLUE GRANITE 1
41 B11779 STAUB, 12-3 SJTW YELLOW 2
42 B00191 NYLON TIE, 11 IN BLACK 4
43 C00293 #8 X .5 IN PAN, BLACK SMS, PHILIPS 2
44 B00192 TIE HOLDER WITH GLUE 1
45 B11606 STRAIN RELIEF, PIGTAIL 2
46 H03545 COVER, SERIAL # LABEL 1
47 H00565-5 LABEL, SERIAL NUMBER 1
48 C02305 CAP NUT, .5IN PUSH-ON 2
49 C00240 WASHER, SHOULDER, NYLON 4
50 G11767 WHEEL, 10 IN 2
51 D11170 AXLE 1
52 F11789 BASE 1
53 C00314-1 HEX BOLT, 1-4 X 20 X 1 IN 8
54 G03518 CASTER, 4 IN 2
55 G13102 PUMP, 500 PSI, 120V 1
56 B00177 TERMINAL LUG, FEMALE, QD, .25 X .032, 16-14 AWG, FULLY INSULATED 2
57 C03251 WASHER, .187 ID, BACKUP 1
58 A00168 BUSHING.375 M X .25 P BRASS 4
59 A90004 .50 BARB X .25 MP, BRASS 1
60 A00155 MALE PLUG, .25 IN, NYLON 1
61 J11933 HOSE, .5 IN POLYWIRE PVC, 33 IN LG 1
62 J00632 PULSE HOSE, PUMP-QD, 42 IN 2
63 B00190 NYLON TIE, 4 IN 13
64 D13103 PLATE, PUMP, GALAXY, FLAT 1
65 H02564-2 LABEL, CAUTION, MOTOR HOUSING 1
66 J11933 HOSE, .5 IN POLYWIRE, 30 IN 1
67 K11935 STRAINER, INLINE, 5 IN 1
68 J11154 SOLUTION HOSE, .375, 100 PSI, WIRE, 27 IN LG 1
69 J00618 VACUUM HOSE, 2 IN GRAY, WIRE, 7 IN LG 1
70 E11169 GASKET, VAC MOTOR, GALAXY 2
71 B00179-2 CLOSED END CNTR, 16-3 6
GROUNDING INSTRUCTIONS
The 120VA/Candthe220VA/Cmodelshavebeenoutttedwiththeappropriate
grounded connectors. Make sure the machine is connected to a grounded outlet
havingthesamecongurationasthegroundedplug.Noadaptershouldbeusedwith
thismachine.Anymodicationtotheconnectorswillvoidthewarranty.
PREPARING THE MACHINE (ALL GALAXY EQUIPMENT)
IMPORTANT:ForallGalaxyequipment,useonlythecorrecthighpressure,highheatwands&uphol-
sterytools.Theyaredesignedtodeliverandmaintainthecorrectgallonsperminute(GPM),pressure(PSI)
andheatwhenattachedtotheGALAXYpumpsystem.Useofothermanufacturerwandscancauseover-
wettingofcarpet,damagetothepumpsystem(includinghose&ttings),lackofpressureandheat.
1. Pourcleansolutionintothesolutiontank.
2. Slidevacuumhoseontotheblackhoseadapter(locatedatthebackofthemachine)andthewandor
upholstery tool.
3. Connect the male end of the solution hose to the wand and the female end to the machine by sliding
knurledcollaronthefemalequickdisconnectttingback.Pushthemalettinginandreleasetheknurled
collar until it snaps back.
4. Make sure the drain valve is closed by pushing theT-handle all the way in.
5. Previouslyshampooedcarpetsusuallyhaveaheavybuild-upofoldshampooresiduewhichcancause
the vacuum system to ingest foam and result in damage to the vacuum motor. Remember to add recom-
mendedamountofdefoamertotherecoverytankeverytimeyoullthesolutiontank.
6. IfaPowermateistobeusedwiththemachine,connectthemaleplugonthewandtotheoptional
receptacle on the machine.
Additional Instructions for GALAXY’s with HEAT’N’RUN installed:
1. Besuretollthesolutiontankwithwaterbeforeplugginginthemachine.
2. Waterhookupsmustbeinplaceandwaterowingthroughtheheaterpriortoturningiton.Failuretodo
so may cause internal component damage and will void the warranty.
3. Spraywaterthroughthetool/wandbeforeturningontheheatertoassurethatthereiswaterow.
4. Heatermustbelledwithwaterorwaterbasedsolutionsatalltimeswhen inuse.
5. Plugheaterpowercordandmachinepowercordintoseparateoutletsonseparatecircuits.
6. Turn off the switch and unplug the heater from outlet when not in use.
7. Donotuseheaterwith any other machine than this adjustable PSI Galaxy.
8. Turn on heater switch when you are ready to clean.
CAUTION:Whenthegreenlightontheheaterison,theheaterisheating.Whenthegreenlightisoff,the
water in the heater tank is up to temperature and the thermostat switch in the heater has turned the heater
off. It will automatically turn on again when the water temperature in the heater has cooled.
DELIVER MAXIMUM HEAT by performing the following SYSTEM WARM-UP PROCEDURES at the start of
each day:
1. Attach the solution hose to the quick disconnect on the machine.
2. Attachthewarm-upquickdisconnectwithspraytipattachedtotheotherendofthesolutionhose.
3. Placewarm-upquickdisconnectinthesolutiontank.
4. Fillsolutiontankwithcleaningsolution.
5. Turn on pump.
6. Whenwaterisowingoutofthewarm-upquickdisconnect,turnontheheater.
7. Let the pump and heater run for 4 to 5 minutes.
8. Remove warm-up quick disconnect.Attach the wand or upholstery tool and begin cleaning.
1
2
36
4
5
7
8
9
10
11
12
13
14 15 16
18
19
17
20 22
34
26
27
24
28
29
26
21
23 25
32 31 30
37 38
3536
40
41
39
4243
44
46
47
45
5152 50 4849
53
7
54
55
10
58
59
21
60
42 64 65 66 67
5
69
71
3
70
7
7
49
21
17
2000FX-HR Base
12-19-07
2000FX-HR Base
12-19-07
62
5657
39
68
61
33
29
63
21
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
C00297 #8 X .25 Pan Head
1
2
J11863 Hose, 3 in
1
3
J00639 Screw Clamp, 1.63 - 2.43in.
3
4
J00618 Vacuum Hose, 2in Grey, Wire, 22 in lg
1
5
C00273 Locknut, 1-4 X 20, Nylon, SS
16
6
F11178-BLK Intercooler, Galaxy, Black
1
7
C00233 Washer, Flat, .25 in
26
8
E00449 Grommet
6
9
C00284 Screw, 10-32 X .375 Ground
2
10
B11150 Ground Wire, Galaxy
2
11
G02522L Vacuum , 135 in, 115 V, 5.7 in
2
12
J00657 Hose Clamp, 2 inSLDPRT
1
13
J00618 Vacuum Hose, 2 in Grey, Wire, 4 in lg
1
14
C00261 Nut, .25-20, Hex
10
15
C00254 Lock Washer, 1-4in Split
1
16
D11134 Vac Plate
1
17
C11189 Screw, 1-4 X 20 X 4.5 in, Hex
5
18
C02312 Lockwasher, .25 in., Internal Star
1
19
C11516 Screw, 1-4 X 20 X 4.5 in, Flat Head, Phillips
1
20
J11154 Solution Hose, .375, 100PSI, Wire, 31 in lg
1
21
J11508 Screw Clamp #6, .43 to .875 in
8
22
G11904 Power Prime
1
23
A00060 .25 Male X .375 Barb, Brass
1
24
A00053 45 Elbow, .25MP X .25 FP
1
25
G03523-1 Valve, Regulator, 200 PSI
1
26
A00052 90 Elbow, .25MP X .25FP
3
27
00580-13in-MF-A Hose Asm, 13 in X .25HP
1
28
G00516-3 Gauge, 0-600PSI
1
29
C11244 Washer, .56 X 1.5 X .05
4
30
A00104 QD, 1-4 M X 1-4 FP, Brass
1
31
A00161 Tee, .25 FP, Brass
1
32
A00111 Nipple, .25 in
2
33
C00232 Washer, .5 in, Flat
1
34
A00154 90 Elbow, .25 NPT X .25 NPT
1
35
C11440 Spacer, Heater Mounting Plate
4
36
K10510 Plug, 1.25 in, Black
1
37
C02322 Hex Bolt,1-4 X 20 X 1.75 in
4
38
D010379 Heater Mounting Plate
1
39
C11165, Screw, #8 X 1 in, Pan, Black
5
40
F11790 Heater, Tunnel Cover, Blue Granite
1
41
B11779 Stub, 12-3 SJTW Yellow
2
42
B00191 Nylon Tie, 11in Black
4
43
C00293 #8 X .5in Pan, Black SMS, Phillips
2
44
B00192 Tie Holder with Glue
1
45
B11606 Strain Relief, Pigtail
2
46
H03545 Cover, Serial # Label
1
47
H00565-5 Label, Serial Number
1
48
C02305 Cap Nut, .5in Push-on
2
49
C00240 Washer, Shoulder, Nylon
4
50
G11767 Wheel, 10 in
2
51
D11170 Axle
1
52
F11789 Base
1
53
C00314-1 Hex Bolt, 1-4 X 20 X 1in
8
54
G03518 Caster, 4 in
2
55
G13102 Pump, 500 PSI, 120 V
1
56
B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated
2
57
C03251 Washer, .187 ID, Backup
1
58
A00168 Bushing .375 M X .25 F Brass
4
59
A90004 .50 Barb X .25 MP, Brass
1
60
A00155 Male Plug, .25 in, Nylon
1
61
J11933 Hose, .5 in Polywire PVC, 33 in lg
1
62
J00632 Pulse Hose, Pump - QD, 42 in
2
63
B00190 Nylon Tie, 4in
13
64
D13103 Plate, Pump, Galaxy, Flat
1
65
H02564-2 Label, Caution, Motor Housing
1
66
J11933 Hose, .5 in Polywire, 30 in
1
67
K11935 Strainer, Inline, .5 in
1
68
J11154 Solution Hose, .375, 100PSI, Wire, 27 in lg
1
69
J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg
1
70
E11169 Gasket, Vac Motor, Galaxy
2
71
B00179-2 Closed End Cntr, 16-3
6
Additional instructions:
Primethepumpbyconnectingthepump priming hose,whichisthe4footlongsolutionhosewithastopper
on one end, and a quick disconnect on the other end. Attach the quick disconnect to the machine, and the
stopper to the vacuum hose. Make sure your solution tank is full of solution to create additional pressure.
Turn on the pump, then the vacuum motors to create suction and draw water through the air locked pump.
When the solution steadily flows through the solution line, your pump is primed.
Thepumpshould rarelyever needtobeprimed.Ifthesolutiontankisallowedtorunlow, it will result in the
pump sucking in air, then the pump will need to be primed. Erratic pressure fluctuation indicates air in the
lines and means the pump needs priming as well.
OPERATING INSTRUCTIONS- CARPET TOOL
1. Turnonthevacuumandsolutionswitches.Slowlypullthetooltowardsyouwith
the solution valve trigger engaged. Then make a pass forward and backward
withthevacuumonly(nospray)overthecleanedareatoremoveasmuchdirt
and solution as possible. Do not overwet carpet! Make overlapping passes to
prevent streaking.
2. Ifthecarpetisheavilysoiled,squeezesolutionvalveontheforwardpassas
well as backwards, allowing cleaning solution a few seconds longer to work prior
to vacuuming. Another method is to raise the wand 8” above the carpet and
pre-spraylightlypriortocleaningpasses.Onextremelysoiledcarpets,we
recommend using a pre-spray solution.
3. Whenyourunoutofsolution,turnoffthepump.Attachthedrainelbowonthe
drainvalve.Placea pailunderthedownspoutandpullupthedrainvalveT-handle.
Dirty solution will pour out until the tank is empty. Close the drain valve. Use a clean
bucketwhenyourellthesolutiontank.
4. Whenthejobiscompleted,turntheswitchoffanddisconnectthevacuumandsolution
hoses from the carpet and the machine. Drain the recovery tank through the drain valve as
before.
GALAXY 2000FX-HR (UPPER) PARTS LIST
ITEM # PART # DESCRIPTION QT
Y
1F11787 SOLUTION TANK 1
2F11792 RECOVERY TANK 1
3F11791 LID, SOLUTION TANK 1
4A00060 3-8 BARB X 1-4MP, BRASS 2
5A00052 90 ELBOW, .25MP X .25FP 3
6C11244 WASHER, .56 X 1.5 X .05 3
700580-16.5IN-PH-A HOSE ASSEMBLY, 16.5 IN X .25 IN 1
8E11124 GASKET, RECOVERY TANK 1
912904A STAND PIP ASSEMBLY 1
AK11965 ELBOW, 180º FLOAT BALL 1
BK00675 PVC PIPE, 1.5 X 12 IN, SCH 40 WHITE 1
C
K00741 ADAPTER 1
D10989-2A FLOAT BALL SCREEN 1
10 F11785 LID RECOVERY TANK 1
11 C12039 WASHER, 1-4 X 1, SS 2
12 C02322 1-4 X 20 BOLT 2
13 B11769 EXTENSION CORD, 12-3 SJTW 2
14 C11177 VELCRO STRAP 2
15 H02548-2 LABEL, IMPORTANT, CORD 2
16 B00185-30 WIRES, 73 IN 2
17 B00185-40 WIRES, 73 IN 2
18 B010314 WIRE HARNESS 1
19 F11786 HANDLE 1
20 B00177 TERMINAL LUG, FEMALE, QD, .25 X .032, 16-14 AWG, FULLY INSULATED4
21 B00185-40 WIRE, 14 GA, BLACK, UL1015, 10 IN 1
22 C00295-1 #10 X .75 PAN, BLACK SMS, PHILIPS 2
23 C00293 #8 X .5 IN PAN, BLACK, SMS, PHILIPS 2
24 D11168 COVER, SWITCHPLATE 1
25 B02211-1 SWITCH, ROCKER, GREEN LIGHT 3
26 D010284 SWITCHPLATE 1
27 E010453 GASKET, SWITCHPLATE 1
28 B00177-1 TERMINAL LUG, FEMALE, QD, .25 X .032 2
29 B00185-30 WIRE, 14 GA, WHITE, UL1015, 10IN 1
30 C02315 LOCKWASHER 2
31 C00264 NUT, 10-32 1
32 C11141 SCREW, ALLEN HEAD, 10-24 X 1.25 IN 8
33 K00665-1 HOSE ADAPTER, 1.5 ON, BLACK 1
34 E11128 GASKET, DRAIN VALVE 2
35 C00313 HEX BOLT, 1-4 X .5SS 6
36 C00233 WASHER, FLAT, .25 IN 8
37 C02312 LOCKWASHER, .25 IN., INTERNAL STAR 2
38 D010283 PLATE, HEATER MOUNTING 1
39 F11804 HEATER MOUNT 1
40 C00261 NUT, .25-20, HEX 2
41 K00710 ELBOW, DRAIN VALVE, BLACK 1
42 K00711 DRAIN VALVE, BLACK 1
43 C00254 LOCK WASHER, 1-4 IN SPLIT 2
44 C02294 SCREW, 1-4 20 X 1.25 2
45 K11185 ELBOW, 90, 1.5 IN, MT-MS, PVC 1
46 K00672-1 PVC PIP, 1.5 X 2.25 IN, SCH 40 WHITE 1
47 E11129 GASKET, 5 FT, LONG 1
48 A90004 .50 BARB X .25 MP, BRASS 1
49 D00373 INLET FILTER, .25 NPT 2
50 A00124 HEX NUT NPT, BRASS 2
51 C11143 SCREW, 1-4 20 X 1.25 IN, SS PAN HEAD, PHILIP 2
52 S11179 NON-SKID TAPE, 1 IN. ROLL 1
POWERMATE 1204ACH
IMPORTANT: 1204ACHisforusewithall heated Galaxy extractors.
1. Connect the cord on the power wand to the optional receptacle in back of the machine.
Turn on the vacuum and pump switches.
2. Themotorforthepowerbrushisturnedonandoffbyalightedrockerswitch
locatedonthetopofthebase.Solutionapplicationiscontrolledbysqueezing
the solution valve lever.
3. To move the power wand forwards, push the wand handle downward, raise
the front end and push the wand into position using the rear wheels. To pre-
spray,squeezesolutionvalveleverwhilemovingwandforwardandbackwards
over the area to be pre-sprayed.
4. To clean, lift the wand handle to insure the nose of the wand is against the
carpet,thenwhilesqueezingthesolutionvalvelever,pullthewandtowards
you.
Here’s how it works-thesolutionisjetsprayeddeepintothecarpet
toloosenthedirt.Thebrushscrubstheberandbreaksupsurface
anddeepdirt.Ituffsthenapwithoutdistortiontothepile.Withthe
weight of the base on the suction head, the vacuum picks up the dirt
and solution. Make overlapping passes to prevent streaking.
5. Gooverthepathyoujustcleanerwithoutsqueezingthesolutionvalveleverto
remove as much dirt and solution as possible.
POWERMATE 1800AC-200
IMPORTANT:1800AC-200isforusewithall heated Galaxy extractors.
1. Connect the cord on the power wand to the optional receptacle in the back of the machine. Turn on the
vacuum and pump switches.
2. Themotoroftherotatingpowerbrushisoperatedwithyourrighthandcontrollingalongtoggleswitch.
Pullitupformomentaryuse,pushitdownforcontinuousbrushaction(centeroff).Solutionapplicationis
controlledbydepressingtheowswitchleverwithyourrighthandngertips.
3 . To adjustthehandleintooperatingposition,pullupthegriponthelockingleverlocatednearthebaseof
the handle. Move the handle to waist level height and push down grip handle on lever to lock into place.
4. To move the power wand forward, push handle downward to raise the front end and move the wand into
position.To pre-spray,depresstheowswitchlever(solutioncontrol)while
moving wand forwards or backward over the area to be cleaned with the front
end raised.
5 . To clean,depressthesolutionowleverwhilepullingthepowerwandtowardsyou.
Here’s how it works-thesolutionisjetsprayeddeepintothecarpet
toloosendirt.Therotatingbrushscrubstheberandbreaksupsurface
anddeeprooteddirt.Ituffsthenapwithoutanydistortiontothepile
Withtheweightofthebaseonthesuctionhead,thevacuumpicksup
the dirt and solution. Make overlapping passes to prevent streaking.
6. Makeapassoverthepathyoujustcleanedwithoutdepressingthesolutionow
lever(vacuumonly)andwiththebrush
still on to remove as much dirt and solution
as possible.
14 15
13
11
12
10
3
1
2
7
6 54
17 1816 2019 21
27
24
26
22 23
25
28
29
30
31
32
33
34
35
38
39
40
41
42
34
43
44
45
46
47
47
48
5 49
51
52
37
36
8
2000FX-HR
Upper
1-26-08
2000FX-HR
Upper
1-26-08
36
6
4
50
9B
9A
9A
9C
9D
9
9A
9B
9C
9D
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
F11787 Solution Tank
1
2
F11792 Recovery Tank
1
3
F11791 Lid, Solution Tank
1
4
A00060 3-8 Barb X 1-4MP, Brass
2
5
A00052 90 Elbow, .25MP X .25FP
3
6
C11244 Washer, .56 X 1.5 X .05
3
7
00580-16.5 in-PH-A Hose Asm, 16.5 in X .25 in
1
8
E11124 Gasket, Recovery Tank
1
9
12904A Stand Pipe Assembly
1
K11965 Elbow, 180 Deg. Float Ball
1
K00672 Pvc Pipe, 1.5 X 12 in, Sch 40 Wht
1
K00741 Adapter
1
10989-2A Float Ball Screen
1
10
F11785 Lid, Recovery Tank
1
11
C12039 Washer, 1-4 X 1, SS
2
12
C02322 1-4 X 20 Bolt
2
13
B11769 Extension Cord, 12-3 SJTW
2
14
C11177 Velcro Strap
2
15
H02548-2 Label, Important, Cord
2
16
B00185-30 Wires, 73 in
2
17
B00185-40 Wires, 73 in
2
18
B010314 Wire Harness
1
19
F11786 Handle
1
20
B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated
4
21
B00185-40 Wire,14 GA Black, UL1015, 10 in
1
22
C00295-1 #10 X .75in Pan, Black SMS, Phillips
2
23
C00293 #8 X .5in Pan, Black SMS, Phillips
2
24
D11168 Cover, Switchplate
1
25
B02211-1 Switch, Rocker, Green Light
3
26
D010284 Switchplate
1
27
E010453 Gasket, Switchplate
1
28
B00177-1 Terminal Lug, Female, QD, .25 X .032
2
29
B00185-30 Wire,14 GA White, UL1015, 10 in
1
30
C02315 Lockwasher, #10 Int. Str, SS
2
31
C00264 Nut, 10-32
1
32
C11141 Screw, Allen Head, 10-24 X 1.25 in
8
33
K00665-1 Hose Adapter, 1.5in, Black
1
34
E11128 Gasket, Drain Valve
2
35
C00313 Hex Bolt, 1-4 X 20 X .5 SS
6
36
C00233 Washer, Flat, .25 in
8
37
C02312 Lockwasher, .25 in., Internal Star
2
38
D010283 Plate, Heater Mounting
1
39
F11804 Heater Mount
1
40
C00261 Nut, .25-20, Hex
2
41
K00710 Elbow, Drain Valve, Black
1
42
K00711 Drain Valve, Black
1
43
C00254 Lock Washer, 1-4in Split
2
44
C02294 Screw, 1-4 20 X 1.25
2
45
K11185 Elbow, 90, 1.5 in, MT-MS, PVC
1
46
K00672-1 Pvc Pipe, 1.5 X 2.25 in, Sch 40 Wht
1
47
E11129 Gasket, 5 ft. Long
1
48
A90004 .50 Barb X .25 MP, Brass
1
49
D00373 Inlet Filter, .25 NPT
2
50
A00124 Hex Nut, .25 NPT Brass
2
51
C11143 Screw, 1-4 20 X 1.5 in, SS Pan Head, Phillips
2
52
S11179 Non-Skid Tape, 1 in. Roll
1
CLEANING UPHOLSTERY
Cleaning upholstery with success requires a good knowledge of the type of fabric you will work on. Look for
the cleaning instructions label sewn on the underside of the furniture for the recommended method of clean-
ing.Ifitcallsfordrycleaning,donotattempttocleanbywetextractionotherwisedamagetothefabriccould
occur.Extractionworksperfectlyonmostsyntheticfabricsincludingsyntheticvelvets.
Before proceeding, test the fabric for colourfastness. Apply a small amount of cleaning solution on the fab-
ricinaninconspicuousspot.Wait2to3minutesandrubtheareawithawhiteterryclothtowel.Ifnocolor
comes off the towel, the fabric should be safe to clean. If a little color comes off, there is some risk of colors
runningwhenyouclean.Itmaybepossibletostabilizecolorsbycleaningwithanacidicrinse.
1. Preparethemachineinthesamemannerasforcarpetcleaning(seePreparingtheMachine)except
attachtheupholsterytooltothevacuumhose.Connectthesolutionhose.Pourhotwaterintothe
solution tank. Add recommended amount of cleaning concentrate into the solution tank.Turn on the
vacuum and pump switches.
2. Adjustthepump“operatingpressure”to50PSIforupholsterycleaning(SeePreparingthe Machine).
3. Clean with the upholstery tool using as little solution as possible. Make overlapping passes to prevent
streaking.Goovertheareayoujustcleanedwithoutdepressingthelever(vacuumonly)andgaugethe
amount ofmoistureextractedthroughtheviewwindowfordryness.Onheavilysoiledareaslike
arm rests, pre-treat with a recommended pre-spray solution or hold the upholstery tool a few inches
above the fabric and press lever to spray on the solution before making a pass.
DAILY MAINTENANCE
1. Always keep the machine clean inside and out.
2. Pour2gallonsofcleanhotwaterinthesolutiontank.Tu r n onandushtheentiresystemthroughthe
wandnozzlesforaboutaminutetopreventbuild-up.
3. Removedirtandlintbuild-upinsidethelterscreenintherecovertank.Lintshouldbecleanedoffsothat
airowisnotimpeded.
4. Check the solution tank strainer in the solution tank.If lint has accumulated in the screen, remove and
rinse it in clear running water.
PERIODIC MAINTENANCE
All EDIC machines are engineered and built to require a minimum of maintenance. But like any machine,
it does require some care to keep it in optimum working condition. Careful attention to these maintenance
instructionswillgiveyoumaximumoperatingperformanceandwillincreasethelifeexpectancyofyourma-
chine.
• SolutionLinesandFittings:Flushthemachineatleastonceamonthwithasolutionof3partswaterwith
1partwhitevinegarinordertoneutralizethealkalineresidueleftbythecleaningsolution.
• QuickConnectCoupler:SpraywithWD-40orequivalentlubricanttopreventcouplerfromsticking.
• DrainValve:Applylightoilongateseals.Ifmachinehastobestored,leavethegatevalveopen.
• SolutionPump:Thesameaboveprocedureusedonthesolutionlineandttingsappliestothepump.
GALAXY 2000WX-HR and KX-HR (BASE) PARTS LIST
ITEM # WX PART
#
KX PART
#
DESCRIPTION QTY
1C00297 #8 X .25 PAN HEAD 1
2J11863 HOSE, 3 IN 1
3J00639 SCREW CLAMP, 1.63-2.43 IN 3
4J00618 VACUUM HOSE, 2 IN GREY, WIRE, 22 IN LG 1
5F11178-BLK INTERCOOLER, GALAXY, BLACK 1
6C00273 LOCKNUT, 1-4 X 20, NYLON, SS 16
7C00233 WASHER, FLAT, .25 IN 26
8E00449 GROMMET 6
9C00284 SCREW, 10-32 X .375 GROUND 2
10 B11150 GROUND WIRE, GALAXY 2
11 G00520-1L G02517-1 WX: VACUUM, 135IN, 115V, 5.7; KX:VACUUM, 147IN., 115V, 5.7IN 2
12 J00657 HOSE CLAMP, 2 IN SLDPRT 1
13 J00618 VACUUM HOSE, 2 IN GREY, WIRE, 4 IN LG 1
14 C00261 NUT, .25-20, HEX 10
15 C00254 LOCK WASHER, 1-4 IN SPLIT 1
16 D11134 VAC PLATE 1
17 C11189 SCREW, 1-4 X 20 X 4.5 IN, HEX 5
18 C02312 LOCKWASHER, .25IN. INTERNAL STAR 1
19 C11516 SCREW, 1-4 X 20 X 4.5IN FLAT HEAD, PHILIPS 1
20 A00111 NIPPLE, .25 IN 1
21 A00052 90 ELBOW, .285MP X .25FP 4
22 A00161 TEE, .25 FP, BRASS 1
23 A00121 FITTING, .25MP X .25FP, BRASS 1
24 C11244 WASHER, .56 X 1.5 X .05 5
25 A00104 QD, 1-4M X 1-4FP, BRASS 1
26 A00154 90 ELBOW, .25 NPT X .25 NPT 3
27 C11560 WASHER, .93ID X 1.5 OD 1
28 HOSE ASSY, 13 IN X .25HP 1
29 G13133 VALVE, REGULATOR, 200 PSI 1
30 G00516-3 GAUGE, 0-600PSI 1
31 C11440 SPACER, HEATER MOUNTING PLATE 4
32 K10510 PLUG, 1.25IN, BLACK 1
33 C02322 HEX BOLT, 1-4 X 20 X 1.75IN 4
34 D010379 HEATER MOUNTING PLATE 1
35 C11165 SCREW, #8 X 1IN, PAN, BLACK 4
36 F11790 HEATER, TUNNEL, COVER, BLUE GRANITE 1
37 B11779 STUB, 12-3 SJTW YELLOW 1
38 B00191 NYLON TIE, 11IN BLACK 4
39 C00293 #8 X .5IN PAN, BLACK SMS, PHILLIPS 2
40 B00192 TIE HOLDER WITH GLUE 1
41 B11606 STRAIN RELIEF, PIGTAIL 1
42 H03545 COVER, SERIAL # LABEL 1
43 H00565-5 LABEL, SERIAL NUMBER 1
44 C02305 CAP NUT, .5 IN, PUSH-ON 2
45 C00240 WASHER, SHOULDER, NYLON 4
46 G11767 WHEEL, 10 IN 1
47 D11170 AXLE 1
48 F11789 BASE 1
49 C00314-1 HEX BOLT, 1-4 X 20 X 1 IN 8
50 G03518 CASTER, 4 IN 2
51 J00632-1 PULSE HOSE, PUMP-QD, 42 IN 2
52 A13140 CAP, FPT, .375 BRASS 1
53 G13132 PUMP, 200PSI, 120V 1
54 B00190 NYLON TIE, 4 IN 13
55 J11508 SCREW CLAMP #6, .43 TO .875 IN 6
56 D13103 PLATE, PUMP, GALAXY, FLAT 1
57 H02564-2 LABEL, CAUTION, MOTOR HOUSING 1
58 J11933 HOSE, .5 IN POLYWIRE, 20 IN 1
59 K11935 STRAINER, INLINE, .5 IN 1
60 J11933 HOSE, .5IN POLYWIRE, 33 IN 1
61 J11154 SOLUTION HOSE, .375, 100 PSI, WIRE IN LG 1
62 J00618 VACUUM HOSE, 2 IN GREY, WIRE, 7 IN LG 1
63 E11169 GASKET, VAC MOTOR, GALAXY 2
64 B00179-2 CLOSED END CNTR, 16-3 4
00580-13IN-MF-A
1
2
35
4
6
7
8
9
10
11
12
13
14 15 16
18
19
17
26
28
26
30
21
29
21 22
33 34
31
36
37
35
3839
40
42
43
41
4748 46 4445
49
7
50
10
26
38
56 57 58 59
62
64
3
63
7
45
55
17
2000WX-HR &KX-HR Base
200 PSI 4-1-08
2000WX-HR & KX-HR Base
200 PSI 4-1-08
21
61
51
32
23 24
51
60
53 54
25
27
52
ITEM
NO.
WX PART NUMBER
KX PART NUMBER
QTY.
1
C00297 #8 X .25 Pan Head
1
2
J11863 Hose, 3 in
1
3
J00639 Screw Clamp, 1.63 - 2.43in.
3
4
J00618 Vacuum Hose, 2in Grey, Wire, 22 in lg
1
5
F11178-BLK Intercooler, Galaxy, Black
1
6
C00273 Locknut, 1-4 X 20, Nylon, SS
16
7
C00233 Washer, Flat, .25 in
26
8
E00449 Grommet
6
9
C00284 Screw, 10-32 X .375 Ground
2
10
B11150 Ground Wire, Galaxy
2
11
G00520-1L Vacuum , 135 in, 115 V, 5.7 in
G02517-1 Vacuum, 117 in., 115 V, 5.7 in
2
12
J00657 Hose Clamp, 2 inSLDPRT
1
13
J00618 Vacuum Hose, 2 in Grey, Wire, 4 in lg
1
14
C00261 Nut, .25-20, Hex
10
15
C00254 Lock Washer, 1-4in Split
1
16
D11134 Vac Plate
1
17
C11189 Screw, 1-4 X 20 X 4.5 in, Hex
5
18
C02312 Lockwasher, .25 in., Internal Star
1
19
C11516 Screw, 1-4 X 20 X 4.5 in, Flat Head, Phillips
1
20
A00111 Nipple, .25 in
1
21
A00052 90 Elbow, .25MP X .25FP
4
22
A00161 Tee, .25 FP, Brass
1
23
A00121 Fitting, .25 MP X .25 FP, Brass
1
24
C11244 Washer, .56 X 1.5 X .05
5
25
A00104 QD, 1-4 M X 1-4 FP, Brass
1
26
A00154 90 Elbow, .25 NPT X .25 NPT
3
27
C11560 Washer, .93 ID X 1.5 OD
1
28
00580-13in-MF-A Hose Asm, 13 in X .25HP
1
29
G13133 Valve, Regulator, 200 PSI
1
30
G00516-3 Gauge, 0-600PSI
1
31
C11440 Spacer, Heater Mounting Plate
4
32
K10510 Plug, 1.25 in, Black
1
33
C02322 Hex Bolt,1-4 X 20 X 1.75 in
4
34
D010379 Heater Mounting Plate
1
35
C11165, Screw, #8 X 1 in, Pan, Black
4
36
F11790 Heater, Tunnel Cover, Blue Granite
1
37
B11779 Stub, 12-3 SJTW Yellow
1
38
B00191 Nylon Tie, 11in Black
4
39
C00293 #8 X .5in Pan, Black SMS, Phillips
2
40
B00192 Tie Holder with Glue
1
41
B11606 Strain Relief, Pigtail
1
42
H03545 Cover, Serial # Label
1
43
H00565-5 Label, Serial Number
1
44
C02305 Cap Nut, .5in Push-on
2
45
C00240 Washer, Shoulder, Nylon
4
46
G11767 Wheel, 10 in
2
47
D11170 Axle
1
48
F11789 Base
1
49
C00314-1 Hex Bolt, 1-4 X 20 X 1in
8
50
G03518 Caster, 4 in
2
51
J00632-1 Pulse Hose, Pump - QD, 42 in
2
52
A13140 Cap, FPT, .375 Brass
1
53
G13132 Pump, 200 PSI, 120 V
1
54
B00190 Nylon Tie, 4in
13
55
J11508 Screw Clamp #6, .43 to .875 in
6
56
D13103 Plate, Pump, Galaxy, Flat
1
57
H02564-2 Label, Caution, Motor Housing
1
58
J11933 Hose, .5 in Polywire, 20 in
1
59
K11935 Strainer, Inline, .5 in
1
60
J11933 Hose, .5 in Polywire, 33 in
1
61
J11154 Solution Hose, .375, 100PSI, Wire, 27 in lg
1
62
J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg
1
63
E11169 Gasket, Vac Motor, Galaxy
2
64
B00179-2 Closed End Cntr, 16-3
4
TROUBLESHOOTING
Electrical System
PROBLEM PROBLEM CAUSE
Noelectricalpower. 1.Defectivepowercord.
2.Houseorbuildingcircuitbreakertripped.
Switchisturnedon. 1.Faultyelectricalcable.
Powerisintermittentto 2.Defectiveswitches.
allmotor(s) 3.Looseterminalordiscoloredterminalconnections.
Vacuum System
1. Drain valve open.
NoVacuum 2.Vacuumlidisnotsealedagainsttank.
3. Loose vacuum hose, vacuum connection.
LowVacuum 1.Accumulateddirtonlidscreen.
2.Wornoutvacuumlidgasket.
3.Lint&dirtbuild-uponwandhead.
4. Defective vacuum hose.
5.Looseconnectioninone of thevacuummotors.
Solution System
Pumpmotoron,no 1.Cloggedspraytips.
spraythruspraytips 2.Cloggedsolutionintakelterscreen.
3.Pluggedfemalequickdisconnectcoupler.
4.Puncturedpumpdiaphragm.
5.Defectivepumpcheckvalve.
6. Crack in pump housing.
7.Debrisincheckvalve.
8.LostPrime.
Unevenorweakspray 1.Cloggedordirtyspraytips.
fromtips. 2.Accumulateddirtonsolutionintakelterscreen.
3. Accumulation of debris inside pump and plumbing.
4.Wornpumpbearing(excessivenoise).
5.Puncturedpumpdiaphragm.
6.Defectiverectierormotor.
7.Wornnozzles.
8.Pressureregulatorsetincorrectly.
Vacuummotor(s) 1.Loosewiringconnection.
working,pumpmotor 2.Defectivepressureswitchinpump.
failstoturnon 3.Defectivepumpmotororrectier.
ErraticPressure 1.Pumpcheckvalvesdefectiveordirty.
2.Lostprime.
OPTIONAL ACCESSORIES
HEAT-N-RUN
NOTES
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
_________________________________
43
6
7
8
9
10
11
1
2
12 13 14 15 16 17 18 19 20
21
22
23
24
25
26
27
28
2930
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
Upper
3-25-08
2700MX-HR Upper
3-25-08
5B
5D
5A
5
5C
A
B
C
D
53
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
F11787-1 Solution Tank, Galaxy Pro
1
2
F11788-1 Recovery Tank, Galaxy Pro
1
3
F11791-1 Lid, Sol Tank, Galaxy Pro
1
4
G11836 Gasket, Recovery Tank
1
5
12904A Stand Pipe Assembly
1
K11965 Elbow, 180 Deg. Float Ball
1
K00672 Pvc Pipe, 1.5 X 12 in, Sch 40 Wht
1
10989-2A Float Ball Screen
1
K00741 Adapter
1
6
F11785-1 Lid, Recovery Tank
1
7
C11167 Bolt, 1-4 X 20
6
8
K02714 Plug, .500
4
9
B11769 Extension Cord, 12-3 SJTW
1
10
C11177 Velcro Strap
1
11
H02548-2 Label, Important, Cord
1
12
B00185-30 Wires, 73 in
1
13
B00185-40 Wires, 73 in
1
14
B010314 Wire Harness
1
15
F11786-1 Handle
1
16
B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated
2
17
B00185-40 Wire,14 GA Black, UL1015, 5 in
1
18
C00295-1 #10 X .75in Pan, Black SMS, Phillips
2
19
C00293 #8 X .5in Pan, Black SMS, Phillips
2
20
D11168 Cover, Switchplate, Galaxy
1
21
B02211-1 Switch, Rocker, Green Light
3
22
D010284 Switchplate
1
23
E010453 Gasket, Switch Bracket
1
24
B00177-1 Terminal Lug, Female, QD, .25 X .032
4
25
B00185-30 Wire,14 GA White, UL1015, 5 in
1
26
C02315 Lockwasher, #10 Int. Str, SS
2
27
C00264 Nut, 10-32
1
28
C00288-1 .25-20 X 2.25 Flat Head
4
29
C00288 .25-20 X 1.5 Flat Head
4
30
K00666 90 Elbow, SCH D 40, 1.5 in
1
31
K00665-1 Hose Adapter, 1.5in, Black
1
32
C00313 Hex Bolt, .25 X 20 X .75
2
33
C02312 Lockwasher, .25 in., Internal Star
2
34
C00314-1 Hex Bolt, 1-4 X 20 X 1in
4
35
C00233 Washer, Flat, .25 in
6
36
D010283 Plate, Heater Mounting
1
37
F11804 Heater Mount
1
38
C00261 Nut, .25-20, Hex
2
39
K00710 Elbow, Drain Valve, Black
1
40
K00711 Drain Valve, Black
1
41
E11128 Gasket, Drain Valve
1
42
C12110 Hex Bolt, .375-16 X 1.75
2
43
C11540 Washer, .375 ID X .875 OD
2
44
K11185 Elbow, 90, 1.5 in, MT-MS, PVC
1
45
K00672-1 Pvc Pipe, 1.5 X 2.25 in, Sch 40 Wht
1
46
A00060 3-8 Barb X 1-4MP, Brass
1
47
A00052 .25 X .375 M-F 90 deg Brass
1
48
C11244 Washer, .56 X 1.5 X .05
1
49
A00124 Hex Nut, .25 NPT Brass
1
50
D00373 Inlet Filter, .25 NPT
1
51
C11144 Screw, .25-20 X 2, SS
2
52
S11179 Non-Skid Tape, 1 in. Roll
1
53
C00238 Washer, .275 in, Neosteel
2
17 GALLON GALAXY 200 PSI (UPPER) PARTS LIST
ITEM # PART # DESCRIPTION QTY
1F11787-BLANK SOLUTION TANK, GALAXY PRO 1
2F11788-1 RECOVERY TANK, GALAXY PRO 1
3F11791-1 LID, SOLUTION TANK, GALAXY PRO 1
4G11836 GASKET, RECOVERY TANK 1
512904A STAND PIPE ASSY 1
AK11965 ELBOW, 180 DEG. FLOAT BALL 1
BK00672 PVC PIPE, 1.5 X 12 IN, SCH 40 WHT 1
C10989-2A FLOAT BALL SCREEN 1
DK00741 ADAPTER 1
6F11785-1 LID, RECOVERY TANK 1
7C11167 BOLT, 1-4 X 20 6
8K02714 PLUG, .500 4
9B11769 EXTENSION CORD, 12-3 SJTW 1
10 C11177 VELCRO STRAP 1
11 H02548-2 LABEL, IMPORTANT, CORD 1
12 B00185-30 WIRES, 73 IN 1
13 B00185-40 WIRES, 73 IN 1
14 B010314 WIRE HARNESS 1
15 F11786-1 HANDLE 1
16 B00177 TERMINAL LUG, FEMALE, QD , .25 X .032, 16-14 AWG FULLY INSULATED 2
17 B00185-40 WIRE, 14 GA BLACK, UL1015, 15IN 1
18 C00295-1 #10 X .75INPAN, BLACK SMS, PHILLIPS 2
19 C00293 #8 X .5IN PAN, BLACK SMS, PHILLIPS 2
20 D11168 COVER, SWITCHPLATE, GALAXY 1
21 B02211-1 SWITCH, ROCKER, GREEN LIGHT 3
22 D010284 SWITCHPLATE 1
23 E010453 GASKET, SWITCH BRACKET 1
24 B00177-1 TERMINAL LUG, FEMALE, QD, .25 X .032 4
25 B00185-30 WIRE, 14 GA WHITE, UL1015, 5IN 1
26 C02315 LOCKWASHER, #10 INT. STR,SS 2
27 C00264 NUT, 10-31 1
28 C00288-1 .25-20 X 2.25 FLAT HEAD 4
29 C00288 .25-20 X 1.5 FLAT HEAD 4
30 K00666 90 ELBOW, SCH D 40, 1.5 IN 1
31 K00665-1 HOSE ADAPTER, 1.5 IN, BLACK 1
32 C00313 HEX BOLT, .25 X 20 X .75 2
33 C02312 LOCKWASHER, .25 IN, INTERNAL STAR 2
34 C00314-1 HEX BOLT, 1-4 X 20 X 1 IN 4
35 C00233 WASHER, FLAT, .25 IN 6
36 D010283 PLATE, HEATER MOUNTING 1
37 F11804 HEATER MOUNT 1
38 C00261 NUT, .25-20, HEX 2
39 K00710 ELBOW, DRAIN VALVE, BLACK 1
40 K00711 DRAIN VALVE, BLACK 1
41 E11128 GASKET, DRAIN VALVE 1
42 C12110 HEX BOLT, .375-16 X 1.75 2
43 C11540 WASHER, .375 ID X .875 OD 2
44 K11185 ELBOW, 90, 1.5IN, MT-MS, PVC 1
45 K00672-1 PVC PIPE, 1.5 X 2.25 IN, SCH 40 WHT 1
46 A00060 3-8 BARB X 1-4MP, BRASS 1
47 A00052 .25 X .375 M-F DEG BRASS 1
48 C11244 WASHER, .56 X 1.5 X .05 1
49 A00124 HEX NUT, .25 NPT, BRASS 1
50 D00373 INLET FILTER, .25 NPT 1
51 C11144 SCREW, .25-20 X 2, SS 2
52 S11179 NON-SKID TAPE, 1 IN ROLL 1
53 C00238 WASHER, .275 IN, NEOSTEEL 2
2 3 4 6 7 8 9
11
12
13
15
16
272625
24
2220 21
22 28
34
3738
55
3940
454647
46
4849
50
7
51
52
54
56 57 58 59
62
54
6
17
7
63
64
65
66
32
33
42
41
7
15
31
60
61
23
53
BASE
2-3-08
2000MX-HR Base
2-3-08
36
1
14
19
18
29
43
44
55
6
35
30
5
10
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
C00297 Screw,#8 X .25 in, Pan Head
1
2
J11863 Hose, 3 in
1
3
J00639 Screw Clamp, 1.63 - 2.43in.
3
4
J00618 Vacuum Hose, 2in Grey, Wire, 22 in lg
1
5
F11178-BLK Intercooler, Galaxy, Black
1
6
C00273 Locknut, 1-4 X 20, Nylon, SS
16
7
C00233 Washer, Flat, .25 in
26
8
E00449 Grommet
6
9
C00284 Screw, 10-32 X .375 Ground
2
10
B11150 Ground Wire, Galaxy
2
11
G00520-IL Vacuum, 106 in, 115 V, 5.7 in
2
12
J00657 Hose Clamp, 2 inSLDPRT
1
13
J00618 Vacuum Hose, 2 in Grey, Wire, 4 in lg
1
14
C00254 Lock Washer, 1-4in Split
1
15
C00261 Nut, .25-20, Hex
10
16
D11134 Vac Plate
1
17
C11189 Screw, 1-4 X 20 X 4.5 in, Hex
5
18
C11516 Screw, 1-4 X 20 X 4.5 in, Flat Head, Phillips
1
19
C02312 Lockwasher, .25 in., Internal Star
1
20
G11314-2 Pressure Regulator, 180 PSI
1
21
A00060 3-8 Barb X 1-4MP, Brass
1
22
A00052 .25 X .375 M-F 90 deg Brass
3
23
A00161 Tee, .25 FP, Brass
1
24
A00111 Nipple, .25 in
2
25
A00121 Fitting, .25 MP X .25 FP, Brass
1
26
C11244 Washer, .56 X 1.5 X .05
2
27
A00104 QD, 1-4 M X 1-4 FP, Brass
1
28
A00097A Cap, Inline Filter
1
29
A00094E Checkvalve, No Strainer
1
30
A00094C Check Valve Body
1
31
C02322 Hex Bolt,1-4 X 20 X 1.75 in
4
32
D010379 Heater Mounting Plate
1
33
C11440 Spacer, Heater Mounting Plate
4
34
A00061 3-8 Barb X 1-4FP, Brass
1
35
H02564-2 Label, Caution, Motor Housing
1
36
C11165, Screw, #8 X 1 in, Pan, Black
4
37
F11790 Heater, Tunnel Cover, Blue Granite
1
38
B11779 Stub, 12-3 SJTW Yellow
1
39
C00293 #8 X .5in Pan, Black SMS, Phillips
2
40
B00192 Mount, Nylon Tie
1
41
B11606 Strain Relief, Pigtail
1
42
K10510 Plug, 1.25 in, Black
1
43
H03545 Cover, Serial # Label
1
44
H00565-5 Label, Serial Number
1
45
C02305 Cap Nut, .5in Push-on
2
46
C00240 Washer, Shoulder, Nylon
4
47
G11767 Wheel, 10 in
2
48
D11170 Axle
1
49
F11789 Base
1
50
C00314-1 Hex Bolt, 1-4 X 20 X 1in
8
51
G03518 Caster, 4 in
2
52
J00613B Solution Hose, .375 in, Black
1
53
J11508 Screw Clamp #6, .43 to .875 in
8
54
A00054 Elbow, 90, .375MP X .375B, Nylon
2
55
B00191 Nylon Tie, 11in Black
4
56
B00190 Nylon Tie, 4in
13
57
G11234 Pump, 150 PSI
1
58
D11194 Pump Plate
1
59
J00613B Solution Hose, .375 X 26 in, Black
1
60
J11154 Solution Hose, .375 X 10 in, Wire Reinforced
1
61
A11243 Tee, .375B X .375B X .375B, Nylon
1
62
J11154 Solution Hose, .375 X 6 in, Wire Reinforced
1
63
J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg
1
64
E11169 Gasket, Vac Motor, Galaxy
2
65
B00179-2 Closed End Cntr, 16-3
1
66
B00179-1 Closed End Cntr, 16-3
3
17 GALLON GALAXY 200 PSI (BASE) PARTS LIST
ITEM # PART # DESCRIPTION QTY
1C00297 SCREW, #8 X .25IN, PAN HEAD 1
2J11863 HOSE, 3IN 1
3J00639 SCREW CLAMP, 1.63-2.43IN 3
4J00618 VACUUM HOSE, 2 IN GREY, WIRE22 IN LG 1
5F11178-BLK INTERCOOLER, GALAXY, BLACK 1
6C00273 LOCKNUT, 1-4 X 20, NYLON, SS 16
7C00233 WASHER, FLAT, .25 IN 26
8E00449 GROMMET 6
9C00284 SCREW, 10-32 X .375 GROUND 2
10 B11150 GROUND WIRE, GALAXY 2
11 G00537 VACUUM, 82 IN, 115 V, 5.7 IN 1
12 J00657 HOSE CLAMP, 2 IN SLDPRT 1
13 J00618 VACUUM HOSE, 2 IN GREY, WIRE, 4 IN LG 1
14 C00254 LOCK WASHER, 1-4 IN SPLIT 1
15 C00261 NUT, .25-20, HEX 10
16 D11134 VAC PLATE 1
17 C11189 SCREW, 1-4 X 20 X 4.5IN, HEX 5
18 C11516 SCREW, 1-4 X 20 X 4.5IN, FLAT HEAD, PHILLIPS 1
19 C02312 LOCKWASHER, .25 IN, INTERNAL STAR 1
20 G11314-2 PRESSURE REGULATOR, 180 PSI 1
21 A00060 3-8 BARB X 1-4 MP, BRASS 1
22 A00052 .25 X .375 M-F 90 DEG, BRASS 3
23 A00161 TEE, .25 FP, BRASS 1
24 A00111 NIPPLE, .25 IN 2
25 A00121 FITTING, .25 MP X .25 FP, BRASS 1
26 C11244 WASHER, .56 X 1.5 X .05 2
27 A00104 QD, 1-4M X 1-4FP, BRASS 1
28 A00097A CAP, INLINE FILTER 1
29 A00094E CHECKVALVE, NO STRAINER 1
30 A00094C CHECK VALVE BODY 1
31 C02291 HEATER PLATE HEX 4
32 D010379 HEATER MOUNTING PLATE 1
33 K10691 PVC PIPE, .25IN 4
34 A00061 3-8 BARB X 1-4RP, BRASS 1
35 H02564-2 LABEL, CAUTION, MOTOR HOUSING 1
36 C11165 SCREW, #8 X 1 IN, PAN, BLACK 4
37 F11790 HEATER, TUNNEL COVER, BLUE GRANITE 1
38 B11779 STUB, 12-3 SJTW, YELLOW 1
39 C00293 #8 X .5 IN PAN, BLACK SMS, PHILLIPS 2
40 B00192 MOUNT, NYLON TIE 1
41 B11606 STRAIN RELIEF, PIGTAIL 1
42 K10510 PLUG, 1.25 IN, BLACK 1
43 H03545 COVER, SERIAL # LABEL 1
44 H00565-5 LABEL, SERIAL NUMBER 1
45 C02305 CAP NUT, .5 IN PUSH- ON 2
46 C00240 WASHER, SHOULDER, NYLON 2
47 G11767 WHEEL, 10 IN 2
48 D11170 AXLE 1
49 F11789 BASE 1
50 C02310 HEX BOLT, 1/4 X 20 X 1 1/4" 8
51 G03518 CASTER, 4 IN 2
52 J00613B SOLUTION HOSE, .375 IN, BLACK 1
53 J11508 SCREW CLAMP #6, .43 TO .875 IN 8
54 A00054 ELBOW, 90, .375 MP X .375B, NYLON 2
55 B00191 NYLON TIE, 11 IN BLACK 4
56 B00190 NYLON TIE, 4 IN 13
57 G13132 PUMP, ADJUSTABLE PRESSURE 50 - 200 PSI 1
58 D11835M-1 PUMP PLATE 1
59 J00613B SOLUTION HOSE, .375 X 26 IN, BLACK 1
60 J11154 SOLUTION HOSE, .375 X 10 IN, WIRE REINFORCED 1
61 A11243 TEE, .375B X .375B X .375B, NYLON 1
62 J11154 SOLUTION HOSE, .375 X 6 IN, WIRE REINFORCED 1
63 J00618 VACUUM HOSE, 2 IN GREY, WIRE, 7 IN LG 1
64 E11169 GASKET, VAC MOTOR, GALAXY 2
65 B00179-2 CLOSED END CNTR, 16-3 1
66 B00179-1 CLOSED END CNTR, 16-3 3
Table of contents
Other Trusted Clean Floor Machine manuals
Trusted Clean
Trusted Clean TPL-BK-17-TC Owner's manual
Trusted Clean
Trusted Clean TPL-BK-13-TC Owner's manual
Trusted Clean
Trusted Clean TPL-SS-17-TC User manual
Trusted Clean
Trusted Clean SS-20-1500HS-TC User manual
Trusted Clean
Trusted Clean TPL-SS20-TC User manual
Trusted Clean
Trusted Clean Dura 18 User manual
Trusted Clean
Trusted Clean TPL-7-100-SCE-TC User manual
Trusted Clean
Trusted Clean TPL-5-100-UD-TCP User manual
Trusted Clean
Trusted Clean TPL-17-150-CE-HEAT-TCP User manual
Popular Floor Machine manuals by other brands
Kent Euroclean
Kent Euroclean SelectGloss 21PH Operator's manual and parts list
China Honway Machinery
China Honway Machinery HWG 400 Operator's instruction manual
Imetec
Imetec Piuma Force Cordless 32V operating instructions
Wetrok
Wetrok Duomatic operating instructions
Chariot
Chariot Chariot 86037880 parts list
Bissell
Bissell BG10 10N2 Series user guide
