Trusted Clean TPL-BK-17-TC Owner's manual

LOW SPEED AND DUAL SPEED
FLOOR MACHINE
OWNER’S/OPERATOR’S MANUAL
FOR MODELS:
TPL-BK-17-TC
TPL-BK-20-TC
TPL-BK-17VS-TC
TPL-BK-20VS-TC
WWW.CLEANFREAK.COM
888-722-5508
REVISED 9-6-22

UNPACKING YOUR NEW EQUIPMENT:
When your package is delivered, check each of the 3
cartons carefully for signs of rough handling. If the
EQUIPMENT is damaged, notify the carrier immediate-
ly and request an inspection. Be sure to keep the cartons,
packing inserts, packing lists and carrier’s receipt until
the inspector has veried your claim.
CLEANFREAK’s liability ceases when the carrier picks
up the shipment. However, our customer service sta
will be happy to furnish any information needed in
connection with the claim and will attempt to expedite a
resolution.
PLEASE READ BEFORE
OPERATING YOUR NEW EQUIPMENT:
Read the manual carefully and completely before at-
tempting to operate the unit. is manual has important
information for the use and safe operation of the ma-
chine. Keep this manual handy at all times.
is equipment has been engineered and manufactured
to provide excellent performance and service. To ensure
that your equipment will continue to perform as intend-
ed:
• Maintain and inspect equipment regularly
• Use only original CLEANFREAK parts when servic-
ing.
• Operate equipment with care.
If additional information is needed, please contact
CLEANFREAK at: 888-522-5508
All information and specications printed in the manual
are current at the time of printing; however, because of
CLEANFREAK’s policy of continual product improve-
ment, we reserve the right to make changes at any time
without notice.
FAILURE TO COMPLY WITH THE FOLLOWING
WARNINGS AND INSTRUCTIONS WILL VOID
THE WARRANTY.
WARNING!
• Do not operate the machine unless trained and au-
thorized.
• Do not leave the machine unattended when plugged
in. Unplug from the outlet when not in use, before
servicing, and when changing the brushes or pads.
• Use indoors only.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Do not bypass or defeat the safety “lock-out lever.”
• e machine was designed for use as per instruc-
tions and recommendations written in this manual.
Any deviation from its proper use or purpose and
the consequential damage that may occur is the sole
responsibility of the end user.
• Do not use with damaged cord or plug. If the ma-
chine is not working as it should, or it has been
dropped, damaged, le outdoors or dropped into
water, take it to an authorized service center.
• Do not pull or carry by cord, use cord as handle,
close a door on the cord or pull cord around sharp
edges or corners. Do not run machine over cord.
Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Make sure the machine is plugged into an electrical
outlet with the same voltage and frequency rating
as shown on the nameplate of the machine. Do not
attempt to plug a 115- volt machine into a 230- volt
outlet.
• Do not immerse or use this machine in standing
water. Such use can cause electric shock.
• Keep the electrical supply cord from contacting the
rotating brush or drive block.
• Do not expose machine to freezing temperatures.
• To avoid electric shock, do not expose the unit to
rain. Store indoors only.
• Connect to a properly grounded outlet only. See
“Grounding Instructions.”
• Turn o all controls before unplugging.
• When using an extension cord, use a 3 conductor-
grounding cord, 12 gauge wire or heavier. Do not use
more than 25’ of extension cord.
• Do not put any object into openings.
• Do not use with any opening blocked. Keep free of
dust, lint, hair and anything that may reduce air ow.
• Do not operate machine in ammable or explosive
areas.
2

• All servicing of CLEANFREAK equipment should be
performed by an CLEANFREAK authorized service
center.
• Keep hair, loose clothing, ngers and all parts of
body away from openings and moving parts.
• Use extra care when cleaning near stairs.
• When servicing machine, use manufacturer’s sup-
plied or approved replacement parts.
• Do not wrap the cord too tightly when storing.
• Work only in well lit areas.
• is equipment is heavy. Use proper liing tech-
niques when liing heavy equipment.
PROPER LIFTING TECHNIQUES:
1. Stand close to the load with your feet spread shoul-
der width apart. One foot should be slightly in front
of the other for balance
2. Squat down, bending at the knees (not your waist).
Tuck your chin while keeping your back as vertical as
possible
3. Get a rm grasp of the object before beginning the
li.
4. Slowly begin straightening your legs, liing slowly.
Never twist your body during this step.
5. Once the li is complete, keep the object as close to
the body as possible. If the load’s center of gravity
moves away from your body, there is a dramatic in-
crease in stress to the lumbar region of the back.
GROUNDING INSTRUCTIONS:
is piece of equipment must be grounded. Should an
electrical malfunction occur, grounding provides a path
of least resistance for electrical current- reducing the risk
of electric shock. is piece of equipment is furnished
with a cord that has a grounding conductor and ground-
ing plug. e grounded plug must only be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordi-
nances.
WARNING:
Connecting the equipment to an improperly grounded
outlet can result in an increased risk of electric shock. A
qualified electrician should be consulted if you are un-
sure that the outlet is properly grounded. Do not modify
the plug provided with the equipment. If it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
is appliance is designed for use on a 120-volt circuit.
e grounding plug provided looks like the plug illus-
trated in Figure 1. Replace the plug if the grounding pin
is damaged or broken.
e Green (or Green/Yellow) wire in the cord is the
grounding wire. When replacing a plug, this wire must
be attached to the grounding pin only.
DO NOT use extension cords.
Servicing:
In the event that your EQUIPMENT requires service,
please contact CLEANFREAK at: 888-522-5508
Do not attempt repairs yourself. CLEANFREAK will
assist you in locating an indepedent service contractor.
Fig. 1
3
1. 2.
3. 4.
5.

FINAL ASSEMBLY INSTRUCTIONS:
PLEASE READ MANUAL COMPLETELY BEFORE
PROCEEDING TO FINAL ASSEMBLY INSTRUC-
TIONS ON PAGE 5
PREPARING THE MACHINE FOR
OPERATION
Your oor machine will operate in a wide variety of hard
oors and carpet cleaning applications. Consult with
your local dealer or CLEANFREAK Customer Service to
select the correct accessories for the job you are going to
perform.
BRUSH, PAD DRIVER
INSTALLATION
Lock the handle in the upright position and tip the ma-
chine back so it rests on the handle and wheels. Fit the
three slots of the clutch plate in the back of the brush
or pad driver over the three lugs of the drive plate (Fig.
1). Push it rmly into position and turn it counterclock-
wise until it locks in place (Fig. 2).
TO REMOVE PAD DRIVER: Tip the machine back so it
rests on the
handle and wheels. Turn the brush or pad driver
clockwise until it disengages and lis o. Do not store
the machine with the brush or pad drivers installed.
PAD INSTALLATION
TO INSTALL PAD: Tilt the machine back on wheels un-
til machine is resting on handle. Center the pad on the
pad holder and place the pad onto the pad holder.
TO REMOVE PAD: Simply remove the pad from the
pad holder by pulling it away from the pad holder with
steady force.
MACHINE OPERATION
1. Install the pad driver and pad, brush or attachment.
2. Plug in machine.
3. Lower the handle to the desired operating position.
4. Place both hands on the handle grips with your n-
gers around the ON/OFF lever which extends from
one side to the other underneath the handle grips.
5. e safety LOCK-OUT lever is located underneath
the right side handle grip and ON/OFF lever. To
unlock the LOCK-OUT lever, use your right hand
forenger to press the lever down toward the back of
the switch box
6. While pressing the LOCK-OUT lever, pull the ON/
OFF lever on either side of the handle to start the
machine.
7. e LOCK-OUT lever will automatically lock when
you release the ON/OFF lever preventing the ma-
chine from being turned on until it is unlocked
again.
TO MANEUVER YOUR FLOOR MACHINE
1. Raise the handle slightly and the machine will go to
the right. e higher you raise it, the faster it will go.
2. Lower the handle and the machine will go le. e
more you lower it, the faster it will go.
3. Practice on a smooth surface to gain experience in
operating the unit before moving on to other surfac-
es.
DUAL SPEED FUNCTION FOR 17DS3-BK-P
& 20DS3-BK-P:
Use the black switch located directly behind the motor
to switch between low speed (180RPM) and high speed
(320RPM). Do not change speeds while machine is run-
ning. Always wait until motor has stopped completely
before changing speeds.
Storage:
Wipe with a clean damp cloth aer every use.
Store in a clean dry place.
CORD STORAGE:
• Unplug the cord- Clean and inspect for damage.
4

• Wrap the cord around the le side handle grip.
• Do not wrap too tightly.
FINAL ASSEMBLY INSTRUCTIONS:
PLEASE CHECK THAT YOU HAVE RECEIVED 3
CARTONS. EACH CARTON IS MARKED, AS FOL-
LOWS:
1. BASE ASSEMBLY
2. HANDLE ASSEMBLY
3. BRUSH COVER ASSEMBLY
Open all three cartons and pull out the assemblies. e
base assembly in carton 1 is encased in a clam shell foam
assembly. pull o the top foam piece exposing the base
assembly inside. Reach and grab the base assembly and
pull it out using proper liing techniques. e assembly
is very heavy (75lbs), ask for assistance if you cannot
do it by yourself. Check for damage- report damage to
freight carrier immediately. If no damage is present, pro-
ceed to the following nal assembly procedure.
Tools required:
• 5/16” Allen wrench
• Pair of adjustable wrenches or three open wrenches
(9/16”, 7/8”, and 13/16”)
ASSEMBLY OF THE BRUSH COVER TO MOTOR
ASSEMBLY:
1. Place motor base assembly upside down on the oor
or on a work bench. use a towel or so material to pre-
vent damaging the nish.
2. Pull out the brush cover from carton 3 and align the
four holes on the brush cover to the four holes on the
motor. e two plastic caps on the brush cover should
be positioned at the front of the motor.
3. Use the four screws in the bag and mount the brush
cover. Hand-tighten the screws rst and then use a
wrench to tighten them rmly. Use a CROSS pattern to
tighten the bolts as shown below.
4. Flip the motor base and place it on the oor right side
up aer making sure the brush cover is
rmly attached.
5

6
5. Open the handle carton and set the handle nearby the
motor base.
6. Unscrew the nut (C13100 )from the pivot axle screw
(C22558). Slide out the pivot axle screw from the
handle bracket on the motor base frame.
7. Insert the pivot tube at the lower end of the handle be-
tween the handle bracket on the base frame and align the
holes to one another.
8. Insert the pivot axle screw (C22558) through the
handle bracket and the handle pivot tube. Hand tighten
the nut (C13100) to the pivot axle screw and nish by
tightening with a wrench.
ASSEMBLY OF THE HANDLE TO THE MOTOR
BASE:
1. Locate the nut (C11558) on the end of the locking
clamp handle assembly (C11536) and unfasten it.
2. Slide out the locking clamp handle (D11497) assembly
with spade bolt (C11536) and set it aside.

7
3. Insert the locking clamp handle/spade bolt assembly
through the Cord Hook Clamp assembly (located on the
handle) and the le and right handle braces ( D11481,
D11482).
4. Put the locking clamp handle in the unlocked position
(pointing up) and start tightening the nut C11558 on the
threaded portion of the spade bolt (C11536).
5. Check the cord hook clamp is sliding up
and down freely on the handle stem with lock-
ing clamp handle in the unlocked position.
6. Place the handle in the down position to check the
locking function. If too tight, unlock the handle and loos-
en the nut (C11558) slightly. If too loose, unlock the the
handle and tighten the nut (C11558), as needed. You have
assembled the cord hook clamp assembly properly when
the locking handle locks rmly in the DOWN position
and unlocks and slides easily in the UP position.
7. Plug the male motor cord plug to the female handle
cord plug. Your Assembly is done. Refer to Brush/Pad
driver installation and operation sections before operat-
ing the unit.

7