TSS 3x3 Power Rack with Belt Squat User manual

3x3 Power Rack with Belt Squat

Read all safety warnings, instructions and
illustrations provided for this piece of strength
equipment. Failure to follow all instructions listed
below may result in serious injury or death. User assumes all potential
risks of assembly or use of this product.
PERSONAL SAFETY
●Stay alert, watch what you are doing when assembling and operating the
strength equipment. Do not use the strength equipment while you are
tired or under the influence of drugs, alcohol or medication. A moment
of inattention while operating or assembling the strength equipment may
result in serious or fatal injury.
EQUIPMENT USE AND CARE
●Visually inspect all components in order to identify potential
deformation or damage. If damages are observed, discontinue assembly
and contact the manufacturer at [email protected],
[email protected].
●Multiple components involved with assembly of this piece of strength
equipment are above 50lbs and it is recommended that you have an
additional person to assist in the positioning of these items.
●Ensure that all components are securely fastened before use.
1

Required Tools
●Crescent Wrench
●1 ⅛” and 9/16” Socket and Wrench
●5/32 Allen Key
Parts
3PRBS-001 |(x1) |Part A
OR
*3PR-100 |(x1) |Part MB*
(Upgrade; Replaces Part A)
3PRBS-002 |(x1) |Part B
3PRBS-003 |(x1) |Part C
3PRBS-004 |(x2) |Part D
3PRBS-005 |(x1) |Part E
2

3PRBS-006 |(x1) |Part F
3PRBS-007 |(x2) |Part G
3PRBS-008 |(x1) |Part H
3PRBS-009 |(x1) |Part I
3PRBS-010 |(x1) |Part J
3PRBS-011 |(x1) |Part K
3PRBS-012 | (x1) | Part L
3

3PRBS-013 |(x2) |Part M
76 ½” Cable |(x1) |Part N
84 ½” Cable |(x1) |Part O
3PRBS-014 |(x2) |Part P
3PRBS-016 |(x2) |Part R
3PRBS-017 | (x2) | Part S
3PRBS-018 | (x2) | Part T
4

3PRBS-015 |(x2) |Part Q
3PRBS-019 |(x8) |Part U
Carabiner |(x3) |Part V
¾” Nut |(x20) |Part W
¾” Flat Washer |(x16) |Part X
¾” Lock Washer |(x20) |Part AB
⅜” Flat Washer |(x18) |Part AC
⅜” Lock Nut |(x20) |Part AD
⅜” Wing Nut |(x2) |Part AE
¾ x 4.5” Bolt |(x20) |Part Y
⅜” x 7.5” Bolt |(x2) |Part Z
5

Rubber Stopper |(x2) |Part AF
Spacer |(x2) |Part AG
⅜” x 4” Bolt | (x20) |Part AA
Pulley | (x1) |Part AH
Set Screw Collar |(x2) |Part AI
6

Assembly
Image 1 above displays the assembly of parts L, M, AF, and AI.
7

In the Image 2 above the arrows
display where parts C, E and D
will be attached with parts Q and
T respectively. The organization
of the hardware for these
locations can be seen in Image 3
below.
Part C will have part Q placed
with it in the organization
displayed in Image 3 above and
part E will have part T placed
with it in the same organization
as part C and Q.
8

In Image 4 above displays where
all other ¾” hardware will be
placed and the organization of
the hardware can be seen in
Image 5 below.
9

Using the parts that were assembled in image 1 place them into part E
until the assembly is above part C and slide them into part C. Once the
assembly has been properly placed, tighten part AI right below part E
using a 5/32 allen key.
10

Parts G, H, Z, AE, AG, and AH will come pre-assembled in the manner
displayed above. Parts H and AH can be placed in different locations as
desired; above simply shows them placed in the center holes of part G.
11

Parts I and J will be placed on top of the power rack as seen in image 8
above. The assembly created in image 7 will be placed beneath the parts
I and J as seen in image 8. Parts I, J, and the previous assembly will be
attached with parts AA and AD. Part AG will act as a spacer and be
placed as seen in image 8.
12

Attach part N to part L with part V. With part V removed on the other
end feed part N through the hole in part E and across part B as seen in
image 9 above.
13

Image 10 above displays the organization of the ⅜” hardware which will
be used for part U.
14

*Place P, R, and S in desired location*
15

Place part F on top of part D. Attach part O to N with part V. Feed part O
underneath part F ensuring that it lines up with the pulley underneath
part F. *These parts can be removed and attached as desired.*
16

To use the low cable system attach part O to N with V and feed it
through part K as seen in image 13. *These parts can be removed and
attached as desired.*
17

You have now completed assembling your very own 3x3 Rack with
Weight Storage and Belt Squat Attachment! Thank you for choosing
Texas Strength Systems for your fitness needs. If you have any questions,
comments, or concerns please don’t hesitate to contact our staff.
Contact Information
Email: [email protected]
Phone: [phone]
18