TUNA ID551PN User manual

1
ID551PN WEIGHING CONTROLLER
OPERATION MANUAL
2017/03
Rev 1.00

ID551PN Weighing Controller
2
Contents
Chapter 1 Introduction......................................................................................................................................4
1.1 Overview.................................................................................................................4
Chapter 2 Keypad and Setup Menu............................................................................................................5
2.1 Keypad ...................................................................................................................5
2.2 Top Menu................................................................................................................6
2.3 Setup......................................................................................................................6
2.3.1 1#Channel Scale...............................................................................................6
2.3.2 2#Channel Scale...............................................................................................8
2.3.3 3#Channel Scale...............................................................................................9
2.3.4 4#Channel Scale.............................................................................................11
2.3.5 Serial Port.......................................................................................................12
2.3.6 Network Configuration .....................................................................................13
2.3.7 Maintenance ...................................................................................................14
Chapter 3 Serial Port Application..............................................................................................................15
3.1 Serial Port and Ethernet continuous output weight format.........................................15
3.2 Continuous output A/D Code format ........................................................................16
3.3 Demand Input / Output...........................................................................................16
3.4 MODBUS-RTU1 & MODBUS-TCP1 Data Format ....................................................18
3.5 MODBUS-RTU2 & MODBUS-TCP2 Data Format ....................................................22
3.6 PROFINET Data Format ........................................................................................24
Chapter 4 Hardware..........................................................................................................................................26
4.1 Interface Specification............................................................................................26
4.2 Housing Size.........................................................................................................27
Appendix 1 Calibration...................................................................................................................................28
Appendix 2 Display Message & Error Code..........................................................................................29

ID551PN Weighing Controller
3
Change Log
Version Change Date
V1.00 1
st
Version 2017/03

ID551PN Weighing Controller
4
Chapter 1 Introduction
1.1 Overview
Four analog load cell I/F, support up to eight 350 Ohm load cells
Up to 150,000 displayDivision
200Hz weight updating speed
6-bit LED segment display
One serialports
RS232 /RS485
100M LAN port
TCP, MODUS-TCP
Support PROFINET, Dual network, Switch function
Pushbutton Zero, Auto Zero
Pushbutton Tare
Motion Checki ng
Keyboard Lock / UnLock
MODBUS、PROFINET remote calibrationfunction
Calibration
2-point Calibration or Cal-Free Calibration
Local Calibration or Remote Calibration (via
MODBUS-RTU,MOUBUS-TCP, PROFINETPLC communication)
Support PC software and Andriod phone APP for parameters upload,
download and save, and calibrate scale, weight display.
Power In : 85-264VAC，49-61Hz
Operating Environment
Operating Temperature: -10℃∼40℃
Humidity: 10％RH∼95％RH,non-condensing

ID551PN Weighing Controller
5
Chapter 2 Keypad and Setup Menu
2.1 Keypad
Key
Operation Set Menu Key Operation Set Menu
Zero Go back to
the previous
menu and
exit
Clear Key Reduce key,
right key, and
select the last
parameter
Tare Add key, left
key, and
select the
next
parameter
Short press
switch display
channel, long
press enter
setting menu
Confirm input
value. Confirm
exit
Cursor indication
Functionality
PLC
Indicates the communication status of ModbusRTU、ModbusTCP、
Profinet
flicker：offline,
light：ModbusRTU、ModbusTCP、Profinet
. At least one communication
is normal
>0< Light：Scale in center ofzero(±1/4 division)
~ Light：Scale in motion mode
Net ON：Scale in Net Mode
1、2、3、4 The currentdisplay and indicator represent channel number
Not bright: no Bluetooth module installed
flicker: Bluetooth waiting for connection
light: Bluetooth Connected

ID551PN Weighing Controller
6
2.2 Top Menu
2.3 Setup
2.3.1 1#Channel Scale
[1.1 ] Increment Size
0 (0.001), 1 (0.002), 2 (0.005), 3(0.01),4(0.02), 5(0.05),
6 (0.1), 7 (0.2), 8 (0.5), 9(1), 10 (2), 11 (5),
12 (10), 13 (20), 14 (50), 15 (100)
[1.2 ] Capacity
Sets the maximum weighing of the scales,with default value 60
[1.3 ] Calibration Mode
2-P：two point calibration mode ,Only support [1.4 ] (Zero Point)& [1.6 ] (End
Point
[F1] 1#Scale Configuration
)
CALFr E：calibration without weighing added
[1.4 ] Zero Point Adjustment
See appendix1.
[1.6 ] End-Point Calibration
See appendix1.
[1.7] CalFree Block
[1.7.1] Load Cell Capacity
Input the load cell capacity
[1.7.2] Number of total load cells
Input total number of load cells in this scale
[Setup]
Menu
[F2] 2#Scale Configuration
[F3] 3#Scale Configuration
[F4] 4#Scale Configuration
[F10]Maintenance
Pre ss Print Key for 2 se conds
[F9]Network
[- - - -]
If have a
password,
please enter
password
[F6]Serial Port

ID551PN Weighing Controller
7
[1.7.3] Number of working load cells
Input the number of working load cells inthis scale
[1.7.4 ] Load Cell Sensitivity
Input the sensitivity of load cell, in general, It is 2mV/V or 3mV/V
[1.7.5 ] Sensitivity calibration
Atest weight is loaded to calibrate thesensorsensitivity,and the method reference End Point
[1.8 ] Filter
0(lowest)，1，2，3，4，5，……18，19(Highest)
[1.9 ] Pushbutton Zero Range
0– Disable Pushbutton Zero
2，5，10，
20，30，40，50：zero scale range is 2%，5%，10%，20%，30%，
40%，50% of capacity
[1.10 ] Motion Check
[1.A ]
[1.A.1 ] : View zero adjustmentADC code
[1.A.2 ] : View span adjustment ADC code
[1.A.3 ] : Viewspan adjustment weight value
[1.A.4 ] : Change or Enter zero adjustmentADC code
[1.A.5 ] : Change or Enter span adjustmentADC code
[1.A.6 ] : Change or Enter zero adjustment weight value
[3.0d]
0–Disable motion check 0.1~9.9 –Enable motion check
[1.11 ] Auto Zero Range
0–Disable Auto Zero
0.1~9.9 - 0.1d - 9.9d, Enable
When set to >0, the auto zero tracking is within ±10d
[1.12 ] Auto Zero Speed
0– Disable Auto Zero
0.1~9.9 - Enable Auto Zero, Speed is(0.1~9.9)d/second
[1.13 ] Tare
0– Disable Tare
1–Enable Tare
[1.14 ] Application Mode
0– Weight mode
1–Dynamometry mode

ID551PN Weighing Controller
8
2.3.2 2#Channel Scale
[2.1 ] Increment Size
0 (0.001), 1 (0.002), 2 (0.005), 3(0.01),4(0.02), 5(0.05),
6 (0.1), 7 (0.2), 8 (0.5), 9(1), 10 (2), 11 (5),
12 (10), 13 (20), 14 (50), 15 (100)
[2.2 ] Capacity
Sets the maximum weighing of the scales,with default value 60
[2.3 ] Calibration Mode
2-P：two point calibration mode ,Only support [2.4 ] (Zero Point)& [2.6 ] (End
Point)
CALFr E：calibration without weighing added
[2.4 ] Zero Point Adjustment
See appendix1.
[2.6 ] End-Point Calibration
See appendix1.
[2.7 ] CalFree Block
[2.7.1 ] Load Cell Capacity
Input the load cell capacity
[2.7.2 ] Number of total load cells
Input total number of load cells in this scale
[2.7.3 ] Number of working load cells
Input the number of working load cells inthis scale
[2.7.4 ] Load Cell Sensitivity
Input the sensitivity of load cell, in general, It is 2mV/V or 3mV/V
[2.7.5 ] Sensitivity calibration
Atest weight is loaded to calibrate thesensorsensitivity,and the method reference End Point
[2.8 ] Filter
0(lowest)，1，2，3，4，5，……18，19(Highest)
[2.9 ] Pushbutton Zero Range
0– Disable Pushbutton Zero
2，5，10，
20，30，40，50：zero scale range is 2%，5%，10%，20%，30%，
40%，50% of capacity
.
[2.10 ] Motion Check [3.0d]
0–Disable motion check 0.1~9.9 –Enable motion check

ID551PN Weighing Controller
9
[2.11 ] Auto Zero Range
0–Disable Auto Zero
0.1~9.9 - 0.1d - 9.9d, Enable
When set to >0, the auto zero tracking is within ±10d
[2.12 ] Auto Zero Speed
0–Disable Auto Zero
0.1~9.9 - Enable Auto Zero, Speed is(0.1~9.9)d/second
[2.13 ] Tare
0– Disable Tare
1–Enable Tare
[2.14 ] Application Mode
0– Weight mode
1–Dynamometry mode
[2.A ]
[2.A.1 ] : View zero adjustmentADC code
[2.A.2 ] : Viewspan adjustmentADC code
[2.A.3 ] : Viewspan adjustment weight value
[2.A.4 ] : Change or Enter zero adjustmentADC code
[2.A.5 ] : Change or Enter span adjustmentADC code
[2.A.6 ] : Change or Enter zero adjustment weight value
2.3.3 3#Channel Scale
[3.1 ] Increment Size
0 (0.001), 1 (0.002), 2 (0.005), 3(0.01),4(0.02), 5(0.05),
6 (0.1), 7 (0.2), 8 (0.5), 9(1), 10 (2), 11 (5),
12 (10), 13 (20), 14 (50), 15 (100)
[3.2 ] Capacity
Sets the maximum weighing of the scales,with default value 60
[3.3 ] Calibration Mode
2-P：two point calibration mode ,Only support [3.4 ] (Zero Point)& [3.6 ] (End
Point )
CALFr E：calibration without weighing added
[3.4 ] Zero Point Adjustment
See appendix1.
[3.6 ] End-Point Calibration
See appendix1.

ID551PN Weighing Controller
10
[3.7 ] CalFree Block
[3.7.1 ] Load Cell Capacity
Input the load cell capacity
[3.7.2 ] Number of total load cells
Input total number of load cells in this scale
[3.7.3 ] Number of working load cells
Input the number of working load cells inthis scale
[3.7.4 ] Load Cell Sensitivity
Input the sensitivity of load cell, in general, It is 2mV/V or 3mV/V
[3.7.5 ] Sensitivity calibration
Atest weight is loaded to calibrate thesensorsensitivity,and the method reference End Point。
[3.8 ] Filter
0(lowest)，1，2，3，4，5，……18，19(Highest)
[3.9 ] Pushbutton Zero Range
0– Disable Pushbutton Zero
2，5，10，
20，30，40，50：zero scale range is 2%，5%，10%，20%，30%，
40%，50% of capacity
[3.10 ] Motion Check [3.0d]
0–Disable motion check 0.1~9.9 –Enable motion check
[3.11 ] Auto Zero Range
0–Disable Auto Zero
0.1~9.9 - 0.1d - 9.9d, Enable
When set to >0, the auto zero tracking is within ±10d
[3.12 ] Auto Zero Speed
0–Disable Auto Zero
0.1~9.9 - Enable Auto Zero, Speed is(0.1~9.9)d/second
[3.13 ] Tare
0– Disable Tare
1–Enable Tare
[3.14 ] Application Mode
0– Weight mode
1–Dynamometry mode
[3.A ]
[3.A.1 ] : View zero adjustmentADC code
[3.A.2 ] : Viewspan adjustmentADC code
[3.A.3 ] : Viewspan adjustment weight value