Tupex Hydroway Medium 01 Square LED User manual

ASSEMBLY AND OPERATING INSTRUCTIONS:
-Power consumption : 20W
-Voltage :220/240V 50/60Hz
-Color Temperature : 000K
-Lumen output: 1200lm
-Lens Type : 4X85° beam
-Insulation class: 1
-IP protection: IP65
-Gross weight: .8kg
COD. 603005
COD. 603006
COD. 603005
-Power consumption : 20W
-Voltage :220/240V 50/60Hz
-Color Temperature : 000K
-Lumen output: 1200lm
-Lens Type : 60° beam
-Insulation class: 1
-IP protection: IP65
-Gross weight: 5.2kg
COD. 603006
380mm 680mm
Made in Italy
-replace the damaged protective glass
-glass features: plane float glass - safety tempered
-getting rid of as urban waste forbidden
-separate collection is mandatory when the product is at the
end of its life
- -Class I fitting electric gruonding is needed
-Complete protection from dust and water jets
IP65
150X150mm
NB: These assembly instructions must be given to end users for correct maintenance and so that they know how to change the bulb.
The a liance must not be tam ered with or transformed and it must be installed and used as su lied and in com liance with the
National Rules on Installations. Any non-com liant installations will invalidate all forms of guarantee. The com any cannot be held
res onsible for damage caused by incorrect assembly.
THE WARRANTY IS FALLING IN THE FOLLOWING CASES:
1) Malfunctions due to improper use of the product, modifications, repairs inadeguate, negligence on the part of the
installer electrician, failure to assembly instructions and or data plate;
2) Installations in plants not comply with the general safety;
3) Damage caused by natural causes such as lightning, fire or flooding;
4) Damage caused by wiring connections with IP degree lower than the selected product.
5) Damage occurring during shipment of the product. In these cases the damage will be to charge and notify the car-
rier;
6) The warranty covers only the integrity of the product and NOT any costs of removal of the same;
150X150mm

Recommendations
1) verify that the equipment used to connect our devices to enjoy
all the guarantees required under European law;
2) use the cables, connectors and quality materials for electrical wiring;
3) Products with IP65 68 degree make the wiring connections with accessories
provide the same degree IP of the selected product (available in the catalog);
4) In the case of installations outside is not recommended to install the power supplies in the
formwork and or in the junction box without adequate protection
Relam ing and maintenance:
-The relamping must be done with maximum attention avoiding to dirty the sealing gasket and its contact surface. It is therefore
necessary before
opening the fixture to carefully wipe the floodlight then unscrew the round frame by the proper key
-If the gasket is damaged, deformed or not in perfect conditions it is necessary to change it
-it is essential to do a frequent cleaning of the glass and of the outer surface of the fixture to avoid build up of mud and dirtiness
resulting in dangerous
overheating due to uncorrect light and heat dissipation. Clean carefully the glass screen removing limestone deposits by means of a
scraper.
.The re lacement must be done by a qualified electrician.
INSTALLATION:
-SWITCH-OFF THE POWER SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE OPERATION
-1 Open the luminaire uncsrewing three screws using the hexagonal tool including in the package
-2 Prepare holes in the floor in correspondance of the feeding point using plugs type ficher (not included in the package)
-3 Fix the base to the floor by tighten the screws of the plugs
-4 Open the upper head of the luminaire uscrewing four screws using the hexagonal tool
-5 Insert the cable through the bottom rubber cable gland and move the cable into the cylindert to the cable connector
-6 Make the electrical connection to the terminal.
-7 Remount the luminaire tighten the 6 nuts using the hexagonal tool.
3
2
1 6
5
4
FIXING HOLES

Fixing base accessory