TW Audio WHF User manual

Assembly
Instructions
WHF

Assembly Instructions WHF
2
Introduction
Instructions in this user manual
WARNING
The wall mount flat WHF is an accessory for the B14i loudspeaker.
It is characterized by a subtle look, a remarkable size to weight ratio and ease of use.
Thank you for choosing a high-quality product “MADE IN GERMANY” from the brand
TW AUDiO.
If you lend your product to another party, inform that party of the safety-related operating pro-
cedures and hand over this assembly guide. If you require additional copies of this manual,
you can obtain them free of charge from TWAUDiO or download them from www.twaudio.de
Strictly adhere to the instructions contained in this operating manual that are marked as
follows:
This symbol in combination with the signal word “Warning” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to serious injury or even death.
This symbol in combination with the signal word “Caution” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to light or moderate injury.
This symbol in combination with the signal word “Note” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to product damage.
This symbol in combination with the signal word “Tip” identifies additional information or
notes that will simplify working with TWAUDiO products on the basis of practical experience.
CAUTION
NOTE
TIP

Assembly Instructions WHF
3
Notes on the products
Read manual
before use!
General information
Assembly instructions: OM-WHF
Version 2.0 en, 03/2023
© by TWAMBO 2023; all rights reserved.
All information contained in this operating manual was correct to the best of our knowledge
at the time of printing.
Quality warranties or assurance of suitability for a certain type of use based on the technical
specifications, dimensions and weights are not granted by TWAMBO.
TWAMBO also shall not assume liability for any secondary damage (property damage and/or
personal injury) nor for the failure to comply with this operating manual!
TWAMBO reserves the right to update this document based on recent developments.
TWAMBO GmbH
Karl-Hofer-Str. 42
14163 Berlin
Germany
Phone : + 49 (0) 71 41-48 89 89 0
Fax: + 49 (0) 71 41-48 89 89 99
E-Mail: [email protected]
WWW: www.twaudio.de
Before using the device, carefully read the assembly instructions and keep it with the
WHF wall mount flat.

Assembly Instructions WHF
4
Content
1. Safety | Intended use...................................................................................................... 5
2. Overview ........................................................................................................................ 7
2.1 Components ........................................................................................................... 7
3. Technical data ................................................................................................................ 8
3.1 Data sheet............................................................................................................... 8
3.2 Description of the plates from the scope of delivery ................................................. 8
4. Commissioning............................................................................................................... 9
4.1 Setup ...................................................................................................................... 9
4.2 Necessary tools for setting up the flown system ...................................................... 9
4.3 Preparing the B14i loudspeaker............................................................................. 10
4.4 Preparing the WHF wall mount flat......................................................................... 12
4.5 Mounting the speaker plate to the B14i loudspeaker ............................................. 13
4.6 Mounting the centering as well as pressure plate to the B14i loudspeaker............. 14
4.7 Mounting the wall plate to different construction forms of a wall............................. 15
4.8 Hang loudspeaker on wall ..................................................................................... 16
4.9 Screwing the plates of the WHF............................................................................. 17
5. Transport and storage .................................................................................................. 18
6. CE Conformity Declaration............................................................................................ 19
7. Disposal ....................................................................................................................... 19

Assembly Instructions WHF
5
1. Safety | Intended use
WARNING
WARNING
WARNING
WARNING
WARNING
CAUTION
The WHF wall mount flat was developed for use in professional sound systems. The
wall mount slim may only be used by trained and qualified personnel.
Please adhere to the following safety instructions to avoid risks when using accessories.
Note the operating modes described in this assembly instructions. Other uses are not per-
missible.
Damage caused by improper use is not covered by TWAMBO.
Before every operation, check the scope of delivery of the WHF wall mount flat for its com-
pleteness and ensure that all parts are in perfect condition.
The scope of delivery includes specified components. Only use the recommended and cer-
tified components.
The WHF wall mount flat may only used with the B14i loudspeaker.
This rigging manual describes how to use the WHF wall mount flat correctly. Any other use
shall be deemed improper and may result in damage or even injury.
Modifications or alterations to individual parts of the WHF wall mount flat are not permitted!
Danger to life!
The WHF wall mount flat is designed for indoor use.
The WHF wall mount flat may only be used by trained and qualified personnel. Personnel
must check the WHF wall mount flat for suitability before each use.
The WHF wall mount flat must be taken out of operation immediately as soon as visible
damage to the parts can be seen.
Please keep all elements of the WHF wall mount flat away from children! The small parts can
easily be swallowed and lead to suffocation!

Assembly Instructions WHF
6
WARNING
WARNING
WARNING
WARNING
WARNING
CAUTION
The payload of the WHF wall mount flat is designed of not more than one B14i loudspeaker.
Do not exceed this payload.
Make sure that no water pipes, electrical lines or any other lines are behind the intended place
of mounting.
Only use wall plugs and screws which are suitable for the intended mounting and structural
fabric. All screws must be set and tightened properly. Ensure that the fixing holes have the
correct depth and diameter. Always use all fixing holes.
Before mounting the WHF wall mount flat check that walls are capable to carrying the pay-
load of the components.
When moving (assembling, dismantling, maintaining) the WHF wall mount flat with
B14i loudspeaker, ensure sufficient space to prevent collisions with other objects.
Do not squeeze or twist the electrical cables of the B14i loudspeaker during the installation
of the WHF wall mount flat! The respective national electrotechnical rules and regulations are
applicable.

Assembly Instructions WHF
7
2. Overview
2.1 Components
Figure 2.1 - Overview
1. Hexagon head screw M10 x 30.........................................................................1 piece
2. Pan head screw with flange M6 x 18 ............................................................... 4 pieces
3. Pan head screw without flange M6 x 16 .......................................................... 2 pieces
4. Pressure plate ................................................................................................... 1 piece
5. Centering plate..................................................................................................1 piece
6. Sheet metal for mounting on wall.......................................................................1 piece
7. Sheet metal for mounting on loudspeaker ......................................................... 1 piece
123
45
6 7

Assembly Instructions WHF
8
3. Technical data
Maximum load capacity 1x B14i
Dimensions (h x w x d) 232 x 275 x 21 mm [9.13 x 10.83 x 0.83 in]
Weight 1,7 kg [3.75 lbs]
Surface Powder-coated
3.1 Data sheet
Note that generalized throughout the manual the two plates from the scope of delivery are
called:
• Pos.6: Sheet metal for mounting on wall as wall plate
and
• Pos.7: Sheet metal for mounting on loudspeaker as loudspeaker plate.
3.2 Description of the plates from the scope of delivery
NOTE

Assembly Instructions WHF
9
4. Commissioning
4.1 Setup
The WHF wall mount flat is designed for hanging operation on walls.
Please note that setting up the system structures always requires two persons!
WARNING
TW AUDiO recommends using only the accessories specified by TWAUDiO for securing and
mounting the wall mount slim.
Whenever you make changes to the flown system, always use a new hexagon head screw
(item 1 on scope of delivery) and pan head screws (item 2 and 3 on scope of delivery) as
delivered with the product.
These items are available from TW AUDiO.
NOTE
WARNING
4.2 Necessary tools for setting up the flown system
• Torque wrench
• Extension for bit insert, min. 150 mm [min. 5,9 in]
• Bit insert for torque wrench: TX30
• Bit insert for torque wrench: TX50
• SW17 fork wrench
Keep the following tools ready for assembling the flown systems:

Assembly Instructions WHF
10
4.3 Preparing the B14i loudspeaker
Remove the M10 screw at the B14i loudspeaker.
Figure 4.3.1 - Remove the M10 screw
NOTE

Assembly Instructions WHF
11
Figure 4.3.2 - Remove the M6 screws
Then remove the four M6 screws from the B14i loudspeaker.
NOTE

Assembly Instructions WHF
12
4.4 Preparing the WHF wall mount flat
Figure 4.4.1 - Remove the two screws
Remove the two screws at the WHF wall mount flat.
Figure 4.4.2 - Remove sheet metal
Remove the loudspeaker sheet metal.
NOTE
NOTE

Assembly Instructions WHF
13
4.5 Mounting the speaker plate to the B14i loudspeaker
Attach the loudspeaker plate (see figure 2.1, item 7) of the WHF wall mount flat to the
B14i loudspeaker. Use the pan head screws with flange (see figure 2.1, item 2) from our
scope of delivery.
Tighten the screw sufficiently! (18Nm)
Figure 4.5 - Attach loudspeaker plate at loudspeaker
WARNING

Assembly Instructions WHF
14
4.6 Mounting the centering as well as pressure plate to the B14i loudspeaker
1. First place the centering plate (see figure 2.1, item 5) into the large center hole of the
loudspeaker plate that is already attached to the B14i loudspeaker.
2. Place the pressure plate on top (see figure 2.1, item 4) and screw the two plates together
using the hexagon head screw (see figure 2.1, item 1).
3. Tighten the screw sufficiently! (18Nm)
Figure 4.6 - Attach centering plate and pressure plate to the loudspeaker
WARNING

Assembly Instructions WHF
15
4.7 Mounting the wall plate to different construction forms of a wall
In addition, observe the following instructions for attaching the wall plate
(see figure 2.1, item 6):
1. To fix the wall plate to a concrete or brick wall, use the BZ holes (see figure 4.7). Make sure
that all four mounting holes BZ are used!
2. To fix the wall plate to a lightweight wall, use the holes L (see figure 4.7). Make sure that
all three mounting holes L are used!
When attaching the wall plate (see figure 2.1, item 6), follow the instructions from
chapter 1 - Safety / Intended use.
BZ BZ
BZBZ
L
L
L
Wall
Figure 4.7 - Hole descriptions
WARNING
WARNING

Assembly Instructions WHF
16
4.8 Hang loudspeaker on wall
Carefully insert the loudspeaker plate on the B14i loudspeaker into the wall plate attached to
the wall.
Figure 4.8 - Insert loudspeaker plate with loudspeaker into wall plate
WARNING

Assembly Instructions WHF
17
4.9 Screwing the plates of the WHF
Screw the two plates of the WHF wall mount flat using the two pan-head screws
(see Figure 2.1, item 3). Use an extension for the bit insert for this purpose.
Figure 4.9 - Setting the screws
135
WARNING

Assembly Instructions WHF
18
5. Transport and storage
Ensure that the surfaces of the parts of the wall mount flat are not damaged during transport
and storage. Moisture may penetrate where steel surfaces are exposed by scratches and
result in corrosion.
This is why the products should be transported in a safe, careful, dry and largely dust-free
manner.
NOTE

Assembly Instructions WHF
19
7. Disposal
6. CE Conformity Declaration
If you have any question regarding the disposal of used devices, please contact us under the
following telephone number:
+49 (0) 71 41 - 48 89 89 0
In countries outside of the European Union, comply with local regulations.
as well as all model variants based on these, provided that they correspond to the original
factory models and have not been technically modified in any way.
Applicable directives:
• 2001/95/EG
Applicable national standards and technical specifications:
• DIN EN 18 800
• DIN EN ISO 12 100
• DGUV Vorschrift 17 und 18
Berlin, Germany, January 1st, 2021
Bernhard Wüstner
This declaration applies to the following components
• WHF
Copy and translation of the original CE Conformity Declaration:
We hereby declare that the below-referenced components by virtue of their design and con-
struction, and in the configuration placed on the market by us, satisfy the safety and health
requirements of the applicable EC directives. This declaration becomes invalid in case of modi-
fications that have not been approved by us.

Assembly Instructions WHF
20
TWAMBO GmbH
Karl-Hofer-Str. 42
14163 Berlin
Germany
Phone: + 49 (0) 71 41-48 89 89 0
Fax: + 49 (0) 71 41-48 89 89 99
E-Mail: [email protected]
WWW: www.twaudio.de