Twister R/C User manual

2.4GHZ COMPUTER RADIO
OPERATION MANUAL
V11.10

2
Warranty conditions
J. Perkins Distribution Ltd. guarantee this product to be free of manufacturing and assembly defects for a period of one
year from time of purchase and Model Engines Pty Ltd. for 30 days. This does not affect your statutory rights. This warranty
is not valid for any damage or subsequent damage arising as a result of a crash, misuse, modification or for damage or
consequential damage arising as a result of failure to observe the procedures outlined in this manual. Operation of this
model is carried out entirely at the risk of the operator. Please note that, whilst every effort is made to ensure the accuracy
of instructions and material included with this product, mistakes can occur and neither J. Perkins Distribution Ltd/Model
Engines (Aust.) Pty. Ltd. nor it’s distributors will be held liable for any loss or damage arising from the use of this model or
for any loss or damage arising from omissions or inaccuracies in the associated instructions or materials included with this
product.
We reserve the right to modify the design of this product, contents and manuals without prior notification.
© 2010 J Perkins Distribution Ltd, Lenham, Kent, UK ME17 2DL.
www.jperkinsdistribution.co.uk
Model Engines (Aust.) Pty. Ltd., Noble Park, Victoria 3174, Australia. www.modelengines.com.au. All rights reserved. E&OE.
EU rEgUlations
J Perkins Distribution Ltd declares that this remote control system is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC on Radio equipment and Telecommunications Terminal Equipment. A copy
of the declaration(s) of conformity can be obtained from J Perkins Distribution Ltd, Ashford rd, Lenham, Kent. UK ME17 2DL.
This system complies with the EU directive on Waste Electrical and Electronic Equipment. Do not dispose of this product
in household waste. At the end of the products’ life, dispose of it at a designated collection point for the recycling of waste
electrical and electronic equipment.
Please contact your supplier for any advice required on disposal.
contEnts
TRANSMITTER LAYOUT ............................. 4
CONTROL LAYOUT (MODE 1).................................................4
CONTROL LAYOUT (MODE 2).................................................5
CONTROL LAYOUT (MODE 1) ..................... 6
MODEL MEMORY ...................................... 7
PROGRAMMING IN HELI MODE ................. 8
SERVO REVERSING .................................................................8
DUAL RATE................................................................................8
SUB TRIM..................................................................................9
TRAVEL ADJUST ......................................................................9
SW– TYP ...................................................................................9
THR-CUR (NORMAL) .............................................................10
THR-CUR (IDLE UP) (NORMAL) ...........................................10
PIT-CUR (NORMAL) ...............................................................10
PIT-CUR (IDLE UP) .................................................................11
PIT-CUR (THROTTLE HOLD)..................................................11
HLD-ON/OFF............................................................................11
EXIT PROGRAMMING MODE ..............................................11
PROGRAMMING IN AERO MODE.............. 12
SERVO REVERSING ...............................................................12
DUAL RATE..............................................................................12
SUB TRIM................................................................................13
TRAVEL ADJUST ....................................................................13
AIL-FLP ....................................................................................13
AIL-ELE ....................................................................................14
ELE-RUD ..................................................................................14
ELE-AIL ....................................................................................14
RUD-ELE ..................................................................................14
THR-CUR (NORMAL) .............................................................15
EXIT PROGRAMMING MODE ..............................................15

3
introdUction
Thank you for purchasing Twister 2.4GHz computer
radio control system. It is designed for remotely
operating R/C model aircraft safely in the easiest
possible manner without the need for crystals.
It’s uncomplicated yet sophisticated design makes
it an ideal first system or a general purpose sport
system for R/C modelling.
It uses state-of-the-art computer technology
to bind it’s transmitter and receiver in such a
fashion that, under most model flying conditions,
interference that would normally cause loss of
control in 35MHz or 27MHz equipment is nearly
always rejected—and in most cases radio
functionality is entirely unaffected. This makes for
a safer, more reassuring flying experience.
It also enables a pilot to turn up, switch on and
fly under most conditions—subject to local flying
guidelines and rules.
safEty information
WARNING!
This equipment must be assembled carefully
into an appropriate R/C aircraft according to the
manufacturers’ recommendations.
Note that Twister 2.4GHz computer radio is not
a ‘full range’ system and must only be used with
small Park Flyer/ helicopter R/C models operated
at relatively short range (around 150 metres).
This product is a sophisticated control system for
model aircraft and is not a toy. Suitable only for
persons aged 14+
Check all radio equipment carefully before use
and range check before every flight.
Never fly near people, animals, buildings, power
lines, water or trees.
Ensure that all batteries are either fresh (if
alkaline) or charged (if rechargeable) before
using this equipment.
In the UK we recommend you observe BMFA
safety codes at all times when operating radio
controlled models.
This equipment is designed to be installed
and used only within a radio control hobby
environment.
2.4GHz signals are less tolerant of obstacles so
never fly close to structures, trees, hedges which
if flown behind may cause a temporary loss of
signal.
Never fly in rain.
UK air laW, Bmfa & safEty
All model aircraft operated in the UK are subject
to UK Air Law. It should be noted that in the UK
a considerable burden of responsibility and a
strict duty of care lie with the pilot of any model
aircraft. Under UK Air Law the pilot assumes all
responsibility for his aircraft.
Radio control model aircraft are potentially
capable of inflicting severe personal injury or
even death to people or animals and can cause
considerable damage to property if operated
incorrectly or irresponsibly.
In the UK, the British Model Flying Association
(BMFA) (http://www.bmfa.org) is responsible for
overseeing all aspects of model flying.
If you are new to R/C modelling we strongly
recommend you download the BMFA handbook
(http://www.bmfa.org/handbook/index.html) which
contains much useful information about model
flying including legal, insurance, safety obligations
and technical recommendations for model pilots.
not What yoU ExpEctEd?
If the information presented in the preceding
paragraphs and opposite is not what you expected
and you either cannot or choose not to accept
the responsibilities associated with operating this
equipment in a model in the UK, you should not buy
this product.
In the event you have already purchased this
product; you should return the product in it’s
original condition and obtain a refund from your
supplier.

4
transmittEr layoUt
CONTROL LAYOUT (MODE 1)
1
2 10
11
12 16
13 14
15
3
4
56
17 19
18 20
7
89
1. Elevator Control
2. Rudder Control
3. Elevator Dual Rate Switch
4. Rudder Dual Rate Switch
5. Throttle Hold Switch
6. Trainer Switch
7. 3D/Aerobatic Switch (Idle Up)
8. Gyro Mode Selector Switch (Heli)/Retractable Landing Gear Switch (Aircraft)
9. Aileron Dual Rate Switch
10. Aileron Control
11. Throttle Control
12. Rudder Trim Lever
13. Elevator Trim Lever
14. Throttle Trim Lever
15. On/Off Power Switch
16. Aileron Trim Lever
17. INC Button for increasing values during programming
18. DEC Button for decreasing values during programming
19. MAIN_Menu Button for changing Main Menu Categories during programming
20. SUB_Menu Button for scrolling within Main Menu categories during programming

5
CONTROL LAYOUT (MODE 2)
1
2 10
11
12 16
13 14
15
3
4
56
17 19
18 20
7
89
1. Throttle Control
2. Rudder Control
3. Elevator Dual Rate Switch
4. 3D/Aerobatic Switch (Idle Up)
5. Trainer Switch
6. Throttle Hold Switch
7. Rudder Dual Rate Switch
8. Gyro Mode Selector Switch (Heli)/Retractable Landing Gear Switch (Aircraft)
9. Aileron Dual Rate Switch
10. Aileron Control
11. Elevator Control
12. Rudder Trim Lever
13. Throttle Trim Lever
14. Elevator Trim Lever
15. On/Off Power Switch
16. Aileron Trim Lever
17. INC Button for increasing values during programming
18. DEC Button for decreasing values during programming
19. MAIN_Menu Button for changing Main Menu Categories during programming
20. SUB_Menu Button for scrolling within Main Menu Categories during programming

6
control layoUt (modE 1)
Trainer Cord Socket
Charging Jack for charging
rechargeable Ni-Mh batteries
IMPORTANT:
THE CENTRE PIN OF THE CHARGING
JACK IS NEGATIVE!
Use of the incorrect charger could
severely damage the radio and
batteries.
Battery compartment for 8 x AA size batteries.
Re-chargeable Ni-Mh can be used.

7
modEl mEmory
■To set up a new model memory or select a model from memory.
■Access by pressing both MAIN_MENU & SUB_MENU then tuning on the power switch.
■The display will show the TYPE, HELI or AIR by
the arrow.
■Press the INC or DEC buttons to switch
between HELI or AIR mode.
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■Press INC or DEC to select one of the 4 model
memories
Note: There are 4 model memories for Heli and 4
model memories for Air mode.
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■Press INC or DEC to choose between YES or
NO
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■To confirm reset press MAIN_MENU & SUB_
MENU together
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■Press INC or DEC to electronically set the
throttle to mode-1 “R” or mode-2 ”L”.
■Press INC or DEC to change the character
value
■Press SUB_MENU to move to the next
character
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■This setting is only available in HELI mode.
■Press INC or DEC to choose between CCPM or
NOR.
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
Main menu
Main menu
Main menu
Main menu
Main menu
Main menu
Main
menu
■Press MAIN_MENU and SUB_MENU together to confirm and exit.

8
programming in hEli modE
Press ‘MAIN_MENU’ & ‘SUB_MENU’ buttons
together to enter Programming Mode.
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
SERVO REVERSING
■The first Menu Category is the Servo
Reversing Menu.
■Select the servo or function to be reversed by
using the ‘SUB_Menu’ button.
NOTE the position of the arrow. This indicates the
servo or function to be affected.
CH. 1 - Throttle
CH. 2 - Aileron
CH. 3 - Elevator
CH. 4 - Rudder
CH. 5 - Gyro/Gear Switch
CH. 6 - Flap
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■To change the servo direction, press and hold
either the ‘INC’ or ‘DEC’ button for at least 2
seconds, then release.
■The screen will change from ‘OFF’ to ‘ON’
or from ‘ON’ to ‘OFF’ depending on which
direction the servo is required to rotate.
DUAL RATE
■Select the next Menu Category by pressing the
‘MAIN_MENU’ button.
■The next Menu Category is ‘Dual Rate’.
■NOTE that only CH. 2 (Aileron), CH. 3 (Elevator)
& CH. 4 (Rudder) have Dual Rate facilities.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■Use the Dual Rate Switches on the transmitter
to toggle between the High and Low rate
settings.
■Use the ‘INC’ and ‘DEC’ buttons to make any
adjustments.

9
■Use the ‘SUB_MENU’ button to scroll through
to the next CH or function.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
SUB TRIM
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■The next Menu Category is the ‘Sub Trim’.
■The Sub Trim is used to fine tune the centre
point of the servo.
■Use the ‘SUB_MENU’ button to scroll through
to the next CH or function.
TRAVEL ADJUST
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■Press the ‘MAIN_MENU’ button to move to
the ‘TRV-ADJ’ (Travel Adjust) menu.
■This allows the total throw or movement of the
servo to be adjusted.
■Both ends of the servo travel can
be adjusted.
■To do so, move the appropriate
control stick in the direction that
requires adjustment.
■Use the ‘INC or ‘DEC’ button to
make any changes.
HELI AIR NOR IDLE NAME RST
CH1/L
CH2/1
CH3/2
CH4/3
CH5/H
CH6
INC
DEC
MAIN_MENU
SUB_MENU
POWER
ON
HELI AIR NOR IDLE NAME RST
CH1/L
CH2/1
CH3/2
CH4/3
CH5/H
CH6
INC
DEC
MAIN_MENU
SUB_MENU
POWER
ON
SW– TYP
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■This menu is used to individually adjust the
three CCPM servos (CH. 2, CH. 3 & CH. 6)for
both the control throw and direction.
■Use the ’SUB_MENU’ button to scroll through
to each servo.
■Use the ’INC’ & ’DEC’ buttons to adjust the
values.
■To change direction, use the ‘INC’ or ‘DEC’
button and scroll past ‘zero’.
■This will give a + or - value depending on the
direction required.

10
THR-CUR (NORMAL)
■The next Menu or Category is the THR-CUR
(Throttle Curve) menu for ‘Normal’ or ‘Hover’
mode.
■NOTE the arrow pointing to ‘NOR’
■The throttle curve has 5 adjustable points.
■Use the ‘SUB_MENU’ button to scroll down to
each of the 5 points. CH1/L being the low point
and CH5/H being the high or 5th point on the
curve.
■Use the ‘INC’ & ‘DEC’ to change the values.
This shows the low point of the throttle curve in
Normal or Hover mode.
This shows the high point of the throttle curve in
Normal or Hover mode.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
THR-CUR (IDLE UP) (NORMAL)
This shows the low point of the throttle curve in
Idle Up or 3D mode.
■The next Menu or Category is the THR-CUR
(Throttle Curve) menu for ‘Idle Up’ or ‘3D’
mode.
■NOTE the arrow pointing to ‘IDLE’.
■The throttle curve has 5 adjustable points.
■Use the ‘SUB_MENU’ button to scroll down to
each of the 5 points. CH1/L being the low point
and CH5/H being the high or 5th point on the
curve.
■Use the ‘INC’ & ‘DEC’ to change the values.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
PIT-CUR (NORMAL)
This shows the low point of the pitch curve in
Normal or Hover mode.
■The next Menu or Category is the PIT-CUR
(Pitch Curve) menu for ‘Normal’ or ‘Hover’
mode.
■NOTE the arrow pointing to ‘NOR’
■The Pitch Curve has 5 adjustable points.
■Use the ‘SUB_MENU’ button to scroll down to
each of the 5 points. CH1/L being the low point
and CH5/H being the high or 5th point on the
curve.
■Use the ‘INC’ & ‘DEC’ to change the values.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)

11
PIT-CUR (IDLE UP)
This shows the low point of the pitch curve in Idle
Up or 3D mode.
■The next Menu or Category is the PIT-CUR
(Pitch Curve) menu for ‘Idle Up’ or ‘3D’ mode.
■NOTE the arrow pointing to ‘IDLE’.
■The Pitch Curve has 5 adjustable points.
■Use the ‘SUB_MENU’ button to scroll down to
each of the 5 points. CH1/L being the low point
and CH5/H being the high or 5th point on the
curve.
■Use the ‘INC’ & ‘DEC’ to change the values.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
PIT-CUR (THROTTLE HOLD)
This shows the low point of the pitch curve in
Throttle Hold mode.
■The next Menu or Category is the PIT-CUR
(Pitch Curve) menu for ’Throttle Hold’ or ‘Auto
rotation’ mode.
■NOTE the arrow pointing to ‘Hold_ON/CCPM’.
■The Pitch Curve has 5 adjustable points.
■Use the ‘SUB_MENU’ button to scroll down to
each of the 5 points. CH1/L being the low point
and CH5/H being the high or 5th point on the
curve.
■Use the ‘INC’ & ‘DEC’ to change the values.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HLD-ON/OFF
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■The final Menu or Category is the HLD menu.
■This is used to activate or de-activate the
Throttle Hold (Auto Rotation) function.
■To activate or de-activate the Throttle Hold
function, press the ’SUB_MENU’ button.
■When the Throttle Hold function is
activated, use the ‘INC’ and ‘DEC’ buttons to
fine tune the idle position.
EXIT PROGRAMMING MODE
Press ‘MAIN_MENU’ & ‘SUB_MENU’ buttons
together to exit Programming Mode.
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)

12
programming in aEro modE
Press ‘MAIN_MENU’ & ‘SUB_MENU’ buttons
together to enter Programming Mode.
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
SERVO REVERSING
■The first Menu Category is the Servo
Reversing Menu.
■Select the servo or function to be reversed by
using the ‘SUB_Menu’ button.
NOTE the position of the arrow. This indicates the
servo or function to be affected.
CH. 1 - Throttle
CH. 2 - Aileron
CH. 3 - Elevator
CH. 4 - Rudder
CH. 5 - Gyro/Gear Switch
CH. 6 - Pitch
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■To change the servo direction, press and hold
either the ‘INC’ or ‘DEC’ button for at least 2
seconds, then release.
■The screen will change from ‘OFF’ to ‘ON’
or from ‘ON’ to ‘OFF’ depending on which
direction the servo is required to rotate.
DUAL RATE
■Select the next Menu Category by pressing the
‘MAIN_MENU’ button.
■The next Menu Category is ‘Dual Rate’.
■NOTE that only CH. 2 (Aileron), CH. 3 (Elevator)
& CH. 4 (Rudder) have Dual Rate facilities.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■Use the Dual Rate Switches on the transmitter
to toggle between the High and Low rate
settings.
■Use the ‘INC’ and ‘DEC’ buttons to make any
adjustments.

13
■Use the ‘SUB_MENU’ button to scroll through
to the next CH or function.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
SUB TRIM
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■The next Menu Category is the ‘Sub Trim’.
■The Sub Trim is used to fine tune the centre
point of the servo.
■Use the ‘SUB_MENU’ button to scroll through
to the next CH or function.
TRAVEL ADJUST
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■Press the ‘MAIN_MENU’ button to move to
the ‘TRV-ADJ’ (Travel Adjust) menu.
■This allows the total throw or movement of the
servo to be adjusted.
■Both ends of the servo travel can
be adjusted.
■To do so, move the appropriate
control stick in the direction that
requires adjustment.
■Use the ‘INC or ‘DEC’ button to
make any changes.
HELI AIR NOR IDLE NAME RST
CH1/L
CH2/1
CH3/2
CH4/3
CH5/H
CH6
INC
DEC
MAIN_MENU
SUB_MENU
POWER
ON
HELI AIR NOR IDLE NAME RST
CH1/L
CH2/1
CH3/2
CH4/3
CH5/H
CH6
INC
DEC
MAIN_MENU
SUB_MENU
POWER
ON
AIL-FLP
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■This menu is used to mix the aileron with the
flaps.
■Use the ’INC’ & ’DEC’ buttons to adjust the
values.

14
AIL-ELE
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■This menu is used to mix the aileron with the
elevator.
■Use the ’INC’ & ’DEC’ buttons to adjust the
values.
ELE-RUD
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■This menu is used to mix the elevator with the
rudder.
■Use the ’INC’ & ’DEC’ buttons to adjust the
values.
ELE-AIL
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■This menu is used to mix the elevator with the
aileron.
■Use the ’INC’ & ’DEC’ buttons to adjust the
values.
RUD-ELE
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
■This menu is used to mix the rudder with the
elevator.
■Use the ’INC’ & ’DEC’ buttons to adjust the
values.

15
THR-CUR (NORMAL)
■The next Menu or Category is the THR-CUR
(Throttle Curve) menu for ‘Normal’ or ‘Hover’
mode.
■NOTE the arrow pointing to ‘NOR’
■The throttle curve has 5 adjustable points.
■Use the ‘SUB_MENU’ button to scroll down to
each of the 5 points. CH1/L being the low point
and CH5/H being the high or 5th point on the
curve.
■Use the ‘INC’ & ‘DEC’ to change the values.
This shows the low point of the throttle curve in
Normal or Hover mode.
This shows the high point of the throttle curve in
Normal or Hover mode.
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
HELI AIR NOR IDLE NAME RST
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)
EXIT PROGRAMMING MODE
Press ‘MAIN_MENU’ & ‘SUB_MENU’ buttons
together to exit Programming Mode.
HELI AIR NOR IDLE NAME RST
INC
DEC
MAIN_MENU
SUB_MENU
CH1/LHold_ON/CCPM
CH2/1Mix (2-6)/NOR
CH3/2Mix(2-3)
CH4/3Mix(3-4)
CH5/HMix(3-2)
CH6Mix(4-3)

16
HELI---MODEL 1~4
1 2 3 4
MODEL1 3DST MODEL2 CP GOLD MODEL3 CPX MODEL4 CLEAR
1. REV----SW
①OFF ①OFF ①OFF ①OFF
②OFF ②ON ②OFF ②OFF
③ON ③OFF ③OFF ③OFF
④OFF ④OFF ④OFF ④OFF
⑤ON ⑤ON ⑤ON ⑤OFF
⑥OFF ⑥ON ⑥OFF ⑥OFF
2. D/R-AIL/ELE/RUD
Ail 0 position: 100% Ail 0 position: 100% Ail 0 position: 86% Ail 0 position: 100%
1 position :100% 1 position :100% 1 position :100% 1 position :100%
Ele 0 position: 100% Ele 0 position: 100% Ele 0 position: 84% Ele 0 position: 100%
1 position :100% 1 position :100% 1 position :100% 1 position :100%
Rud 0 position: 80% Rud 0 position: 100% Rud 0 position: 80% Rud 0 position: 80%
1 position :100% 1 position :100% 1 position :100% 1 position :100%
3. SB-TRIM
all =0 all =0 all =0 all =0
4. TRV-ADL
1.Thr -100% +100% 1.Thr -100% +100% 1.Thr -100% +100% 1.Thr -100% +100%
2.Ail +100% -100% 2.Ail +55% -100% 2.Ail +100% -100% 2.Ail +100% -100%
3.Ele +100% -100% 3.Ele +50% -100% 3.Ele +100% -100% 3.Ele +100% -100%
4.Rud -100% +100% 4.Rud -100% +100% 4.Rud -100% +100% 4.Rud -100% +100%
5.Ch5 -66% +66% 5.Ch5 -65% +80% 5.Ch5 -80% +45% 5.Ch5 -100% +100%
6.Ch6 +100% -100% 6.Ch6 +50% -100% 6.Ch6 +100% -100% 6.Ch6 +100% -100%
5. SW---TYP
Ail +60% Ail +60% Ail + 80% Ail +60%
Ele -35% Ele -60% Ele - 60% Ele -60%
Pit -60% Pit -60% Pit - 40% Pit -60%
6. THR-CUR
0%,25%,50%,75%,100% 0%,45%,70%,90%,100% 0%,30%,60%,80%,95% 0%,25%,50%,75%,100%
7. Idle
100%,84%,76%,87%,100% 100%,92%,85%,92%,100% 95%,75%,66%,75%,95% 100%,85%,75%,85%,100%
8. Normal Pitch
36%,60%,74%,88%,100% 30%,45%,60%,68%,79% 30%,50%,60%,75%,90% 0%,25%,50%,75%,100%
9. Idle Pitch
0%,25%,50%,75%,100% 0%,25%,50%,67%,79% 18%,38%,54%,71%,93% 0%,25%,50%,75%,100%
10. Hold Pitch
0%,25%,50%,75%,100% 0%,25%,50%,75%,100% 11%,25%,50%,71%,93% 0%,25%,50%,75%,100%
11. Hold Pitch
THR Hold: +006% THR Hold: +006% THR Hold: +006% THR Hold: +006%
transmittEr sEttings
HELICOPTER MODEL MEMORY MODELS 1-4
Model 1 is factory preset to operate the Twister 3D Storm
Model 2 is factory set operate the Twister CP Gold
Model 3 is factory set to operate the Twister CPX
Model 4 is named but is not factory preset for any specific helicopter therefore this is a free model
memory that will need programming for your specific application.

17
AIR--MODEL 1~4
1 2 3 4
ACRO ACRO ACRO ACRO
1. REV----SW
①OFF ①OFF ①OFF ①OFF
②OFF ②OFF ②OFF ②OFF
③ON ③OFF ③ON ③ON
④OFF ④OFF ④OFF ④OFF
⑤OFF ⑤OFF ⑤OFF ⑤OFF
⑥OFF ⑥OFF ⑥OFF ⑥OFF
2. D/R-AIL/ELE/RUD
Ail 0 position: 100% Ail 0 position: 100% Ail 0 position: 100% Ail 0 position: 100%
1 position :100% 1 position :100% 1 position :100% 1 position :100%
Ele 0 position: 100% Ele 0 position: 100% Ele 0 position: 100% Ele 0 position: 100%
1 position :100% 1 position :100% 1 position :100% 1 position :100%
Rud 0 position: 100% Rud 0 position: 100% Rud 0 position: 100% Rud 0 position: 100%
1 position :100% 1 position :100% 1 position :100% 1 position :100%
3. SB-TRIM
all =0 all =0 all =0 all =0
4. TRV-ADL
1 .Thr -100% +100% 1 .Thr -100% +100% 1 .Thr -100% +100% 1 .Thr -100% +100%
2.Ail +100% -100% 2.Ail +100% -100% 2.Ail +100% -100% 2.Ail +100% -100%
3.Ele +100% -100% 3.Ele +100% -100% 3.Ele +100% -100% 3.Ele +100% -100%
4.Rud -100% +100% 4.Rud -100% +100% 4.Rud -100% +100% 4.Rud -100% +100%
5.Ch5 -100% +100% 5.Ch5 -100% +100% 5.Ch5 -100% +100% 5.Ch5 -100% +100%
6.Ch6 -100% -100% 6.Ch6 -100% -100% 6.Ch6 -100% -100% 6.Ch6 -100% -100%
5. AIL FLP
0% 0% 0% 0%
6. AIL ELE
0% 0% 0% 0%
7. ELE RUD
0% 0% 0% 0%
8. ELE AIL
0% 0% 0% 0%
9. RUD ELE
0% 0% 0% 0%
10. THR CUR
0%,25%,50%,75%,100% 0%,25%,50%,75%,100% 0%,25%,50%,75%,100% 0%,25%,50%,75%,100%
AIRCRAFT MODEL MEMORY MODELS 1-4
There are no factory presets for any of these 4 aircraft models. If you wish to use this transmitter to
operate fixed wing models you must pay careful attention to model setup ensuring servo throws, mode
orientation (mode 1 or 2) are selected correctly and all other settings are correct for your specific
application.

18

19

Australasian agents: Model
Engines, Melbourne, Australia
www.modelengines.com.au
European agents: J Perkins
Distribution, Lenham, England
www.jperkinsdistribution.co.uk
2.4GHZ COMPUTER RADIO