TLW VEW K30-2052Z User manual

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
Kit Contents
▪RGB+CCT dimming Zigbee remote
Important Safety Information
DISCLAIMER: PLEASE NOTE INSTALLATION SHOULD BE CARRIED OUT BY A
QUALIFIED ELECTRICIAN!
•This Zigbee remote is a wireless transmitter that communicates with a variety of Zigbee compatible
systems. This transmitter sends wireless radio signals that are used to remotely control a compatible
system.
•This Zigbee remote supports 3 groups for binding max. 30 lighting devices and enables to control
DIM, CCT, RGB, RGBW and RGB+CCT Zigbee lighting devices.
•This device contains AAA batteries that shall be stored and disposed properly.
•DO NOT expose the device to moisture.
Function Introduction

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
Installation
Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
Removed from a Zigbee Network through Coordinator or Hub Interface
Factory Reset Manually
TouchLink to a Zigbee Lighting Device
1
From your ZigBee controller or hub interface, choose to delete or reset the remote as instructed,
indicator flashes 3 times quickly to indicate successful removing.

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
Remove a Touchlink Paired Zigbee Lighting Device
Factory Reset a Lighting Device (Touch Reset)

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
Find and Bind a Zigbee Lighting Device
Find and Unbind a Zigbee Lighting Device

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
Clear All Find and Bind Mode Paired Lighting Devices of a Group
Setup a Network & Add Devices to the Network (No Coordinator or Hub Required)

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
How to Check Whether the Remote Belongs to a Network or not
Battery Power Monitor Function
The remote will report battery power value to the coordinator under following situations:
•When powered on.
•When operating the switch to send data packets (over 4 hours since last operation).
•When added to the network by a coordinator.
Other Information
Specifications:
•Zigbee RGB+CCT+DIM remote based on Zigbee 3.0
•High sensitive & high stable touch colour wheel, fast & precise colour control
•Battery powered remote with low power consumption
•Enables to pair Zigbee lighting devices through touchlink commissioning
•Supports find and bind mode to pair with Zigbee lighting devices
•Supports 3 groups for binding max. 30 lighting devices
•With 6 preset scenes, enables to save and recall 5 scenes
•2.4 GHz global operation
•Transmission range up to 30m
•Compatible with universal Zigbee Gateway products
•Enables to bind and control universal DIM, CCT, RGB, RGBW and RGB+CCT Zigbee lighting devices
Zigbee Clusters Supported by This Remote Are As Follows:
Input clusters:
•Basic •Power Configuration •Identify •Diagnostics
Output clusters:
•Identify •Group •Scene •On/off •Level control •OTA •Colour control
OTA
The remote supports firmware updating through OTA, and will acquire new firmware from Zigbee controller
or hub every 10 minutes automatically.
1
Short press any other buttons except group buttons, indicator blinking means the wall switch has already
been added to a network, no blinking of indicator means the wall switch does not belong to any
network.

Product Name: Remote Ultra Ultra RGB+CCT LED Dimming Zigbee Remote
Product Code: K30-2052Z
Product Data