Twose TE480 User manual

TWOSE
TE480
Hedgecutter/Trimmer
Operator Manual
Publication 519 July 2006 (Revised 29.11.10)

IMPORTANT
VERIFICATION OF WARRANTY REGISTRATION
DEALER WARRANTY INFORMATION & REGISTRATION VERIFICATION
It is imperative that the selling dealer registers this machine with Twose of Tiverton Limited
before delivery to the end user – failure to do so may affect the validity of the machine
warranty.
To register machines go to the Twose web site at www.twose.com, log onto ‘Dealer
Inside’ and select the ‘Machine Registration button’which can be found in the Service
Section of the site. Confirm to the customer that the machine has been registered in the
section below.
Should you experience any problems registering a machine in this manner please contact
the Twose Office on 01884 253691.
Registration Verification
Dealer Name: ……………………..…………………………………………………………….
Dealer Address: …….………………………………………………………………………….
Customer Name: ……………………..…………………………………………………………
Date of Warranty Registration: ……/……/...…… Dealer Signature: ………………..……
NOTE TO CUSTOMER / OWNER
Please ensure that the above section above has been completed and signed by the selling
dealer to verify that your machine has been registered with Twose of Tiverton Limited.
IMPORTANT: During the initial ‘bedding in’ period of a new machine it is the customer’s responsibility
to regularly inspect all nuts, bolts and hose connections for tightness and re-tighten if required. New
hydraulic connections occasionally weep small amounts of oil as the seals and joints settle in – where
this occurs it can be cured by re-tightening the connection – refer to torque settings chart below. The
tasks stated above should be performed on an hourly basis during the first day of work and at least
daily thereafter as part of the machines general maintenance procedure.
TORQUE SETTINGS FOR HYDRAULIC FITTINGS
HYDRAULIC HOSE ENDS PORT ADAPTORS WITH BONDED SEALS
BSP Setting Metric
BSP Setting Metric
1/4” 18 Nm 19 mm 1/4” 34 Nm 19 mm
3/8” 31 Nm 22 mm 3/8” 47 Nm 22 mm
1/2” 49 Nm 27 mm 1/2” 102 Nm 27 mm
5/8” 60 Nm 30 mm 5/8” 122 Nm 30 mm
3/4” 80 Nm 32 mm 3/4” 149 Nm 32 mm
1” 125 Nm 41 mm 1” 203 Nm 41 mm
1.1/4” 190 Nm 50 mm 1.1/4” 305 Nm 50 mm
1.1/2” 250 Nm 55 mm 1.1/2” 305 Nm 55 mm
2” 420 Nm 70 mm 2” 400 Nm 70 mm

WARRANTY POLICY
WARRANTY REGISTRATION
All machines must be registered, by the selling dealer with Twose of Tiverton Limited before delivery to the
end user. On receipt of the goods it is the buyer’s responsibility to check that the Verification of Warranty
Registration in the Operator’s Manual has been completed by the selling dealer.
1. LIMITED WARRANTIES
1.01. All machines supplied by Twose of Tiverton Limited are warranted to be free from defects in material
and workmanship from the date of sale to the original purchaser for a period of 12 months, unless a
different period is specified.
1.02. All spare parts supplied by Twose of Tiverton Limited are warranted to be free from defects in material
and workmanship from the date of sale to the original purchaser for a period of 6 months.
1.03. The manufacturer will replace or repair for the purchaser any part or parts found, upon examination at
its factory, to be defective under normal use and service due to defects in material or workmanship.
Returned parts must be complete and unexamined.
1.04. This warranty does not apply to any part of the goods, which has been subjected to improper or
abnormal use, negligence, alteration, modification, fitment of non-genuine parts, accident damage, or
damage resulting from contact with overhead power lines, damage caused by foreign objects (e.g.
stones, iron, material other than vegetation), failure due to lack of maintenance, use of incorrect oil or
lubricants, contamination of the oil, or which has served its normal life. This warranty does not apply to
any expendable items such as blades, flails, flap kits, skids, soil engaging parts, shields, guards, wear
pads or pneumatic tyres.
1.05. Temporary repairs and consequential loss - i.e. oil, downtime and associated parts are specifically
excluded from the warranty.
1.06. Warranty on hoses is limited to 12 months and does not include hoses which have suffered external
damage. Only complete hoses may be returned under warranty, any which have been cut or repaired
will be rejected.
1.07. Machines must be repaired immediately a problem arises. Continued use of the machine after a
problem has occurred can result in further component failures, for which Twose of Tiverton Limited
cannot be held liable, and may have safety implications.
1.08. Except as provided herein, no employee, agent, dealer or other person is authorised to give any
warranties of any nature on behalf of Twose of Tiverton Limited.
1.09. For machine warranty periods in excess of 12 months the following additional exclusions shall apply:
1) Hoses, external seals, exposed pipes and hydraulic tank breathers.
2) Filters.
3) Rubber mountings.
4) External electric wiring.
N.B. Warranty cover will be invalid if any non-genuine parts have been fitted or used. Use of non-
genuine parts may seriously affect the machine’s performance and safety. Twose of Tiverton Limited
cannot be held responsible for any failures or safety implications that arise due to the use of non-
genuine parts.

2. REMEDIES AND PROCEDURES
2.01. The warranty is not effective unless the Selling Dealer registers the machine, via the Twose web site
and confirms the registration to the purchaser by completing the Verification of Warranty Registration
in the operator’s manual.
2.02. Any fault must be reported to an authorised Twose dealer as soon as it occurs. Continued use of a
machine, after a fault has occurred, can result in further component failure for which Twose of Tiverton
Limited cannot be held liable.
2.03. Repairs should be undertaken within two days of the failure. Claims submitted for repairs undertaken
more than 2 weeks after a failure has occurred, or 2 days after the parts were supplied will be rejected,
unless the delay has been authorised by Twose of Tiverton Limited.
2.04. All claims must be submitted, by an authorised Twose Service Dealer, within 30 days of the date of
repair.
2.05. Following examination of the claim and parts the manufacture will pay, at their discretion, for any valid
claim the cost of any parts and an appropriate labour allowance if applicable.
2.06. The submission of a claim is not a guarantee of payment.
2.07. Any decision reached by Twose of Tiverton Limited is final.
3. LIMITATION OF LIABILITY
3.01. The manufacturer disclaims any express (except as set forth herein) and implied warranties with
respect to the goods including, but not limited to, merchantability and fitness for a particular purpose.
3.02. The manufacturer makes no warranty as to the design, capability, capacity or suitability for use of the
goods.
3.03. Except as provided herein, the manufacturer shall have no liability or responsibility to the purchaser or
any other person or entity with respect to any liability, loss, or damage caused or alleged to be caused
directly or indirectly by the goods including, but not limited to, any indirect, special, consequential, or
incidental damages resulting from the use or operation of the goods or any breach of this warranty.
Notwithstanding the above limitations and warranties, the manufacturer’s liability hereunder for
damages incurred by the purchaser or others shall not exceed the price of the goods.
3.04. No action arising out of any claimed breach of this warranty or transactions under this warranty may be
brought more than one (1) year after the cause of the action has occurred.
4. MISCELLANEOUS
4.01. The manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver
of any terms shall be deemed to be a waiver of any other term.
4.02. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable,
then the invalidity of such provision shall not invalidate any other provisions herein.
4.03. Applicable law may provide rights and benefits to the purchaser in addition to those provided herein.

THIS MANUAL IS TO BE HANDED TO THE CUSTOMER BEFORE
THE MACHINE IS TO BE USED FOR THE FIRST TIME.
THIS MANUAL (OR A COPY OF) MUST BE USED AND READ BY
ALL OPERATORS OF THIS MACHINE.
TWOSE OF TIVERTON LIMITED
6 CHINON COURT
LOWER MOOR WAY
TIVERTON BUSINESS PARK
TIVERTON
DEVON
EX16 6SS
Telephone: [phone]
Fax: [phone]
All dimensions and capacities mentioned in this book are approximate. In pursuance of the company’s
policy of constant development, the right is reserved to depart, without notice, from any detail illustrated
or specified in this book, without incurring the obligation to provide such modifications on the machine
previously delivered.
No responsibility will be accepted by Twose of Tiverton Limited for any injury, damage or loss arising
from the improper use of or lack of maintenance of any machinery supplied by them or from any failure
of the user to comply with all instructions published by Tractor or Loader Manufacturers, particularly
with the regard to maximum load capacities, tyre pressures and stability, or with instructions and
regulations pertaining to Tractor Cabs.

DECLARATION OF CONFORMITY
Conforming to EU Machinery Directive 2006/42/EC
We,
TWOSE of TIVERTON LIMITED,
6 Chinon Court, Lower Moor Way,
Tiverton Business Park, Tiverton, Devon, EX16 6SS, UK
Hereby declare that:
The Product; Tractor Mounted Hedgecutter / Grass Mower
Product Code; T480
Serial No. & Date ………………………………… Type …………………………
Manufactured in; United Kingdom
Complies with the required provisions of the Machinery Directive 2006/42/EC
The machinery directive is supported by the following harmonized standards;
BS EN ISO 14121-1 (2007) Safety of machinery - Risk assessment, Part 1:
Principles Part 2: practical guide and examples of methods.
BS EN ISO 12100-1 (2010) Safety of machinery - Part 1: Basic terminology and
methodology Part 2: Technical principles.
BS EN 349(1993)+ A1 (2008) Safety of machinery - Minimum distances to avoid the
entrapment with human body parts.
BS EN 953 (1998) Safety of machinery - Guards General requirements for the
design and construction of fixed and movable guards.
BS EN 982(1996)+ A1 (2008) Safety requirements for fluid power systems and their
components. Hydraulics
Signed ……………….... Responsible Person
on behalf of TWOSE of TIVERTON LIMITED
Status: General Manager Date: May 2011

DECLARATION OF CONFORMITY
Conforming to EU Machinery Directive 2006/42/EC
We,
TWOSE of TIVERTON LIMITED,
6 Chinon Court, Lower Moor Way,
Tiverton Business Park, Tiverton, Devon, EX16 6SS, UK
Hereby declare that:
The Product; Hydraulic Arm Mounted Flailhead
Product Code; TWHD
Serial No. & Date ………………………………… Type …………………………
Manufactured in; United Kingdom
Complies with the required provisions of the Machinery Directive 2006/42/EC
The machinery directive is supported by the following harmonized standards;
BS EN ISO 14121-1 (2007) Safety of machinery - Risk assessment, Part 1:
Principles Part 2: practical guide and examples of methods.
BS EN ISO 12100-1 (2010) Safety of machinery - Part 1: Basic terminology and
methodology Part 2: Technical principles.
BS EN 349(1993)+ A1 (2008) Safety of machinery - Minimum distances to avoid the
entrapment with human body parts.
BS EN 953 (1998) Safety of machinery - Guards General requirements for the
design and construction of fixed and movable guards.
BS EN 982(1996)+ A1 (2008) Safety requirements for fluid power systems and their
components. Hydraulics
Signed ……………….... Responsible Person
on behalf of TWOSE of TIVERTON LIMITED
Status: General Manager Date: May 2011