Tyco Illustra Flex Gen 3 User manual

Quick Start Guide
(8200-1937-09_C0)
Illustra Flex Gen 3 Outdoor Dome Camera
In the box
y1 x Dome camera
y1 x Mounting template sticker
y1 x Mounting plate
y3 x 10x4mm mounting plate screws
y3 x 40x6mm plastic screws anchors
y3 x 50x4mm tapping screws
y1 x Cap Installer
y3 x Cable Bush
y1 x Printed Quick Start Guide
y1 x Torx driver
y1 x Safety wire
y2x 8x3mm screw
Installation tools
y1 x Screw Driver
y1 x Torx driver
y1 x Drill
Table 1: Camera part descriptions
Camera Part Description
1
Mounting Plate
2
Cable side entry
3
Camera base
4
Camera lens
5
Dome Cover
Mounting and powering up the camera
1. Place the mounting template sticker on the surface that you want to
attach the camera.
2. On the surface drill three Ø6mm holes, cut out a larger Ø 60mm
cabling hole and triangle as per the markings identied on the mounting
template sticker.
3. Securely place the three screw anchors into the three Ø 6mm holes.
4. Unscrew the three screws on the camera dome (5) (Figure 1) to remove
the dome from the camera base (3) (Figure 1).
5. Insert the PoE cable or AC24V cable through the hole on thecamera
base.
Note: Ensure that the rubber plugs on the cable is correctly inserted
into the cable hole on the camera base.
Mounting and powering up the camera (continued)
6. Connect the PoE cable to the PoE slot on the camera.
OR
Connect the AC24V cable to the AC24 connection on the camera.
7. Before you lock the mounting plate (1) (Figure 2) to the camera base
you must place the cable through the cable side entry slot on the
camera base (2) (Figure 1) or through the cable hole in the camera
mounting plate.
y When using the cable side entry slot you must rst remove the cable
side entry screw that holds the cable side entry cover in place.
yIf the cable is placed through the hole on the camera mounting plate
then insert the cable through the hole on the mounting surface.
8. Place the camera base onto the mounting plate and rotate the camera
base to lock it to the mounting plate.
Note: The mounting plate includes a ‘lock’ and ‘unlock’ symbol to assist
with step 8.
9. Hold the mounting plate with camera base up to the mounting template
and align the three holes on the mounting template with the three holes
on the camera base.
10. Insert the three screws into the three holes on the camera base and
securely attach the mounting plate and camera base to the surface.
11. Cover the camera with the dome cover and securely attach the dome
to the camera with the three screws.
Mounting and powering up the camera (continued)
12. Connect the AC24V cable to the AC 24V terminal or connect the
RJ-45 jack to a PoE compatible network device that supplies power
through the Ethernet cable.
Camera buttons and connections: Figure 2
Table 2: Camera buttons and connections descriptions
Camera button /
connection Description
1
AC cable connection
2
Factory reset
yHold for 5 seconds for soft reset
yHold for 20 seconds for hard reset
3
Focus button
yHold for 3 seconds to runone touch focus
4
USB cable connection
5
Micro SD card slot
6
Audio / Alarm cable connection
7
PoE cable slot
Quick reference
yDefault IP: 192.168.1.168 (DHCP enabled)
yDefault Username / Password: admin / admin
yPower: AC24V / PoE 802.3af
Camera Parts: Figure 1
Figure 1
1
3
5
4
2
Figure 2
1
2
3
4
5 6
7

Warnings
yThis product is intended for professional installation, please follow local
wiring regulations.
yTo meet EU security immunity requirements this product should be used
with an Uninterruptable Power Supply to feed the mains input of any power
adaptor.
yThe product should be powered by a limited power supply (LPS) sized
according to the product rating label.
yThe LAN symbol on the unit means this is not intended for connection to a
public network or a LAN from a di󰀨erent building.
yDo not install where children are likely to have access.
yFor outdoor use the camera should be mounted at least 3m above ground
level.
© 2020 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or
registered trademarks. Unauthorized use is strictly prohibited.
Adjusting the camera position: Figure 3
Figure 3
1
2
3
1. Rotate: The rotate range of the 3-axis gimbal is 0° to a minimum of
355°.
2. Tilt: The tilt range of the 3-axis gimbal is 0° to 67°.
3. Pan: The pan range of the 3 axis gimbal is 0° to 355°.
Table 3: Mounting plate symbols and descriptions
Symbol Name Description
A Single Gang Box
Attach the plate to a North American
single gang electrical box.
B Octagon Box
Attach the plate to a North American
octagon electrical box.
C Double Gang Box
Attach the plate to a North American
double gang electrical box.
D 4S Junction Box
Attach the plate to a North American
4 inch square electrical box.
PT01-005695A