Tyco Illustra Standard Series User manual

Package
Overview
Installation
1
2
3
4
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Keep away from liquid while in use.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall, the device shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold, dusty or damp
locations, and do not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
① Insert a micro SD card into the card slot as shown below.
Auto Iris InterfaceAuto Iris Interface
Microphone
Focus Adjusting
Camera Quick start guide CD
Terminal block for power
5
10
6
11
12
1
2
7
3
8
4
9
Power port ( 12V/ 24V)DC AC
Video output
Alarm output
Restore factory default setting
Audio input
Audio output
Power indicator
Alarm input
Ground
Ethernet connector (PoE)
Micro SD card slot
■ Please read this instruction carefully before using the product and
keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without notice.
1
6
2
7 8
3
9
4
10
5
11 12
RS48 5 AL ARM I N
A B 1 GND1 2 GND2 1A 1 B 2A 2B
ALAR M OU T
TF CARD
RS 485; connectors for PTZ
Screwdriver
Cable
RS 485/ Alarm input/Output Cable Connection
Use the small slotted screwdriver to press the
corresponding button. Then insert the cable into
the cable groove. After that, release the screwdriver.
Sensor
IPC
GND1/GND2
Alarm Input:
Alarm
Power
IPC
1A/2A
1B/2B
+
+
-
-
Alarm Output:
* Default: Restore device factory default setting. When system is running
normally, press and hold the DEFAULT button for 10 seconds, the system
can restore factory default setting.
*Power indicator: red light means the camera is powered normally.
② Remove the protection cover of the lens interface and then install
the lens (not supplied) to the camera. Rotate the lens clockwise
until it is fixed firmly. Then plug the cable of auto iris to the auto
iris interface of the camera.
Insert a micro SD card
1 2
/
Please make sure that the wall is strong enough to withstand 3 times
the weight of the camera and the bracket. Please install the camera
under dry environment. Here we take wall mounting for example.
VIDEO OUT
Focus Adjusting: When it still fails to realize focusing after having
confirmed the correct installation of lens, the back focus adjustment
may be required.
Illustra Standard Series
Box Camera
Quick Start Guide
V
ISV-X02N003S
ISV-X02N004S

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
③ Fix the bracket to the wall with screws.
④ Secure the camera onto the bracket with screws as shown below.
Then connect the relevant cables.
⑤ Loosen the adjusting screws to set the monitoring direction of
the camera as shown below. After that, tighten the adjusting screw
firmly.
⑥ Zoom and focus adjustment--adjust the zoom level and focus
level manually (if applicable) or adjust the back focus.
Note: CS-mount lens can be directly installed to the lens interface. C-mount
lens needs to install a C/CS adapter ring.
There is no need to plug the power cable of the auto-iris to the auto-iris
interface if a manual-iris lens is used.
Adjusting Screw
● Access the camera through TycoIPTool
① Make sure that the camera and the PC are well connected to the
LAN.
② Find the TycoIPTool from the CD and then install it in the
computer. After that, run the TycoIPTool as shown below.
③ Modify the IP address. The default IP address of this camera is
192.168.1.168. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
About
Immediate Refresh
Device Na me
name
name
name
IPC
IPC
IPC
xxx
xxx
xxx
192.168.1.168
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Device Type
Product M odel
IP Address Http Port Data Port Subnet Mo dify Net work Parameter
Mac Addres s
IP Address
Subnet Ma sk
Gateway
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 168
255 . 255 . 255 . 0
192 . 168 . 1 . 1
Tip: E nter the administrator passwo rd, and
then modi fy the net work parameters.
Restore I PC Defau lt Configuration
Total Devic e: 3
Local IP Address:192.16 8.1.4Subne t Mask:255.255.255.0 Gateway : 192.168.1.1DNS：210.21.196.6
i
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X and the
gateway shall be changed to 192.168.1.1. After modification, please
enter the password of the administrator and click “Modify” button to
modify the settings.
The default password of the administrator is “ ”.admin
④ Double-click the camera listed in the IP-Tool or manually enter the
IP address in the address bar of the web browser to connect IP-CAM.
Then follow directions to download and install the plugin.
⑤ Enter the username and password in the login interface.
The default username is admin; the default password is admin.
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 168
255 . 255 . 255 . 0
192 . 168 . 1 . 1
Tip: Enter the administrator password, and
then modify the network parameters.
i
Modify Network Parameter