Tyco Illustra Flex Gen 3 User manual

Quick Start Guide
(8200-1937-03_B0)
Illustra Flex Gen 3 Compact Dome Camera
In the box
y1 x Compact Dome camera
y1 x Mounting template sticker
y1 x Mounting plate
y3 x 40x6mm plastic screw anchors
y3 x 50x4mm tapping screws
y3 x 10x4mm mounting plate screws
y1 x Printed Quick Start Guide
y1 x Waterproof RJ45 cable accessory
y1 x Torx driver
Installation tools
y1 x Screw driver
y1 x Torx driver
y1 x Drill
Table 1: Camera part descriptions
Camera Part Description
1
Mounting Plate
2
Camera Base
3
Camera body
4
Camera lens
5
Dome cover
Mounting and powering up the camera
1. Place the mounting template sticker on the mounting surface.
2. On the mounting surface drill three Ø 6mm holes and cut out an
Ø 22mm cabling hole as per the markings identied on the mounting
template sticker.
3. Securely place the three screw anchors into the three Ø 6mm holes.
4. Unscrew the three screws on the camera dome (5) (Figure 1) to remove
the dome cover from the camera base.
5. Place the PoE cable:
a. through the cable side entry slot on the camera base (2) (Figure 1).
OR
b. through the cable hole on the mounting plate (1) (Figure 1).
Mounting and powering up the camera (continued)
6. Place the camera base (2) (Figure 1) on to the camera mounting plate
(1) (Figure 1) and ensure that the three holes on the camera base align
with the three holes on the mounting plate.
Note: If the PoE cable is placed through the cable hole on the mounting
plate then insert the PoE cable through the Ø 22mm hole on the
mounting surface.
7. Hold the mounting plate and camera base up to the mounting template
and align the three holes on the mounting plate and camera base with
the three holes on the mounting template.
8. Insert the three screws onto the three holes on the camera base and
securely attach the mounting plate and camera base to the surface.
9. Cover the camera body with the dome cover (5) (Figure 1) and securely
attach the dome to the camera with the three screws.
10. Connect the RJ-45 jack to a PoE compatible network device that
supplies power through the Ethernet cable.
Camera buttons and connections: Figure 2
Figure 2
31
2
Table 2: Camera buttons and connections descriptions
Camera button /
connection Description
1
Reset button
yHold for 5 seconds for soft reset
yHold for 20 seconds for hard reset
2
Micro SD card
3
USB cable connection
Adjusting the camera position: Figure 3
Figure 3
3
2
1
1. Rotate: The rotate range of the 3-axis gimbal is 0° to a minimum of
355°
2. Tilt: The tilt range of the 3-axis gimbal is 0° to 67°.
3. Pan: The pan range of the 3 axis gimbal is 0° to 355°.
Figure 1
1
2
3
4
5
Quick reference
yDefault IP: 192.168.1.168 (DHCP enabled)
yDefault Username: admin
yDefault Password: admin
yPower: PoE 802.3af
Camera Parts: Figure 1

Warnings
yThis product is intended for professional installation, please follow local
wiring regulations.
yTo meet EU security immunity requirements this product should be used
with an Uninterruptable Power Supply to feed the mains input of any power
adaptor.
yThe product should be powered by a limited power supply (LPS) sized
according to the product rating label.
yThe LAN symbol on the unit means this is not intended for connection to a
public network or a LAN from a di󰀨erent building.
yDo not install where children are likely to have access.
yFor outdoor use the camera should be mounted at least 3m above ground
level.
© 2020 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or
registered trademarks. Unauthorized use is strictly prohibited.
Table 3: Mounting plate symbols and descriptions
Symbol Name Description
A Single Gang Box
Attach the plate to a North American
single gang electrical box.
B Octagon Box
Attach the plate to a North American
octagon electrical box.
C Double Gang Box
Attach the plate to a North American
double gang electrical box.
D 4S Junction Box
Attach the plate to a North American
4 inch square electrical box.
PT01-005694A