UBERHAUS DESIGN 06105006 User manual

Model / Modèle: 06105006
FREESTANDING BATHTUB
BAIGNOIRE AUTOPORTANTE

Use only components (drainer, overflow pipes, valves and fittings) that
do not require any welding during the assembly.
Carefully read the installation manual before beginning the installation.
Consult local building codes to make sure the installation complies with
your local standards.
To protect the unit during installation, we recommend that you lay a piece
of cardboard on the bottom.
Please check the product carefully for any visible damages prior to installation.
Contact Customer service if any damage is found.
This bathtub is made of acrylic and fibreglass.
We recommend that the installation be done by 2 persons.
Preheat the bathtub with warm water (18-20°C) before using, if the room
temperature is too low. Please do not let hot water (more than 50°C) hit the
bathtub directly. Drain the water completely after using, then wipe the bathtub
with a soft cloth. Make sure there is no water left in the bathtub.
Regular disinfection provides an effective defense against various types of
bacteria susceptible of developing in the deposits that build up over time in
all bathtubs and showers.
For daily maintenance cleaning, use a moist cloth and gentle liquid detergent.
For acrylic surfaces, occasional use a special acrylic surface cleaner will add
luster and protect the finish.
Do not use abrasive cleaners, scrapers, metal brushes, or any items or products
that could scratch or dull the surface.
Paint stains: use either turpentine or a paint thinner..
Joint compound stains: use a plastic or wood spatula covered with a damp
cloth. Do not use a metal blade or a metal brush.
If a rubber mat is used, it must be removed immediately after each use. Ignoring
this recommendation will cause damage not covered by the warranty.
Before you begin
Maintenance
1

Part#
Reference dimensions
2
Parts list
Description Qty
Drainer 1
Required tools
Pecil
Sillicone Sealant
Level
Tape Measure
Adjustable Spanner wrench

3
Adjust the feet screws
Decide exactly where you wish to install your bathtub and gently put it down
where decided.
Important:The unit must be installed on a leveled floor.The floor must support
50 lbf/ft² (245 kgf/m²)
Outline the base of the bathtub on the floor with a pencil. Adjust the feet
screws to make sure the bathtub can be level on the floor.
1. Leveling

4
It is recommended to have a competent, professional plumber do the
plumbing
connections.
Gently move the bathtub and install the basic plumbing parts to connect
the bathtub drain to the floor drain components: water inlet and floor drain.
2. Plumbing
3. Mandatory Test
The bathtub must be tested before installation is complete. Pour some
water into the bathtub to test drainage and check for leaks. If necessary,
tightening with a spanner wrench. If a leak is found,
is properly level.
Hot water Cold water
adjust inner legs by
adjust bathtub to make sure it
Apply a silicone pressure joint on the floor.. And put back the bathtub at the
specified area, then wipe off the silicone excess.

5
Thank you for purchasing a UBERHAUS Design product. These
products have been made to demanding, high-quality standards
and are guaranteed for domestic use against manufacturing faults
for a period of 2 years from the date of purchase.
This warranty does not af fect your statutory rights. In case of any
malfunction of you UBERHAUS Design product (failure, missing part,
etc.), please contact one of our service technicians at our toll free
to 6 PM, Monday to Friday,
Eastern time. RONA reserves the right to repair or replace the defective
product, at its discretion.
The product is guaranteed for 2 years if used for normal trade purposes.
Any warranty is invalid if the product has been overloaded or subject to
neglect, improper use or an attempted repair other than by an authorized
agent. Heavy-duty or daily professional/commercial usage are not guaranteed.
Due to continuous product improvement, we reserve the right to change the
product specifications without prior notice.
WARRANTY
service line at 1-866-206-0888 from 8 AM